ACON X17 Trampoline Enclosure User Manual
- June 22, 2024
- ACON
Table of Contents
ACON X17 Trampoline Enclosure
Specifications
- Product Name : Trampoline with enclosure – ACON X 17
- Manufacturer : ACON Finland OY LTD
- Maximum User Weights
- Low Setting : 80 lb (35 kg)
- Standard Setting : 265 lb (120 kg)
- High Setting : 330 lb (150 kg)
- Height Settings
- 60cm (2 ft)
- 106cm (3.5 ft)
- 120cm (3.9 ft)
Product Usage Instructions
Assembly Instructions
Refer to the manual for detailed assembly instructions. Make sure to follow
the steps carefully to ensure proper setup and safety.
Maximum User Weight
The maximum user weight limit depends on the height setting and the number
of springs installed. Refer to the specifications for the weight limits
corresponding to each height setting.
Adjusting the Bounce
To adjust the bounce feel of your trampoline, you can add springs and
attachment pieces to the mat. Spring kits are sold separately for this
purpose.
Changing the Enclosure Panel
You can change the enclosure panel of your ACON X trampoline to transform
it into an activity center. This allows for a greater range of activities and
keeps the trampoline engaging for everyone.
FAQ
-
Q: Where can I download ACON Trampoline and accessories E-manuals?
- A: You can download the manuals by scanning the QR code provided or visit www.acon-manuals.com for more information.
-
Q: How many height settings does the ACON X 17 trampoline have?
- A: The ACON X 17 trampoline has three height settings: 60cm, 106cm, and 120cm.
Trampoline with enclosure
ACON X 17
User Manual & Assembly instructions: Read carefully prior to assembling the product.
All rights reserved 2023. ACON Finland OY LTD.
All artworks and illustrations are owned by ACON Finland OY LTD. Copying or
reusing them are prohibited by law.
IMPORTANT INFORMATION
Read carefully prior to assembling and using the product. Keep for future
reference.
ASSEMBLY INSTRUCTIONS
ACON
Trampoline and accessories E-manuals & more can be downloaded by scanning the
QR-code or straight from: www.acon-manuals.com
IMPORTANT INFORMATION
- CAUTION! This is an assembly instruction manual for the Acon X 17 Trampoline. Please ensure that you have read and understood the trampoline and enclosure user manual before assembling this product.
- CAUTION! Do not attempt to adjust the height of a fully assembled trampoline. Attempting to adjust the height on a fully assembled trampoline can result in a dangerous structural failure and possible serious injury.
- The owner and/or supervisor of the trampoline is responsible for making all users aware of the practices and information specified in the trampoline and enclosure user manual.
Maximum user weight
The maximum user weight limit of your ACON X trampoline is determined by the
height setting of the trampoline and the number of springs installed. Please
see the MAX USER WEIGHT limits below for the different height settings with
default spring setup (118 pcs).
Adjusting the height
Your ACON X trampoline can be set to three different heights (the highest
setting requires the
X Custom Height Kit, sold separately). The height setting is selected during
the assembly of the trampoline. Pay attention to the assembly steps marked
with the Height System logo during the installation. If you wish to change the
setting afterward, the trampoline must be disassembled by following the
assembly instructions in reverse order up to the point where the height
setting is selected.
Adjusting the bounce
Your ACON X trampoline is equipped with a frame and mat with the ability for a
very wide bounce feel adjustment. The adjustment is made by adding springs and
attachment pieces to the mat
(Spring Kits sold separately).
Changing the enclosure panel
Installation of an accessory panel or replacement of the original panel: Start
by loosening the corner poles at the end of the trampoline where you plan to
replace the panel (instructed in the step 31). Remove the bungee cords and
unzip the bottom of the net (see the steps 29 and 30). Open the vertical
zippers on the panel and remove the bungee cords from the top (steps 21 and
32). Lift the panel down (recommended to be done by two adults) and remove the
poles from the panel. Insert the poles into the new panel and reinstall to the
trampoline in the reverse order.
ACON X FEATURES
Patent pending solutions
Your Acon X is equipped with multiple unique features to improve your jumping
experience and usability of the trampoline
- X PANEL: Exchangeable enclosure panels transform your trampoline into an activity center. Switch out the panels for a greater range of activities! This innovative design ensures that your trampoline remains engaging for everyone.
- MY BOUNCE : The frame features multiple options for spring placement, from number of springs to their location, which creates a unique bounce feel for each setting.
- SMART CORNER : Four adjustable openings, each featuring a waiting platform where people can safely wait outside the jump zone. This feature adds an extra layer of safety and convenience to your trampoline, ensuring a great experience for all users.
- ZERO GAP SAFETY : Zippered connection between the safety enclosure, safety paddings and the frame removes any change of falling out. This secure connection guarantees a worry-free and enjoyable jumping experience for everyone.
- SUPER X FRAME : The rigid base of the Super X Frame removes flex, making it sturdiest ever backyard trampoline frame. This solid construction ensures the durability and reliability of your trampoline for years to come.
- HEIGHT SYSTEM : Adjust the height of your trampoline to three different levels,
to meet the needs of your family as it grows. This adaptable feature allows your trampoline to evolve alongside your family’s requirements, ensuring long- lasting enjoyment.
PARTS LIST
This is a parts list for your product. If any of the parts are missing, please contact ACON customer support.
Place the tubes of the trampoline frame on a soft surface where the trampoline is to be installed.
Assemble the leg. Make sure that the nuts on the crossbars point upwards.
Assemble the U -leg. Position the U-tube so that the holes at the other edge of the tube (c) are on the same side as the top joint socket (a). Align the parts so that all the push button pins are facing upward (b).
The other height setups
- LOW : omit the vertical tube and connect the U-tube (13398) to the top frame (13392).
- HIGH replace the vertical tubes (13426) with the custom height kit tubes (sold separately).
Assemble the upper frame of the short side of the trampoline. NOTE: Pay careful attention to the position of the tubes. Check the correct position by first placing the tubes side by side as shown in the reference figure below, and then align the pipes so that the holes are matched.
Connect the U-leg assemblies with the top frame assembly. Leave the mid leg on the ground between them. Pay careful attention to the orientation of the upper frame assembly to ensure that the spring holes are correctly aligned.
Install the corner support rod (13630), corner support bar (13625), and the protective caps (13605) on the corners of the frame.
Attach the top end of the mid leg to the frame. Make sure that the nuts on the crossbars point upwards.
Attach the center leg to the u-leg. Select the attachment point on the u-leg
according to the height setting. A) Standard, B) Low, C) High (custom height
kit sold separately). Make sure you have completed assembly steps 3 and 4
according to your desired height setting.
- Repeat installation steps 1–5 for the other end of the trampoline. Position the assembled parts at the correct distance from the previously assembled frame end, using the tubes (13417) by placing them on the ground between the halves of the frame.
- Assemble the other end of the trampoline by following the steps 6–9.
Connect the frame ends with tubes (13417). Pay attention to the orientation of the tube.
Place the trampoline mat in the middle with the ACON logo facing up. Attach
the corners of the mat to the trampoline frame with six springs from each
corner (24 in total). Note: The first three springs on each side are installed
in the holes underneath the trampoline frame. Refer to the picture below for
the correct spring holes for the first springs.
CAUTION! Pinch point. Pay careful attention to your hand position when installing the springs.
Install the following springs in the middle of each side of the trampoline (1 spring per the long side and 2 springs per the short side of the trampoline). Note: the springs must be installed in the holes in the top surface of the frame tube.
Continue the spring installation by adding 1 spring in each gap, working clockwise around the trampoline until all the springs have been installed (118 pieces total).
Insert the foam pieces into the pocket under the skirt of the mat and close
the Velcro strips.
Note: If there are two different sizes of foam pieces, use the shorter
ones for the mat’s short end and the longer ones for the long side
Fold the skirt of the mat over the springs on each side.
- Thread the bungee cord through the loops on the edge of the mat. Use the longer bungee cord (13613) on the long side and the shorter one (13608) on short side of the trampoline.
- Attach the bungee cord at the ends to the trampoline frame with Velcro straps (13617).
- Attach the bungee cord from between the mat attachment loops to the trampoline frame with Velcro straps.
Assemble all the enclosure poles (8 in total) by connecting the short and the
long poles together. Note that there are two types of long poles: those with a
bent, silver-colored end
(13439) and those with a straight, black-colored end (13601). Then insert the
foam tubes (30365 and 30364) onto the poles. Finally, detach the end cap by
twisting it until the lock is released.
Slide the enclosure pole sleeve over the pole and the padding. Secure it with the Velcro strip at the bottom.
- Place the enclosure net panels (20690 and 20687) around the trampoline with the ACON logo on each panel facing upward.
- Insert the fiberglass rods into the sleeves on the top of the long enclosure poles. Close the Velcro on the ends of the sleeves.
- Insert the previously assembled enclosure net poles (with the bent tube end) into the sleeves of the short panel with caution. Ensure that the loops at the top of the opening remain outside (you can gently pull them to make the installation easier).
- Fold the loops around the tube.
- Install the previously detached pole end cap.
Lift the short safety net panel with the enclosure poles onto the trampoline as shown in the picture. 1. Attach the long enclosure panel to the short one with the zipper (x4). 2. Insert the ball bungee cord (20170) through the grommets on the top corners of the long and the short panels, and secure it around the pole. Tighten by pulling on the end of the cord.
- Place the previously assembled enclosure poles (with the straight end, 4pcs) against the trampoline frame.
- Insert the ball bungee cord (20170) through the grommets at the top edge of the long panel, and secure around the pole. Tighten by pulling from the end of the cord.
- Wrap the upper Velcro straps on the front of the long panel around the poles. Leave them loosen!
- Attach the threaded rod (13676) to the upper hole at the bottom of the pole.
Carefully lift the corner pole and insert its bent (silver) end into the hole at the corner of the trampoline top frame. At this point, the spring pin (a) should point towards the center of the trampoline, and the pole should tilt in the same direction.
CAUTION! Pinch point. Pay careful attention to your hand position when installing the poles.
Carefully lift the pole next to the pole installed in the previous step, and attach it to the side of the trampoline frame as instructed below. Leave the connection loose, as you are going to install the side plate behind the rubber block (13633) later!
Note: It is highly recommended to ask another person to assist you during this installation step.
Continue installing the poles clockwise around the trampoline until all poles
are installed.
Finally, attach the Velcro strips on the front of the long panel around the
poles but leave them slightly loose to prolong the life of the net.
Install the side plate (13638) behind the rubber block (13633) from both sides. Place the narrower part of the edge of the plate between the bolts in the connection. Tighten the previously installed bolt and nut holding the pole in place.
Install the safety pads on the trampoline. Start by placing the short pads (20542) on the short sides. Then, place the long pads (20548) on the long sides. Align the Velcro strips on both pads. Finally, fit the corner pads (20553) to the corners and attach them to the short and long pads with Velcro
Note: The enclosure is not displayed in the figures for clarity
Insert the safety pad/enclosure mounting hooks (13631) into the spring holes on the top of the frame (32 pcs total). Locate the correct positions for the mounting hooks using the grommets on the bottom edge of the safety net and the safety pad.
Insert the bungee cord (20598) through the grommet at the bottom edge of the safety pad and the enclosure net panel (total 32 pcs). Pay careful attention to the corner areas where the bungee cord should pass through multiple grommets/layers (please refer the figure below).
- Attach the enclosure panel to the safety pad by closing the zipper (6 pcs).
- Attach the bungee cord to the mounting hook (32 pcs).
Tighten the enclosure by rotating the corner pole with the special tool (30448) until the spring pin on the corner post locks into the trampoline frame. Attach the Velcro strip at the bottom of the long panel to the corner pole. Repeat for all the corners.
Select the corner(s) you want to be the access point on your trampoline (1–4 corners).
- Detach the two outermost bungee cords from the bottom of the net. Open the zipper up to the 2nd grommet.
- Open the vertical zipper up to one of the strap loops (different height options for the opening).
- Install the attachment loop between the short and the long panel from below the zipper.
- Attach the quick-release buckle (20677) to the crossbar (installed in step 7) at the corner where you are setting up the entrance.
- Attach one side of the fabric piece (20731) under the corner padding and the other side to the bottom of the long panel on the inside using its Velcro straps.
- Fasten the door with the buckle and adjust the tension by changing the attachment point of the Velcro strap if necessary.
Install the cover plates (13682 and 13412) on top of the middle legs.
ENSURE THAT NO UNDERGROUND UTILITIES, SUCH AS ELECTRICAL CABLES, ARE PRESENT WHERE YOU INSTALL THE ANCHORS. Screw the anchor into the ground as shown below. Tie the strap of the anchor set around the upper frame of the trampoline. Attach the hook into the loop of the anchor base. Tighten with the ratchet.
Attach the safety instructions sign next to the entrance around the trampoline
frame or to the safety net with the cable tie provided.
Your ACON X 17 is now ready for use. Have fun!
DO NOT use the trampoline without the safety pad (b). The safety pad is designed to reduce the possibility of injury by protecting the user from coming into contact with the frame (e) and springs (g) of the trampoline. It is very important that you properly and securely attach the safety pad and the enclosure net (a) to the attachment hooks (f) with the bungee cords (d), and that they are in the correct position prior to using the trampoline. Ensure also that all the zipper connections between the safety pads and the enclosure are always properly closed.
CONTACT US
USA
Email: customercare.us@acon24.com
Tel: +1 (866) 297 5234
us.acon24.com
CANADA
Email: customercare.ca@acon24.com
Tel: +1-866-297-5234
ca.acon24.com
SWEDEN
Email: kundtjanst@acon24.se
Tel: +46 (08) 12013113
www.acon24.se
EUROPE
Email: customercare.eu@acon24.com
acon24.com
FINLANDhtt
Email: acon@acon.fi
Tel: +358 (0)9 42720823
acon.fi
GERMANY
Email: customercare.de@acon24.com
Tel: +49 302 084 7588
de.acon24.com
FRANCE
Email: customercare.fr@acon24.com
Tel: +33 184 888 762
fr.acon24.com
All rights reserved 2023. ACON Finland OY LTD.
All artworks and illustrations are owned by ACON Finland OY LTD. Copying or
reusing them are prohibited by law.
References
- Acon - Liikkumisen iloa ja aktiivista aikaa yhdessä. – Acon.fi
- ACON EU – Trampoline Shop online - trampolines and airtracks – Acon EU
- Shop trampolines, rebounders and airtracks online - ACON CA – ACON CAN
- ACON DE – Online-Trampolin-Shop – Trampoline und airtracks – ACON Germany
- ACON FR - Boutique de trampolines en ligne - Trampolines et Airtrack – ACON France
- Trampolines - Rebounders - Airtracks - ACON USA
- ACON Instruction manuals & guides
- ACON SVERIGE – webbshop – Studsmattor och Airtracks – Acon24.se
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>