ACON AIR 16 HD Trampoline with Enclosure Instruction Manual
- June 12, 2024
- ACON
Table of Contents
ACON AIR 16 HD Trampoline with Enclosure
Product Information
- x2 – L-tube for mid leg
- x4 – Leg extension for mid leg
- x2 – Jumping mat
- x4 – Spring
- x2 – Safety pad, short
- x36 – Bolt assembly, trampoline
- x2 – Bungee cord, Safety pad
- x4 – Side pole, lower
- x8 – Pole, upper
- x8 – Pole foam, lower
- x8 – Pole foam, upper
- x1 – Sleeve for enclosure pole
- x8 – Cap
- x8 – Net
- x2 – Ball bungee cord, net
- x1 – Bolt assembly, enclosure
- x1 – Adjustable strap, enclosure
- x1 – Anchor kit
- x1 – Safety instructions card
- x1 – Allen key
- x1 – Wrench
Product Usage Instructions
- Attach 2 L-tubes for mid leg
- Attach 4 leg extensions for mid leg
- Place 2 jumping mats
- Attach 4 springs
- Install 2 short safety pads
- Secure the trampoline with 36 bolt assemblies
- Use 2 bungee cords to attach safety pads
- Attach 4 side poles, lower
- Install 8 upper poles
- Place 8 lower pole foams
- Attach 8 upper pole foams
- Use 1 sleeve to cover the enclosure pole
- Secure the poles with 8 cap
- Install the net using 8 ball bungee cords.
- Use the bolt assembly to secure the enclosure.
- Adjust the enclosure using the adjustable strap.
- Set up the anchor kit
- Refer to the safety instructions card
- Use the provided Allen key
All rights reserved 2022. ACON Finland OY LTD.
Assembly instructions & Product specifications
CAUTION: This is an assembly instruction manual for Aeon AIR 76HD
Trampoline. Ensure that you have read and understood the trampoline user
manual before assembling this product.
The owner and/or supervisor of the trampoline are responsible for making all
users aware of the practices and information specified in the trampoline user
manual.
ACON Trampoline E-Manuals & more can be downloaded by scanning the QR-code
below or from: www.acon-manuals.com/trampoline-manuals
PARTS LISTS
This is a parts list for your trampoline. If any of the parts are missing, please contact ACON customer support.
TRAMPOLINE
ENCLOSURE
OTHER & TOOLS
Assemble mid legs. NOTE: lock nut is supposed to stop after a few twists while hand tightening.
Steel plates (#3) are purposely a tight fit to install because they play a role in the structural integrity and performance of the trampoline.
Tips to install steel plates (#3):
- Make sure that you have not tightened the nuts in step 7. At this point, only twist the lock nuts on the bolts by hand, and do not tighten with a wrench.
- Make sure that the orientation of steel plate (#3) is correct-see the direction of the bends in the ends (turned away from the bottom of the leg assembly).
- Install one outer bolt first, and only barely hand tighten the nut. Then, install the outer bolt in the opposite end-it may help if you bow the steel plate slightly to better align the bolt holes. Also squeezing/ bending the mid leg assembly by pulling/ pushing in the directions shown in figure below may help. The easiest way to do that is to turn the leg assembly upside down against the ground and press down from the center. Hand tighten only.
- Proceed to install the inner bolts.
Tighten the bolts with a wrench (#32) and alien key (#37). Do not tighten the vertical connections yet. Add the plastic protective caps. DO NOT USE POWER TOOLS.
Assemble trampoline ends. NOTE: lock nut is supposed to stop after a few twists while hand tightening.
Connect the trampoline ends with top frame tubes (#7).
Please note that the sides of the frame won’t be straight at this point. They
are pulled into their final positions after the springs are installed.
SKIP THIS STEP IF INSTALLING TRAMPOLINE ONLY.
CAUTION! INCORRECTLY INSTALLED PART CAN CAUSE INJURY!
Please see the figure below on instructions to align the spacer between the
enclosure pole and trampoline leg (arrows up and facing the enclosure pole).
DO NOT USE POWER TOOLS.
SKIP THIS STEP IF INSTALLING BOTH TRAMPOLINE AND ENCLOSURE TO GETHER.
Connect springs (#1) to the v-rings of the mat (#10) and pull towards yourself with the spring pull tool to connect to frame.
CAUTION! PINCH PONT.
Pay attention to hand position when handling springs.
Connect springs (#11) to the v-rings of the mat (#70) and pull towards yourself with the spring pull tool to connect to frame.
CAUTION! PINCH PONT. Pay attention to hand position when handling springs.
Continue the spring installation by adding l spring in each gap, working clockwise around the trampoline until all the springs have been installed
CAUTION! PINCH PONT. Pay attention to hand position when handling springs .
1 spring/ lap/ gap
Attach safety pads (#13 and #12) to the frame with bungee cords (#15).
Tip: using spring pull tool is helpful. If necessary, loosen the upper bolt of the enclosure pole slightly when placing the skirt of the safety pad between the enclosure pole and frame. REMEMBER TO RE-TIGHTEN.
Assemble all enclosure poles as instructed below.
NOTE: Sliding the sleeve (#22) over the cap can be a tight fit. Connect
the assembled poles in to the lower poles.
Attach the short sides of the net first. Adjust the lower edge of net to the centerline of safety pad as instructed in fig. 1 with adjustable straps (part
27). The door opening can be placed on the short or the long side of the
trampoline.
ENSURE THAT NO UNDERGROUND UTILITIES SUCH AS ELECTRICAL CABLES ARE PRESENT WHERE YOU INSTALL THE ANCHORS. Screw the anchors (#28)into the ground as instructed below. Fig. 2: Tie the strap of the anchor set over the upper frame of the trampoline. Attach the hook into the loop of the anchor base. Tighten with the ratchet.
Your ACON AIR 16 HD is ready for use. Have fun!
ACON AIR 16 HD
Product dimensions and ASTM /CE-certified weight limits:
WARNING! maximum user weight: 330 lb (150 kg)
CONTACT US
EUROPE
Email: customercare.eu@acon24.com
acon24.com
USA & CANADA
Email: customercare.us@acon24.com
Tel: +1 (866) 297 5234
us.acon24.com
SWEDEN
Email: kundtjanst@acon24.se
Tel: +46 (08) 12013113
www.acon24.se
FINLAND
Email: acon@acon.fi
Tel: +358 (0)9 42720823
acon.fi
All rights reserved 2022. ACON Finland OY LTD.
All artworks and illustrations are owned by ACON Finland OY LTD.
Copying or reusing them are prohibited by law.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>