Aerpro CAFD01 Infodapter Interface User Guide
- June 25, 2024
- Aerpro
Table of Contents
- CAFD01 Infodapter Interface
- FEATURES
- PRODUCT INFORMATION
- WIRING KEY
- INTERFACE CONNECTIONS
- INSTALLATION GUIDE – WIRING
- STEERING WHEEL CONTROL FUNCTIONALITY
- WIRING DIAGRAM
- CLIMATE CONTROL FUNCTIONALITY
- PARK PILOT – CAMERA FUNCTIONALITY
- CONFIGURATION MENU
- INSTALLER SETTINGS
- CONFIGURATION MENU
- Documents / Resources
Powered by CAFD01
Infodapter Interface
for Ford Ranger SYNC3 vehicles
CAFD01 Infodapter Interface
Note: Application data is subject to change at any time
APPLICATION
Ford Ranger 2016 – 2022
For SYNC3 systems only.
FEATURES
- Allows for the installation of a double DIN aftermarket stereo
- Retains vehicles settings, steering wheel and phone button functionality
- Retains original fitted reverse camera feed
- Generates settings menus, parking sensor audio and graphics
- Provides outputs for Park Brake, Reverse Gear, Speed Pulse and Mute
DISCLAIMER
The information provided in this document is subject to change without notice
due to manufacturer changes and/or improvements to the product/s. This
instruction manual is based on documented data and research. The manufacturer
of this product cannot be held responsible for any changes made to the vehicle
by the manufacturer or damages that may occur through the installation of this
product in accordance with the steps outlined herein.
PRODUCT INFORMATION
The new CAFD01 is a complete installation kit for the Ford Ranger which allows
the user to update their in-car entertainment system to a new aftermarket unit
whilst retaining a whole host of features and functions which would have
previously had been lost with the factory unit. The interface which comes with
the kit not only retains the use of the steering wheel controls, but also
enables the retention of vehicle settings and functions which include the
climate control functionality and display, park pilot functionality, as well
as the original vehicle camera (if vehicle is equipped).
Note: This product is SYNC3 systems only.
WIRING KEY
IN ISO CONNECTOR
Purple | Right Rear Speaker + |
---|---|
Purple/Black | Right Rear Speaker – |
Green | Left Rear Speaker + |
Green/Black | Left Rear Speaker = |
Grey | Right Front Speaker + |
Grey/Black | Right Front Speaker – |
White | Left Front Speaker + |
White/Black | Left Front Speaker – |
Yellow | Permanent 12V |
Black | Ground |
Red | Ignition 12V |
Orange | Illumination |
ADDITIONAL CONNECTIONS
Purple/White | Reverse Gear |
---|---|
Light Pink | Speed Pulse |
Light Green | Park Brake |
Grey | Mute |
Yellow RCA (M) | Reverse Camera Retention |
INTERFACE CONNECTIONS
-
Reverse Camera Extension Harness InputReverse Camera Extension Harness Input
-
Power Harness InputPower Harness Input
-
Head Unit Connection (Patch) Lead InputHead Unit Connection (Patch) Lead Input.
-
DIP Switch 1 – ‘ON’ for Pioneer, ‘OFF’ for other brand head unitsDIP Switch 1 – ‘ON’ for Pioneer, ‘OFF’ for other brand head units
DIP Switch 2 – ‘ON’ for PAL reversing camera, ‘OFF’ for NTSC reversing camera (Default is ‘OFF’/NTSC)DIP Switch 2 – ‘ON’ for PAL reversing camera, ‘OFF’ for NTSC reversing camera (Default is ‘OFF’/NTSC)
DIP Switch 3 – Change from ‘OFF’ to ‘ON’ and back to reset screen settings to factory defaults.DIP Switch 3 – Change from ‘OFF’ to ‘ON’ and back to reset screen settings to factory defaults.
Note: During this procedure, the screen background will change to red and no settings adjustments can be made.
Note: During this procedure, the screen background will change to red and no settings adjustments can be made.
DIP Switch 4 – Not UsedDIP Switch 4 – Not Used -
Not UsedNot Used
INSTALLATION GUIDE – WIRING
See wiring diagram on Pg.4 for more information
Before installing the interface, the factory stereo must be removed and
disconnected. To do this, please consult the vehicle owner’s manual/handbook
or contact a fitting professional.
For universal patch lead, prepare the wiring loops in accordance with the
instruction manual supplied before installation.
-
Connect the 12 Pin connector from the stereo connection (patch) lead to the interface box.
-
Connect the opposite end of the stereo connection (patch) lead to the steering wheel control input on the back of the aftermarket stereo.
NOTE: This may be a 3.5mm jack connector or a wired input depending on the brand of aftermarket stereo being fitted. Please consult the aftermarket stereo installation manual for further information on where to make the connection.
IMPORTANT: THIS STEP MUST BE COMPLETED BEFORE CONNECTING POWER TO THE INTERFACE. FAILURE TO DO SO MAY RESULT IN A LACK OF FUNCTIONALITY AND THE NEED TO REINSTALL THE PRODUCT. -
Connect the 14 Pin connector from supplied wiring loom to the interface box.
-
Connect the power/speaker ISO connector to the power/speaker ISO connector at the rear of aftermarket stereo.
Note: For aftermarket stereos which do not have an ISO connector, please see ‘Wiring Key’ on Pg.2 for information on which wires to connect. -
Connect any additional flying wires from the harness to the head unit as required.
Note: Additional ‘flying’ wires can be connected to the vehicle to support various features i.e. parking brake trigger, reverse gear and speed pulse. Details of these can be found under ‘Additional Connections’. -
Connect 4 Pin camera extension harness to the interface box.
-
Connect the male yellow RCA from the camera extension harness to the reverse camera input of the aftermarket head unit.
7a. To retain the original vehicles reverse camera (if applicable), connect the male yellow RCA from the harness to the female yellow RCA on the camera extension.
7b. To connect an aftermarket reversing camera, connect the male yellow RCA from the camera to the female yellow RCA on the camera extension harness (optional).
Note: Ensure that the ‘Camera Connected’ option in the Preferences menu is set to ‘Yes’ for the camera to function correctly. -
Install the replacement USB connector into the vehicles original location and connect the corresponding ports to the rear of the aftermarket head unit.
-
Attach the antenna adapter in between the vehicles pre-existing black antenna connector (not the white) as well as the rear of the aftermarket head unit.
-
Connect the 24-way connector on the supplied harness to the vehicles original radio connector from the vehicle.
-
Connect the 54-way connector on the supplied harness to the vehicles SYNC3 connector from the vehicle.
-
Test stereo and steering wheel control functionality for correct operation before reassembling the vehicle dashboard. If steering wheel control functions are unresponsive, please uninstall the interface and wiring and reinstall carefully in accordance with the above steps.
USER GUIDE
STEERING WHEEL CONTROL FUNCTIONALITY
The following diagram, though based on careful research, is an example only. Individual steering wheel control configurations may differ. Normal Mode
-
Volume Up
-
Volume Down
-
Speech
-
Mute
-
Track Forward (Short Press)
Hang Up (Long Press) -
Track Back (Short Press)
Pick Up (Long Press) -
Track Back
-
Enter Config Menu (Short Press)
-
Track Forward
-
Seek Forward/Back (Rotation)
-
Volume Up/Down (Rotation)
Enter/Manipulate Climate Control (Short Press/Rotation)
Switch Camera Feed/Park Pilot (Short Press)*
In Configuration Menu
7. Back/Exit Menu
10. Change Current Value (Rotation)
11. Menu Up/Down (Rotation)
Select Current Highlighted Item (Short Press)
To exit the Configuration Menu, select ‘EXIT’ or use button.
- vehicle must be in reverse in order for this function to work.
WIRING DIAGRAM
CLIMATE CONTROL FUNCTIONALITY
The climate control graphics have been replicated and will work like before on
the new aftermarket head unit.
The original climate controls are accessible by single pressing either of the
original buttons on the lower climate panel, or by pressing the Volume Button
(Fig.11).
You can control/toggle select options through a single press of the Volume
Button (Fig.11) or by utilising the preexisting climate button.
The timeout delay of the climate control screen as well as the overlay timing
can altered within the settings menu of the interface.
PARK PILOT – CAMERA FUNCTIONALITY
The park pilot functionality has been replicated and will work like before on
the new aftermarket head unit.
When switching the vehicle into reverse, the vehicles screen will switch to
either the reverse camera or park pilot system (dependent on the selected
setting.
To switch between either park pilot or the reverse camera feed whilst
reversing, simply single press the Volume Button (Fig.11) – the amount of
delay between switching can be altered via the settings menu.
CONFIGURATION MENU
Pressing the ‘Eject Button’ (Fig.8) on the climate control panel will enter
the “Configuration Menu”.
Here you are able to navigate through the various options and settings.
VEHICLE SETTINGS
Within this menu, you are able to alter vehicle settings that would have been
lost if not for the interface. Below is a list of what the interface will
currently retain:
Note: Although care has been taken to ensure the accuracy of this menu structure at the time of printing this document, sudden changes in software by the manufacturer or incompatibilities with the interface cannot be accounted for. Do not consider this list to be exhaustive.
Ambient Lighting
Light Blue
Orange
Blue
Red
Green
Dark Blue
Purple
Brightness (0-100%)| Time/Date
Hours (+/-)
Minutes (+/-)
Day (+/-)
Month (+/-)
Year (+/-)
---|---
Camera Delay
On
Off| Enhanced Park Pilot
On
Off
INSTALLER SETTINGS
The “Installer Settings” menu contains parameters that can be selected to
enhance/adapt the interface layout and functionality.
Screen Size/Position
Allows the user to setup the display screen to the exact/desired size of the
aftermarket stereo being fitted.
Picture Settings
Allows the user to adjust the Brightness, Contrast and Saturation levels of
the menus/parking graphics.
Camera Connected
Select ‘Yes’ if an optional camera is connected.
Video Blanking Time
If the reverse camera or interface image rolls after switching on, or after
switching between the two, adjust this setting to minimise the time taken for
the rolling to stop when switching video signals.
Park Brake Source
Set output to activate when park brake is on (Brake), when speed is less than
3km/h (Speed) or to remain on at all times (Always On).
Ambient Lighting
Select whether the vehicle has pre-existing lighting fitted or not.
CONFIGURATION MENU
Preferences
Reverse Priority
Select which image (Camera or Park Pilot) will be shown by default when
reversing.
(Note: this option is only available when “Camera Connected” is set to
‘Yes’)
Climate Overlay Time
Set the amount of time that the climate control overlays the current screen.
Climate Screen Timeout
Select the amount of time until the climate control screen times out without
any interaction.
Set Time Format
Select time format between AM and PM (12HR and 24HR).
LANGUAGE & VERSION
The latter of the settings menu gives the user a selection of languages –
English/German/French etc. – as well as the ability to view the current
firmware version.
NOTES
Documents / Resources
|
Aerpro CAFD01 Infodapter
Interface
[pdf] User Guide
CAFD01 Infodapter Interface, Infodapter Interface, Interface
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>