TEGERA 43001 Protective Gloves Instructions

TEGERA 43001 Protective Gloves

Product Information

• Standard: EN ISO 21420:2020
• Protection Standards: EN 388:2016+A1:2018
• Outer Material Specification: Polyurethane
• Inner Material Specification: HPPE (High-performance polyethylene), elastane, nylon, polyester
• Size Range (EU): 5, 6, 7, 8, 9, 10, 11
• EU-Type Examination: 0075 CTC, 4 rue Hermann Frenkel, 69367 Lyon Cedex 07 France
• UKCA-Type Examination: 0321 SATRA Technology Centre, Wyndham Way, Telford Way, Kettering, Northamptonshire, NN16 8SD, United Kingdom
• Quantity: 12 pairs
• Country of Origin: Made in China
• Imported by: Ejendals Ltd, Sweden House, 5 Upper Montagu Street, London, England, W1 2AG
• Contact Information: [email protected] | [email protected] | www.ejendals.com
• Declaration of Conformity: www.ejendals.com/conformity

Product Usage Instructions

1. Carefully read these instructions before using this product.
2. Warning! This product is designed to provide protection specified in PPE Regulation (EU) 2016/425 and PPE Regulation 2016/425 as amended and brought into UK law with the detailed levels of performance presented below. However, always remember that no item of PPE can provide full protection and caution must always be taken when exposed to risks.
3. Avoid using these gloves near moving elements or machinery with unprotected parts.
4. Ensure the glove size is suitable for your hand. Products that are either too loose or too tight will restrict movement and will not provide optimal protection.
5. Replace gloves regularly for hygienic use.
6. The shelf life of this product cannot be determined as it will be affected by factors such as storage conditions and usage.
7. Care and maintenance: Gloves/sleeves that can be mechanically washed will carry laundry symbols. The customer or launderer is responsible for the performance of the gloves after laundering when the gloves have already been used.

Cut-resistant glove, PU, palm-dipped, smooth finish, cut resistance level B, 13 gg, CRF® Technology, nylon, polyester, spandex, Cat. II, grey, white, for fine assembly work

INSTRUCTIONS FOR USE

Carefully read these instructions before using this product.
EXPLANATION OF PICTOGRAMS 0 = Below the minimum performance level for the given individual hazard X= Not submitted to the test or test method not suitable for the glove design or material
Warning! This product is designed to provide protection specified in PPE Regulation (EU) 2016/425 and PPE Regulation 2016/425 as amended and brought into UK law with the detailed levels of performance presented below. However, always remember that no item of PPE can provide full protection and caution must always be taken when exposed to risks.

• A. Abrasion resistance Min. 0; Max. 4

• B. Blade cut resistance Min. 0; Max. 5

• C. Tear resistance Min. 0; Max. 4

• D. Puncture resistance Min. 0; Max. 4

• E. Cut Resistance TDM Min. A; Max. F (EN ISO13997),

• F. Impact Protection P=Pass

• Abrasion resistance according to the American National Standard Institute 105-2016. Levels 1-6

• Cut resistance according to the American National Standard Institute 105-2016. Levels A1-A9

PROTECTIVE GLOVES AGAINST MECHANICAL RISKS

Protection levels are measured from the area of the glove palm.
Warning : For gloves with two or more layers the overall classification of EN 388:2016 +A1:2018 does not necessarily reflect the performance of the outmost layer. Do not use these gloves near moving elements or machinery with unprotected parts. For dulling during the cut resistance test, the coupe test results are only indicative while the TDM cut resistance test is the reference performance result.
EN ISO 21420:2020 PROTECTIVE GLOVES

GENERAL REQUIREMENTS AND TEST METHODS

• Finger dexterity test: Min. 1; Max. 5
  FITTING AND SIZING : All sizes comply with EN ISO 21420:2020 for comfort, fit, and dexterity, if not explained on the front page. If the short model symbol is shown on the front page, the glove is shorter than a standard glove, in order to enhance comfort for special purposes – for example, fine assembly work. Only wear the products in a suitable size. Products that are either too loose or too tight will restrict movement and will not provide the optimal level of protection.

• STORAGE AND TRANSPORT: Ideally stored in dry and dark condition in the original package, between +10º – +30ºC.

• INSPECTION BEFORE USE: Check that the glove does not present holes, cracks, tears, color changes etc. If the product becomes damaged it will NOT provide the optimal protection and must be disposed of. Never use a damaged product. Wear (or take off) gloves one at a time. Replace gloves regularly for hygienic use

• SHELF LIFE : The nature of the materials used in this product means that the life of this product cannot be determined as it will be affected by many factors, such as storage conditions, usage etc.

CARE AND MAINTENANCE

Gloves/sleeves that can be mechanically washed will carry laundry symbols. It is the customer or launderer who is responsible for the performance of the gloves after laundering when the gloves have already been used. Ejendals cannot be held liable for this

DISPOSAL

• According to local environmental legislation.
• The glove contains natural rubber which may cause allergy.

ALLERGENS:
This product may contain components that may be a potential risk to allergic reactions. Do not use in case of hypersensitivity signs. For more information contact Ejendals.

latex free

****DECLARATION OF CONFORMITY

www.ejendals.com/conformity

• OUTER MATERIAL SPECIFICATION Polyurethane
• INNER MATERIAL SPECIFICATION HPPE (High performance polyethylene), elastane, nylon, polyester
• SIZE RANGE (EU) 5,6,7,8,9,10,11
• EU-TYPE EXAMINATION 0075 CTC, 4 rue Hermann Frenkel, 69367 Lyon Cedex 07 France

UKCA-TYPE EXAMINATION 0321 SATRA Technology Centre, Wyndham Way, Telford Way, Kettering, Northamptonshire, NN16 8SD, United Kingdom

References

• Conformity

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>