ENERGETIC LIGHTING E4WPA Series Wall Pack Fixture Instruction Manual

June 4, 2024
Energetic Lighting

ENERGETIC LIGHTING E4WPA Series Wall Pack Fixture

ENERGETIC LIGHTING E4WPA Series Wall Pack Fixture

PACKAGE CONTENTS

ENERGETIC LIGHTING E4WPA Series Wall Pack Fixture
1 ENERGETIC LIGHTING E4WPA Series Wall Pack
Fixture 2

SAFETY INFORMATION

  • Please read and understand this entire manual before attempting to assemble, operate or install the product.
  • Failure to do so could lead to electric shock, fire or other injuries that could be hazardous or even fatal.
  • Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
  • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  • This product must be installed in accordance with local, state and national electrical codes.
  • Installation work shall be completed by a licensed installer that is familiar with the construction and operations of the product.

CAUTION:
This product can only be dimmed with standard 0-10v low voltage dimming systems.

INSTALLATION INSTRUCTIONS

ENERGETIC LIGHTING E4WPA Series Wall Pack
Fixture 3

  • Open fixture housing by removing two (2) screws located on hardware reference
  • Release quick disconnect on wires between LED driver and front lens cover housing
  • Open the front lens cover housing from back fixture base by lifting the right to open from the connecting joints on the left.
  • Unscrew center twist out cover to allow building wires to pass through into the housing
  • Function box mounting: Drill out the matching set of holes on the cast pattern that aligns properly with the screw positions on the existing building junction box (not provided)
  • Direct mount to the surface: Drill out the three (3) cast pattern hole locations as shown in the diagram above, use the back fixture base as a template and transfer hole locations to the desired mounting position. Ensure appropriate mechanical support is provided by mounting surface material, use anchors if necessary (not provided).
  • Use wire nuts to connect the appropriate input leads as shown in the following section.
  • Connect optional low voltage DC dimming wires if desired, otherwise, leave insulated.
  • Reassemble by a reverse process in Step 2 and then Step 1 above to complete the installation and test with power to ensure a working Texture.

WIRING DIAGRAM

ENERGETIC LIGHTING E4WPA Series Wall Pack Fixture
4

CARE AND MAINTENANCE

Clean with a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure the power is turned
off, and any liquid spray should be applied to the cleaning cloth and not sprayed directly onto
the fixture itself.

TROUBLESHOOTING

ENERGETIC LIGHTING E4WPA Series Wall Pack Fixture
5

WARRANTY

This fixture is warranted to perform free from defects for five years. If it fails to do so, you may return it with proof of purchase to 13445 12th St., Chino, CA 91710 for replacement.

FCC RULES

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  •  This device may not cause harmful interference, and
  •  this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Energetic Lighting User Manuals

Related Manuals