ENERGETIC E3DL Series 6 inch CCT Selectable Recessed Downlight Installation Guide

June 16, 2024
energetic

ENERGETIC E3DL Series 6 inch CCT Selectable Recessed Downlight

ENERGETIC-E3DL-Series-6-inch-CCT-Selectable-Recessed-Downlight-
PRODUCT

Product Information

Specifications

  • Model : E3DL series 6-inch CCT Selectable Recessed Downlight
  • Color Temperatures : Soft White (2700K), Warm White (3000K), Cool White (4000K), Daylight (5000K), Cool Daylight (6500K)
  • Dimming: Smooth dimming to 10% of full light levels with most dimmers

Product Usage Instructions

Installation Instructions

  1. Open the clip as shown in Fig 1.
  2. Ensure the power is turned off. Screw the adapter into the existing socket in the base for either 5 or 6-inch cans, adjusting the spring clip arms accordingly.
  3. Set the desired color temperature (CCT) using the slide switch on the back of the housing. Choose from 2700K to 5000K.
  4. Squeeze the two sets of spring clip arms towards each other and install the downlight into the can by hooking them into the arm hooks on the inside walls. Push the downlight up until flush against the ceiling.

Care and Maintenance Clean with a mild, non-abrasive glass cleaner and a soft cloth. Avoid solvents or cleaners with abrasive agents. The power should be off during cleaning.

Troubleshooting

Problem Possible Solution Corrective Action
The fixture does not light. 1. Check if the power is off. 2. Verify wire

connections. 3. Test
wall switch.| 1. Check the circuit breaker or wall switch. 2. Inspect wire
splices. 3. Replace defective switch.
The circuit breaker trips when light is turned on.| Crossed wires or power wire is grounded out.| Verify correct wire connections.

FAQ

  • Q: Can this downlight be used with any dimmer?
    • A: Yes, this downlight can be used with most dimmers for smooth dimming to 10% of full light levels.
  • Q: How do I change the color temperature of the downlight?
    • A: To change the color temperature, use the slide switch on the back of the housing to select from 2700K to 5000K.
  • Q: How should I clean the downlight?
    • A: Clean with a mild, non-abrasive glass cleaner and a soft cloth. Do not use solvents or cleaners containing abrasive agents, and ensure that power is turned off during cleaning.

PACKAGE CONTENTS

ENERGETIC-E3DL-Series-6-inch-CCT-Selectable-Recessed-Downlight-FIG
\(2\)

CAUTION:

The fixture body is one piece. Do not disassemble it. This unit is intended for indoor use only.

DIMMER COMPATIBILITY

This downlight can be used with most dimmers to create your desired ambiance with smooth dimming to 10% of full light levels.

INSTALLATION INSTRUCTION

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product. Failure to do so could lead to electric shock, fire or other injuries that could be hazardous or even fatal.
Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTICE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help. WARNING

Minimum Lamp Compartment Dimensions 5.51-in. (Diam) x 7.4-in. (H) Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Disconnect power at fuse or circuit breaker before installing or servicing. No user-serviceable parts inside. To avoid electrical shock, do not disassemble the product. This product is not intended for use in emergency light fixtures or exit signs. Not for use where exposed directly to the weather or water. This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm.
Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings.

To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
Installers should not disconnect existing wires from lamp holder terminals to make new  connections at lamp holder terminals. Instead, installers should cut existing lamp holder leads away from the lamp holder and make new electrical connections to lamp holder leads wire by employing applicable connectors.

INSTALLATION INSTRUCTIONS

  1. Open the clipENERGETIC-E3DL-Series-6-inch-CCT-Selectable-Recessed-Downlight-FIG \(3\) ENERGETIC-E3DL-Series-6-inch-CCT-Selectable-Recessed-Downlight-FIG \(4\) ENERGETIC-E3DL-Series-6-inch-CCT-Selectable-Recessed-Downlight-FIG \(5\)
  2. Make sure the power is turned off, Screw the adapter in a luminaire(A)into an existing socket in the base.
  3. Adjust Spring clip arms (AA) to fit either 5” or 6” inches by screwing in screws (BB) at the demonstrated location on Fig.2. for desired can size.
  4. Before proceeding to the next step, set the desired color temperature (CCT), using the slide switch on the back of the housing. CCT can be changed from 2700K (soft white), 3000K (warm white), 3500K (natural white), 4000K (cool white), 5000K (daylight).
    • 4. Squeeze the two sets of spring clip arms up towards each other and proceed to the next step to install the downlight into the can.
  5. Carefully route wires into can fixture and hook both sets of spring clip arms into the arm hooks on the inside walls of the can, once secured inside the hooks, release the spring clip arms and gently push the downlight (B) up into the can until flush against the ceiling surface.

CARE AND MAINTENANCE

Clean with a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure the power is turned off, and any liquid spray should be applied to the cleaning cloth and not sprayed directly onto the fixture itself.

TROUBLESHOOTING

ENERGETIC-E3DL-Series-6-inch-CCT-Selectable-Recessed-Downlight-FIG
\(6\)

Documents / Resources

| ENERGETIC E3DL Series 6 inch CCT Selectable Recessed Downlight [pdf] Installation Guide
E3DL56, E3DL Series 6 inch CCT Selectable Recessed Downlight, E3DL Series, 6 inch CCT Selectable Recessed Downlight, CCT Selectable Recessed Downlight, Selectable Recessed Downlight, Recessed Downlight, Downlight
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

energetic User Manuals

Related Manuals