SUPERMICRO X10DAi Motherboards User Guide

SUPERMICRO X10DAi Motherboards User Guide

Motherboard Layout and Features

CPU Installation

Heatsink Installation

Insert and tighten the screws in the sequence as shown below.

Front Panel Control (JF1)

Note 1: Graphics shown in this quick reference guide are for illustration only. Your components may or may not look exactly the same as the drawings shown here.

Note 2: For optimized airflow, please follow your chassis airflow direction to install the correct CPU heatsink direction.

Jumpers and Connectors

Jumpers

Connectors

( Note : CPU1 has to be installed.)
CPU2 Slot5| PCI-E 3.0 x16 Slot (This slot is available when CPU2 is installed.)
CPU2 Slot2| PCI-E 3.0 x8 Slot (This slot is available when CPU2 is installed.)
CPU2 Slot4| PCI-E 3.0 x8 Slot (The slots are available when CPU2 is installed.)
PCH Slot6| PCI-E 2.0 x4 in x8 Slot
FAN1-7, FANA| CPU/System Fan Headers
J24| ATX 24-Pin Power Connector (See Warning on Page 1-6.)
JD1| Speaker/Power LED Indicator
JF1| Front Panel Control Header
JL1| Chassis Intrusion
JPII2C1| Power Supply SMBbus I2C Header
JPWR1/JPWR2| 12V 8-Pin Power Connectors (See Warning on Page 1-6.)
JSD1/JSD2| SATA DOM (Device_On_Module) Power Connectors
JSPDIFIn| SPDIF(Sony/Philips Digital Interface)_In Header
JSPDIFOut| SPDIF(Sony/Philips Digital Interface)_Out Header
JTBT1| GPIO Header for Thunderbolt Add-on Card
JTPM1| TPM (Trusted Platform Module)/Port 80 Header
LAN1/LAN2| G-bit Ethernet Ports 1/2
I-SATA0-9| Serial_Link ATA Connections 0-9 supported by Intel PCH
SAS0-3, 4-7 (JS2)| Serial_Link SCSI Connections 0-3, 4-7 supported by LSI SAS Controller
SP1| Onboard Buzzer (Internal Speaker)
STBY1| Standby Power Header
T-SGPIO 1/2/3| Serial-Link General_Purpose IO Headers 1/2/3
USB 5/6 (3.0)| Rear USB 3.0 Ports 5/6
USB 7/8 (3.0)| Rear USB 3.0 Ports 7/8
USB 9/10 (3.0)| Front-accessible USB 3.0 Connections 9/10
USB 0/1| Rear USB 2.0 Connections 0/1
USB 2/3| Front-accessible USB 2.0 Connections 2/3

LED Indicators

Note: Refer to Chapter 1 of the user manual for detailed information on jumpers, connectors, and LED indicators.

CPU Support

Dual Intel® E5-2600v3/v4 Series Processors (Socket R3-LGA 2011); each processor supports dual full-width Intel QuickPath Interconnect (QPI) links (of up to 9.6 GT/s one direction per QPI).

Memory Support

This motherboard supports up to 2048 GB of Registered (RDIMM)/Load Reduced (LRDIMM) ECC DDR4 2133/1866/1600 MHz memory modules in 16 DIMM slots.

Note: Memory speed support is pending on the CPUs installed on the motherboard. For the latest memory updates, please refer to the Tested Memory List posted on our website (http://www.supermicro.com/products/motherboard).

Populating DDR4 RDIMM/LRDIMM Memory Modules

Populating RDIMM/LRDIMM DDR4 Memory Modules for the E5-2600v3- based Motherboard

Populating RDIMM/LRDIMM DDR4 Memory Modules for the E5-2600v4- based Motherboard

Installing DIMM Memory Modules

Back Panel I/O Connectors

Note: Refer to Chapter 2 of the user manual for detailed information on memory support and CPU/motherboard installation instructions.

1. Rear USB 3.0 Port 5
2. Rear USB 3.0 Port 6
3. Rear USB 2.0 Port 0
4. Rear USB 2.0 Port 1
5. SPDIF_Out
6. Surround_Out
7. CEN/LFE_Out
8. Mic_In
9. Line-Out
10. Line_In
11. Gigabit LAN 1
12. Gigabit LAN 2
13. Rear USB 3.0 Port 7
14. Rear USB 3.0 Port 8

© 2018 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or 0in whole is strictly prohibited without Supermicro’s written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing; however, it is not guaranteed.

References

• P65Warnings.ca.gov
• Technologically Advanced High-End Motherboards | Supermicro
• Supermicro Data Center Server, Blade, Data Storage, AI System
• Supermicro Data Center Server, Blade, Data Storage, AI System
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>