saxby lighting 108741 ColtLED CCT Track Head Instruction Manual

June 21, 2024
saxby lighting

Saxby lighting 108741 ColtLED CCT Track Head

Specifications

  • Supply Voltage: 220-240 V~, 50 Hz
  • Bulb Type: 11.7W LED module (SMD) CCT, 2700/3000/4000/6000K

Product Usage Instructions

Wiring:

  1. Undo the screw and remove the cover from the live end.
  2. Push out the desired cable access point and identify the correct cable from the supply.
  3. Connect the supply wires to the terminal block, opposite the corresponding wires from the fitting.
  4. The central connector can also be wired in this way.
  5. Refit the cover onto the live end, taking care not to trap the cable.

Care and Safety:

  • This product is Class 1 and must be connected to earth.
  • Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
  • Caution! Risk of electric shock! This product is not suitable for dimming.

Installation:

  • Existing fittings must be completely removed before installation of a new product.
  • Before removing the existing fitting, carefully note the position of each set of wires.
  • Note that the power at the fuse board and the luminaire must be switched off before installation or maintenance.

Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and satisfactory operation of this product. Please retain these instruction for future reference.

Warning

  • This is a Class 1 product and must be earthed.
  • Please read these instructions carefully before commencing any work.
  • This unit must be fitted by a competent and qualified electrician.
  • Install in accordance with the IEE Wiring regulations and current Building Regulations.
  • Check the pack and make sure you have all the parts listed.
  • To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge.
  • This light fitting should be connected to a fused circuit.
  • If replacing an existing fitting, make a careful note of the connections. Only to be installed outside arms reach.
  • This product is not suitable for dimming.
  • Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

This track system can be extended to a variety of different configurations using accessories such as left bends, right bends, T jucntions, X junctions and flexible joints.

Track Accessory

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.

Note the power at the fuse board and the luminaire must be switched off before installation or maintenance.

  • Plan the track layout and and decide accessories needed before fixing anything to the ceiling.
  • The maximum power per run of track is 1KW (1000W).
  • Ensure the ceiling is capable of holding the weight of the track and products. Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
  • Mark the first hole position and fit the screw in position as shown.
  • Feed the screw through the keyhole slot, and slide into position. Mark the position of the second hole.
  • Locate the track and fit the second screw into position.
  • If fitting accessories, remove the end cap, and push them firmly home. Fit extra lengths of track as required.
  • Locate the product in the track with the connections in the slot. Don’t loosen your hand,
  • Push the buckle tab in place to fix the light in the track firmly.
  • Rotate the switch on the light from OFF to ON.
  • Replace fuse or circuit breaker and switch on. Your light is now ready for use.

Products:

Connection

  • The track accessories are provided with earth connection points on both sides.
  • When offering the accessory to the track, verify which tab needs to be removed.(See left hand diagram).
  • To remove the tab, grasp firmly with a pair of pliers and lever back.
  • The tab should snap cleanly off. (See right hand diagram).
  • Locate the accessory in the track and push home.

Wiring

  • Undo the screw and remove the cover from the live end. Push out the desired cable access point. Indentify the correct cable from the supply and pull through.
  • Connect the supply wires to the terminal block, opposite the corresponding wires from the fitting. The central connector can also be wired in this way.
  • Refit the cover onto the live end taking care not to trap the cable.

Check that…

  • You have correctly identified the wires.
  • The connections are tight.
  • No loose strands have been left out of the connection block.

Technical data

  • Supply Voltage: 220-240 V~, 50 Hz
  • Bulb Type: 11.7W LED module (SMD) CCT, 2700/3000/4000/6000K

This product contains a light source of energy efficiency class E.

SYMBOLS

Care and Safety

  • We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
  • Always disconnect the product from the mains for at least 10 minutes allowing to cool down before any maintenance or adjustment.
  • For your safety, always switch off the power supply before cleaning.

For further information, please visit https://www.lighting-info.co.uk/108741

  • V1 16/09/2023
  • UK Manufacturer: BH17 7BY
  • EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg

www.saxbylighting.com

FAQ

Q: Can this product be dimmed?
A: No, this product is not suitable for dimming.

Q: What type of light bulb does this product use?
A: This product uses an 11.7W LED module (SMD) CCT, with color temperature options of 2700/3000/4000/6000K.

Q: How should I dispose of this product when it reaches the end of its life?
A: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

saxby lighting User Manuals

Related Manuals