TEGERA 879 ESD Gloves Instruction Manual
- June 4, 2024
- TEGERA
Table of Contents
879 ESD Gloves Instruction Manual
INSTRUCTIONS FOR USE PRODUCT SPECIFIC INFORMATION ONLY ON THIS PAGE
Synthetic glove, nitrile foam, palm-dipped, foam grip pattern, 18 gg, carbon,
nylon, spandex, Cat. II, black, blue, grey, latex-free, silicone-free, for
touchscreen, for precision work
EN ISO 21420:2020
EN 388:2016+A1:2018
4110X
EN 407:2020 No Flame Protection
X1XXXX
IEC 61340-5-1:2016
R < 1.0 x 10⁹ Ω
EN 16350:2014
R < 1,0 x 10⁸ Ω
Contact heat valid for coated area only, Do not wash
OUTER MATERIAL SPECIFICATION Nitrile
INNER MATERIAL SPECIFICATION Nylon, carbon thread, elastane
SIZE RANGE (EU) 6,7,8,9,10,11,12
EU-TYPE EXAMINATION 2777 Satra Technology Europe Ltd Bracetown Business
Park, Clonee, Dublin 15, Dublin, Ireland
UKCA-TYPE EXAMINATION
0321 SATRA Technology Centre, Wyndham Way, Telford Way, Kettering,
Northamptonshire, NN16 8SD, United Kingdom
INSTRUCTIONS FOR USE – CATEGORY II SEE THE FRONT PAGE FOR PRODUCT-SPECIFIC
INFORMATION
Carefully read these instructions before using this product. DECLARATION OF
CONFORMITY www.ejendals.com/conformity
EXPLANATION OF PICTOGRAMS 0 = Below the minimum performance level for the
given individual hazard X= Not submitted to the test or test method not
suitable for the glove design or material
Warning! This product is designed to provide protection specified in PPE
Regulation (EU) 2016/425 and PPE Regulation 2016/425 as amended and brought
into UK law with the detailed levels of performance presented below. However,
always remember that no item of PPE can provide full protection and caution
must always be taken when exposed to risks.
PROTECTIVE GLOVES AGAINST THERMAL RISKS (HEAT AND/OR FIRE) EN 407:2020
ABCDEF| A: Limited flame spread
B: Contact heat
C: Convective heat
D: Radiant heat
E: Small splashes of molten metal
F: Large quantities of molten metal| PERFORMANCE (A-F)
Min. 0; Max. 4
---|---|---
EN 388:2016
+A1:2018
| A. Abrasion resistance
B. Blade cut resistance
C. Tear resistance
D. Puncture resistance
E. Cut Resistance TDM (EN ISO13997),
F. Impact Protection| Min. 0; Max. 4
Min. 0; Max. 5
Min. 0; Max. 4
Min. 0; Max. 4
Min. A; Max. F
P=Pass
---|---|---
IEC 61340-5-1
DERMATEST
Dermatologically tested. This product did not lead to toxic- irritative
intolerance reactions in patch testing on humans carried out in accordance
with international guidelines.
EN 16350:2014
PROTECTIVE GLOVES – ELECTROSTATIC
PROPERTIES Warning: EN 16350:2014: The person wearing the electrostatic
dissipative protective gloves shall be properly earthed, e.g., by wearing
adequate footwear. electrostatic dissipative protective gloves shall not be
unpacked, opened, adjusted, or removed whilst in flammable or explosive
atmospheres or while handling flammable or explosive substances. The
electrostatic properties of the protective gloves might be adversely affected
by aging, wear, contamination, and damage, and might not be sufficient for
oxygen-enriched flammable atmospheres where additional assessments are
necessary. Test carried out at 25% relative humidity and at test potential,
100 V. Glove specimens taken from the palm.
EN ISO 21420:2020 PROTECTIVE GLOVES – GENERAL REQUIREMENTS AND TEST METHODS
Finger dexterity test: Min. 1; Max. 5
FITTING AND SIZING: All sizes comply with the EN ISO 21420:2020 for
comfort, fit, and dexterity, if not explained on the front page.
If the short model symbol is shown on the front page, the glove is shorter
than a standard glove, in order to enhance the comfort for special purposes –
for example, fine assembly work. Only wear the products in a suitable size.
Products that are either too loose or too tight will restrict movement and
will not provide the optimal level of protection.
STORAGE AND TRANSPORT: Ideally stored in dry and dark condition in the
original package, between +10º – +30ºC.
INSPECTION BEFORE USE: Check that the glove does not present holes,
cracks, tears, color changes etc. If the product becomes damaged it will NOT
provide the optimal protection and must be disposed of. Never use a damaged
product. Wear (or take off) gloves one at a time. Replace gloves regularly for
hygienic use
SHELF LIFE: The nature of the materials used in this product means that
the life of this product cannot be determined as it will be affected by many
factors, such as storage conditions, usage etc.
CARE AND MAINTENANCE: The user bares sole responsibility for submitting
the product to mechanical washing after use, as unknown substances can
contaminate the product during use and may affect the performance levels of
the product. To care for your product, we recommend that you rinse in cold
water and line dry in room temperature.
DISPOSAL : According to local environmental legislation.
ALLERGENS: This product may contain components that may be a potential
risk to allergic reactions. Do not use in case of hypersensitivity signs. For
more information contact Ejendals.
latex free YES NO
ONLY FOR EURASIAN ECONOMIC COMMUNITY CUSTOMS UNION MEMBERS
EJENDALS AB
Limavägen 28, SE-793 32 Leksand, Sweden
Phone +46 (0) 247 360 00 | Fax +46 (0) 247 360 10
info@ejendals.com |
order@ejendals.com |
www.ejendals.com
Declaration of Conformity
www.ejendals.com/conformity
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>