SEALEY CST980.V2 Folding Sack Truck Instruction Manual
- June 16, 2024
- SEALEY
Table of Contents
SEALEY CST980.V2 Folding Sack Truck
Product Information
- The 90KG Folding Sack Truck Model No:
- CST980.V2 is a high-quality product manufactured by Sealey.
- It is designed to provide years of trouble-free performance when used according to the provided instructions and properly maintained.
- Please read these instructions carefully and follow the safe operational requirements, warnings, and cautions to ensure the safe and effective use of the product.
- Specifications
- Model No: CST980.V2
- Maximum Load Capacity: 90KG
Product Usage Instructions
- Safety
- Before using the sack truck, it is important to follow these safety guidelines:
- Always load the truck evenly, with the center of gravity of the load as near the center of the truck as possible.
- For large or wide loads, obtain additional support to prevent tipping.
- Do not overload the truck beyond its specified maximum load capacity.
- Do not leave the truck unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.
- Avoid using the truck on uneven ground, curbs, or steps. Use a ramp instead.
- Do not allow others to ride on the truck.
- Do not use the truck if any part is significantly damaged, especially the wheels.
- Introduction
- This section provides a brief introduction to the product but does not contain any specific usage instructions.
- Assembly
- To assemble the sack truck, please follow these steps:
- Make sure the axle is clean from dust and dirt to allow free movement of the wheel.
- Place the sleeve onto the axle as far as it will go.
- Slide the wheel onto the axle and secure it by pushing the pin through the hole at the end of the axle.
- Repeat the operation for the other side.
- Operation
- To operate the sack truck, please follow these steps:
- First, fold down the footplate to prepare it for accepting a load.
- To extend the handle, push the spring-loaded locking bar forward and lift the handle upwards until it latches in its fully extended position.
- To lower the handle, push the spring-loaded locking bar forward and push the handle downwards until it latches in the closed position.
- After use, close the handle, fold up the footplate, and store the truck in a safe dry place.
- Only use the truck with the handle fully closed or fully extended.
- FAQ
- Q: What is the maximum load capacity of the CST980.V2 sack truck?
- A: The maximum load capacity of the CST980.V2 sack truck is 90.
- Q: Can I use the sack truck on uneven ground or run it over curbs or steps?
- A: No, it is not recommended to use the sack truck on uneven ground or run it over curbs or steps. Please use a ramp instead.
- Q: What should I do if any part of the truck is significantly damaged?
- A: If any part of the truck is significantly damaged, especially the wheels, do not use the truck. Please replace the damaged part before using it again.
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
SAFETY
- Always load evenly with the center of gravity of the load as near the center of the truck as possible.
- Obtain additional support for large or wide loads to prevent tipping.
- DO NOT overload the truck – see Specifications.
- DO NOT leave unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.
- DO NOT use the truck on uneven ground and do not run over curbs or steps – use a ramp.
- DO NOT allow others to ride on the truck.
- DO NOT use the truck if any part is significantly damaged – pay particular attention to the wheels.
INTRODUCTION
- The lightweight aluminum frame weighs only 7kg yet has a carrying capacity of 90kg.
- A folding steel foot plate and telescopic handle with spring release means that the trolley can be packed away in seconds.
- Large back support makes light work of oversized loads.
- Fitted with Ø150mm wheels for easy rolling over rough ground. Ideal for business and home use.
SPECIFICATION
- Model no ……………………………………………………..CST980.V2
- Height(s) ………………………………………………….. 710-1080mm
- Overall width …………………………………………………….. 395mm
- Platform depth …………………………………………………… 240mm
- Wheel depth …………………………………………………… Ø150mm
INTRODUCTION
- The lightweight aluminum frame weighs only 7kg yet has a carrying capacity of 90kg.
- A folding steel foot plate and telescopic handle with spring release means that the trolley can be packed away in seconds.
- Large back support makes light work of oversized loads.
- Fitted with Ø150mm wheels for easy rolling over rough ground. Ideal for business and home use.
ASSEMBLY
- Make sure the axle is clean from dust and dirt to allow free movement of the wheel.
- Place the sleeve (fig.1.2) onto the axle (fig.1.1), as far as it will go.
- Slide the wheel (fig.1.3) onto the axle, and complete by pushing the pin (fig.1.4) through the hole in the end of the axle.
- Repeat the operation for the other side.
OPERATION
- Firstly fold down the foot plate ready to accept a load (fig.2).
- To extend the handle push the spring-loaded locking bar forward (fig.2A) and lift the handle upwards until it latches in its fully extended position.
- To lower the handle, push the spring-loaded locking bar forward and push the handle downwards until it latches in the closed position.
- After use close the handle, fold up the footplate, and store it in a safe dry place.
- Only use a truck with a handle fully closed or fully extended.
ENVIRONMENT PROTECTION
- Recycle unwanted materials instead of disposing of them as waste.
- All tools, accessories, and packaging should be sorted, taken to a recycling center, and disposed of in a manner that is compatible with the environment.
- When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.
- Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team at technical@sealey.co.uk or 01284 757505.
- Important: No Liability is accepted for incorrect use of this product.
- Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.
CONTACT
- Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
- 01284 757500
- 01284 703534
- sales@sealey.co.uk.
- www.sealey.co.uk.
- © Jack Sealey Limited
- Original Language
- Version CST980.V2
- Issue: 2 (HF) 21/01/21
- 90KG FOLDING SACK TRUCK
- MODEL NO: CST980.V2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>