SW-MOTECH TRT00787 Pro Ring Ducati Triumph Instruction Manual
- June 26, 2024
- SW-MOTECH
Table of Contents
ANBAUANLEITUNG
mounting instructions
TRT.00.787.32901/B
contains
TRT.00.787.30600/B
TRT00787 Pro Ring Ducati Triumph
Art.-Nr. / Item No.: TRT.00.787.30600/B| Revision: 00 – Datum / Date: 11 –
2019
---|---
| PRO tank ring
FIDLOCK® licensed technology,
pat.pend; No. 102019215277.5
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
(e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having installation
and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no
liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver! These
mounting instructions are written based on our current state of knowledge.
Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
partsis not guaranteed. Furthermore, BEFORE installing this product, make sure
that all moving parts (e.g. the chain) are in the original state of
maintenance.
Installed accessories can change the behaviour and/or stability of your
vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/
operation as well as TUV regulations if applicable.
If required, register installed parts in the vehicle documents through an
appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that
allitems of the parts list are included. Make sure that your vehicle is parked
safely and cannot fall over. Turn off the engine and remove the ignition key.
Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system. Use appropriate tools. Have another
person to help you.
MOUNTING: All parts and connections removed from the vehicle must be
reinstalled in accordance with the vehicle manufacturers’ specifications or
replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise
specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTECH must be obtained from the vehicle
manufacturer or by a specialist workshop!
FUNCTION CHECK: After installation make sure that all parts and connections
previously removed are properly replaced. Also make sure that no moving parts
are obstructed and no function of the vehicle is hindered in any way. Cables
and hoses must not rub and/or be pinched. Before starting to ride, perform a
comprehensive check of all functions. After the first 50 km and then at
regular intervals, check the tightening torque of all screw connections and
the proper fit of the product.
PARTS LIST
- Allmeasurements in millmeters.
The second number Indicates the ofal quanty o the part i the delvry.
No’torque specificatins: Use the torgue defined by vehicle manufacturer The standard torquei this table can be used 35 long a5 15 withn the vehicle manufacturer s speciications.
Technicaland design modifcatons are subject to change
MOUNTING
Remove the original screws from the mounting points.
ATTENTION: The appropriate screws for mounting must be determined by
yourself, because the depth varies according to the type of motorcycle.
Using too much pressure to tighten the screws and sleeve nuts can damage the
tank ring and gas cap ring Attach the mounting ring (2) to the gas cap ring as
shown.
Then carefully attach the tank ring (1] to the mounting ring (2).
ATTENTION: Use liquid thread locker!
Tighten the screws (3) / (4) with the manufacturers’ specified torque.
Tighten the screws (6] /(7] / (8] and the sleeve nuts (9) as specified
ATTENTION: AFTER installing the tank ring, make sure that the gas cap can
be opened and closed WITHOUT restrictions!
Copyrght by
SW-MATECH GmbH & Co. KG
Technical nd design modification are subject to change.
Packed by:
Date to packaging:
SW-MOTECH GmbH & Co. KG
Ernteweg 7/10
35282 Rauschenberg
Germany
Tel./phone + 49 (0)6425 / 8168 – 050
Fax / fax + 49 (006425 /8168 – 10
info@sw-motech.com
www.sw-motech.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>