muse MH-08 MB Solar Radio User Manual

: June 21, 2024
: muse

muse MH-08 MB Solar Radio

USER MANUAL

MODEL: MH-08 MB

Read the instructions carefully before operating the unit.

LOCATION OF CONTROLS

1. Light button
2. Alert button
3. Solar panel
4. Power ON/OFF ; To select between FM, Bluetooth and AUX mode
5. PLAY/ PAUSE; Time setting; Auto Preset; Disconnect the paired Bluetooth device; Stereo Pairing
6. : Receive call/ Transfer call/ End call
7. : Tuning; setting up/ down; To select desired track (Bluetooth mode)
8. LCD display

1, 2, 3, 4, 5 : To recall preset station 1,2,3,4,5
10. Bulit-in Microphone
11. Shoelace holder
12. Hand crank
13. NFC tag
14. Telescopic antenna
15. Flashlight
16. button: To adjust the volume
17. : USB-C port for charging the built-in battery
18. : AUX IN jack (3.5MM)
19. : USB-C port for charging the external device

POWER SUPPLY

The unit is powered by a built-in, lithium-polymer rechargeable battery.

USB CHARGING

To charge the internal battery, connect the smaller end of the supplied USB cable to the USB-C port and the other end to a powered USB jack on your computer or an AC power supply (not included).
Charge the built-in battery for at least 3 hours before using the device for the first time.
The battery indicator will stop blinking when it becomes fully charged.

Warnings:

The battery level will be shown on display: .
Recharge the built-in battery when you are ready to use it again.
While using the built-in battery, the environmental temperature should be 5°C (41°F) to 35°C (95°F).
To get the longest service life of the built-in battery, charge at indoor-temperature.
The built-in battery in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, heat above 100°C (212°F), or incinerate.
The unit should not be exposed to excessive heat such as sunshine, fire or the like.
When discarding the unit, environmental problems must be considered and local rules or laws governing the disposal of such products must be strictly followed.
When the built-in battery power is low, “ ” will show on display.

Notes:

– The unit is supplied from limited power sources.
– The unit is designed with a thermal protection system. When the unit’s operation temperature exceeds 45°C, it will stop charging the built-in battery automatically for protection. In this case, await the unit to cool down to resume normal.
– To maintain the battery performance, fully charge it at least every 3 months when the unit is not used for a long time.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

OTHER CHARGING MODES

Solar charging and dynamo charging can provide assistance when you need electricity for outdoor operations and emergency situations.

Solar charging

1. Put the unit in the sunlight. Ensure that the solar panel of the unit is irradiated directly by the sunlight. The unit will charge the built-in battery automatically.
2. While charging, the battery level will be shown on display: .

Dynamo charging

1. Turn the hand crank, and the built-in dynamo will start to generate electricity. The unit will charge the built-in battery automatically.
2. While charging, the battery level will be shown on display: ..

Note: When using the hand crank for charging, maintain a stable speed and directional turning. Do not force a sudden reversal during rotation, which may damage the dynamo and shorten its lifespan.

USING THE FLASHLIGHT

Press button to turn on the flashlight. Press again to turn off the flashlight.

USING THE ALERT LIGHT AND SIREN

Press , once, the alert light will be on.
Press , twice, the alert light will be on with siren.
Press , again to turn off the alert light and siren.

Note: You can use the Flashlight, Alert light and Siren in any mode.

TURNING UNIT ON/OFF

Press button once to turn on the unit.
Press and hold button again to turn off the unit.
Note: When using the unit for the first time, press and hold to turn on the unit

SELECTING FUNCTION

When the unit is ON, press button repeatedly to select FM, Bluetooth or AUX mode.

SETTING THE TIME

1. In standby mode, press and hold button to enter time setting mode and the hour digits flash.
2. Press to adjust the hour value. Press to confirm and minute digits flash.
3. Press to adjust the minute value and press again to confirm.

NOTE:

– If during the adjustment time no key is activated in 10 seconds, the current display will be automatically stored.
– In standby mode, the display will turn off if no key is activated in 10 seconds. If you need to check the clock time, press and hold any key on unit.

LISTENING TO THE RADIO

When the unit is ON, press button repeatedly to select FM mode. “FM” will be shown on display.

MANUAL SEARCH

1. Choose your radio station with .
2. Adjust the volume to desired level.

AUTOMATIC SEARCH

Press and hold . The automatic search locates strong stations. A station with a weak signal can be set manually by repeatedly pressing .

Note: During the search operation, the sound level is automatically muted.

To enhance radio reception ability:
Extend the telescopic antenna.

PRESET STATIONS

This unit can store 5 FM stations.
1. In FM mode, select a desired radio station with .
2. Press and hold 1,2 3,4 5, , button to store the station in preset channel 1/2/3/4/5 respectively.

AUTO PRESET

Press and hold to start automatic preset programming. Radio frequencies will be browsed and radio stations stored automatically. When all the available radio stations are stored or all memory locations are full, the auto preset programming function will stop.

Note: During the search operation, the sound level is automatically muted.

LISTENING TO RADIO PRESETS

Press 1, 2 ,3, 4,5 , button respectively to recall the stations in preset channel 1/2/3/4/5 simply.

BLUETOOTH FUNCTION

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by New One S.A.S is under license. Other trademarks and trade names are those of their respective owners.

Pairing a Bluetooth Device

1. When the unit is ON, press button repeatedly to select Bluetooth mode. The display will show “ bt ” for a few seconds. The Bluetooth indicator will start to blink slowly, indicating it is in pairing mode.

2. On the Bluetooth device, enable Bluetooth and select “MUSE MH-08 MB” from the Device List. (Refer to the user manual of the device to be connected for detailed operations.) If the Bluetooth device prompts for a pass code, use “0000”. Some Bluetooth devices will ask you to accept the connection. If the units are paired properly, you will hear the indication sound. The Bluetooth indicator will remain on.

Tip: If you want to connect your Bluetooth speaker to another Bluetooth audio device, press and hold button to disconnect the current device, and then follow the steps above to make a new connection.

On some devices such as computers, once paired you must select the unit from the Bluetooth menu and choose “Use as Audio Device (stereo)” or similar.
Pairing remains intact when the unit and/or your Bluetooth device is taken out of communication range. An active connection will be re-established when your Bluetooth device returns within range.
When the unit is turned on again, it will automatically try to reconnect with the most recently paired Bluetooth device.

Hereby, NEW ONE S.A.S, declares that this MUSE MH-08 MB is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The declaration of conformity may be consulted at www.muse- europe.com.

Using a Bluetooth Device

With a unit paired (see previous section), operate your Bluetooth device and its sound will be heard through the MH-08 MB’s speaker.

1. Press the button to pause playback. Press again to resume playback.
2. Select desired track with .
3. Adjust the volume level by the volume knob . You can also adjust the volume on the device to which you are paired.

Receiving / Ending a Phone Call

This unit is equipped with a built-in microphone, which allows you to make or end calls of a connected mobile phone through this unit. Make sure your Bluetooth-enabled mobile phone is paired with the unit. When there is an incoming call to the connected mobile phone, you will hear an incoming call alert tone from the unit.

1. Press the button to answer the incoming call.
2. Press the button again to end call.
3. To reject the incoming call, press and hold button.
4. To redial the last number retained in the memory of the mobile phone, press the button twice.

Notes:

Re-dialing function is unavailable if there is no dial record feature in your mobile phone.
This unit will not operate or may operate improperly with some Bluetooth mobile phones/ audio players.
If the conversation is not clear, try to move closer to the microphone (located at front behind the speaker grill).

Using a NFC Device

NFC (Near Field Communication) is a technology that enables short-range wireless communication between NFC-enabled devices, such as mobile phones

1. When the unit is ON, press button repeatedly to select Bluetooth mode. The display will show “ BT ” for a few seconds. The Bluetooth indicator will start to blink slowly, indicating it is in pairing mode.
2. Enable NFC and Bluetooth on your Bluetooth device (see the user manual of your device for details), tap the NFC device on the NFC tag of this unit. If the units are paired properly, you will hear the indication sound. The Bluetooth indicator will remain on. The NFC device is connected to this unit via Bluetooth.
3. Select and play audio files or music on your NFC device.
4. To break the connection, tap the NFC device with the NFC tag on this unit again.

Notes:

– The operational range between the main unit and a NFC device is approximately 10 meters.
– The NFC tag is located at the back of unit. Pull up the hand crank before making NFC connection/ disconnection.

STEREO PAIRING

This function makes it possible for you to get stereo surround sound quality. It requires two Bluetooth speakers MH-08 MB to realize the real Bluetooth radio channel wireless separation, therefore, you’ve got to purchase two MH-08 MB.
Tips: It is suggested that the distance between the main speaker and secondary speaker is within 4 meters.

muse MH-08 MB Solar Radio_

1. Turn on the two Bluetooth speakers MH-08 MB.
2. When both speakers are in pairing mode, press twice on one Bluetooth speaker which will become the main speaker (L channel), then it will search and connect to the secondary speaker (R channel). “ ” will be displayed. They will recognize the left and right channel automatically.
3. Connect your main speaker to Bluetooth enabled device (e.g. smart phone).
4. Play your song and listen to the sound in stereo.
5. Press button on either speaker to pause playback. Press again to resume playback.
6. Press twice on either speaker to disconnect the stereo pairing.

CONNECTING AUXILIARY SOURCE

1. Connect your auxiliary source (e.g. mp3 player) to the AUX IN jack on the unit (cable not included).
2. When the unit is ON, press button repeatedly to select AUX mode.
” RU ” will be shown on display.
3. Start playback from your auxiliary source.
4. Adjust the volume to desired level.
5. To stop playback, disconnect your auxiliary source from the AUX IN jack .

CHARGING THE EXTERNAL DEVICE

This unit is equipped with a built-in USB-C charging port (Output: 5V========== 1A) for recharging your mobile device (e.g. Smartphone, tablet, etc.)
Simply plug the USB-C charging cable (not included) into the USB-C charging port and connect it to your mobile device.

RESET

Press and simultaneously for 2 seconds to restore to factory default settings.

Note: When using the unit for the first time after resetting, press and hold to turn on the unit.

INSTALLING THE SHOELACE

1. To Insert the shoelace into the cavity, use a pin/ stick to pull the shoelace out through inside.
2. Tie a knot in the shoelace.

muse MH-08 MB Solar Radio

SPECIFICATIONS

RECHARGEABLE BATTERY

Battery Type: 3.7V 1800mAh Lithium -polymer Battery
Charging power: DC 5V 2.5A
Operating Time: Approx. 6 hours at 50% volume after fully charged
Charging Time: Approx. 3 hours
RADIO: FM: 87.5 -108 MHz

BLUETOOTH

Bluetooth: 2.402-2.48GHz
RF Output Power: +6 dBm
Bluetooth Version: V5.1+EDR
Working Distance: Up to 10 meters measured in open space (wall and structures may affect range of device)

Specifications are subject to change without notice.

SAFETY INSTRUCTIONS

– The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table-cloths, curtains, etc.
– No naked flame sources, such as lighted candles, should be placed on the apparatus.
– The use of apparatus in moderate climates.
– The apparatus should not be exposed to dripping or splashing.
– Ensure a minimum distance of 5cm around the apparatus for sufficient ventilation.
– Do not place objects filled with liquids, such as vases, on the apparatus.
– The marking plate is located on the bottom of unit.
– Do not throw batteries into fire! Respect the environment when disposing of used batteries.
– Batteries should not be exposed to excessive heat such as sunshine, fire or other similar heat source.
– Under the influence of electrical fast transient or/ and electrostatic phenomenon, the product may malfunction and require user to power reset.
– The normal function of the product may be disturbed by strong Electro- Magnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual. In case the function could not resume, please use the product in other location.

NEW ONE S.A.S
10, Rue de la Mission, 25480 Ecole Valentin, France