Hoover HDSVI985B 90cm Island Cooker Hood User Manual

Hoover HDSVI985B 90cm Island Cooker Hood User Manual

INTRODUCTION

Thank you for choosing this cooker hood.
This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance. In order to operate the unit correctly and safety, please read this instruction manual carefully before installation and usage. The cooker hood uses high quality materials, and is made with a streamlined design. Equipped with large power electric motor and centrifugal fan, it also provides strong suction power, low noise operation, non-stick grease filter and easy assembly installation.

By placing the marking on this product, we declare, on our own responsibility, compliance to all of European safety, health and environmental requirements stated in the legislation for this product.

SAFETY PRECAUTION

• Never let the children operate the machine.

• The cooker hood is for home use only, not suitable for barbecue, roast shop and other commercial purpose.

• The cooker hood and its filter should be clean regularly in order to keep in good working condition.

• Clean the cooker hood according to the instruction manual and keep the unit from danger of burning.

• Forbid the direct baking from the gas cooker.

• Please keep the kitchen room a good convection.

• Before connecting this appliance check that the power supply cord is not damaged. A damage supply cord must be replaced by qualified service personnel only.

• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels;

• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels;

• Regulations concerning the discharge of air have to be fulfilled.

• This appliance if not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person slide for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Do not flame under the range hood.

• The range hood is not intended to be installed over a hob having more than four hob elements
  Electrical Shock Hazard

• Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer.

• Failure to follow these instructions can result in death, fire, or electrical shock.

Standard Installation Accessories List

CEILING MOUNTING INSTALLATION

1. Position the hanging plate on the ceiling and then mark the position of the screw holes. The hanging plate should be securely fixed to the ceiling,
   • 11 x ST6 (40 mm)screws for wooden ceiling
   • 8 x expansion bolts for cement ceiling

2. Fix the angle bars to the hanging plate, using the 8 x M5 screws.

3. Extend the angle bars to the repaired height and then fix them in position using the 16 x M5 screws and nuts with metal washers.

• IMPORTANT: The angle bars must have an overlap of AT LEAST 100 mm.

4. If your cooker hood is going to be used in extraction mode, then you should connect the ducting hose to the ceiling adaptor at this point. Fix the upper chimney section to the hanging plate, using the 4 x self tapping screws.
   Slide the lower chimney section onto the angle bars and raise it until it sits just below the upper chimney section.

5. If the glass canopy has not been pre-assembled by the factory, then it should be fixed to the top of the main body of the cooker hood at this stage.

6. Lift the main body of the cooker hood onto the angle bar and then fix it into position using the 16 x M5 screws.
   • IMPORTANT: This stage of the installation process MUST be completed by two people.
   • IMPORTANT: The 16 x M5 screws MUST be securely tightened.

7. If you are going to be using the hood in extraction mode, you should fix the ducting hose to the spigot.

• The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood. The appliance should now be connected to the electrical supply.
• Check that the appliance is operating correctly by selecting each speed and switching the light bulbs on and off.
• Remove the hanging hook and then slide the lower chimney section downwards, until it rests against the main body of the cooker hood.
• Use a stainless steel cleaner and polish on the stainless steel sections of the appliance.
• If you are using the appliance in recirculation mode, then you should now fit the carbon filter.

DESCRIPTION OF COMPONENTS

STANDBY MODE.
After plug in, all lighting, system in STANDBY MODE.

1 Low Speed button
It’s used for Ventilation on the kitchen. It is suitable for simmering and cooking which do not make much steam.

2 Medium Speed button
Airflow speed is ideally for ventilation in standard cooking operation.

3 High Speed button
When high density of smoke or steam produced, press high-speed button for high effective ventilation.

Booster button
Depress this button to enter into highest speed and again to turn off motor.

Light
Short press for lamp control.

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.

I. Regular Cleaning
Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit.

II. Monthly Cleaning for Grease Filter
ESSENTIAL: Clean the filter every month can prevent any risk of fire. The filter collects grease, smoke and dust…… so the filter is directly affecting the efficiency of the cooker hood. If not cleaned, the grease residue (potential flammable) will saturate on the filter. Clean it with household cleaning detergent.

III. Annual Cleaning for Activated Carbon Filter
Apply SOLELY to unit that installed as a recirculation unit (not vented to the outside). This filter traps odors and must be replaced at least once a year depending on how frequent the cooker hood used.

IV. Changing a light bulb
Remove the screws on the glass, take off the hood glass. Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders and wiring from the hood. Important: It’s not possible to replace the bulbs individually, it will be necessary to obtain the bulbs, bulb holders and wiring as a complete part. (LED light: MAX 1.5W)

Fit the replacement bulbs, bulb holders and wiring in the same manners as the originals. Then reconnect the light wiring point.

Refit the hood glass and fasten the glass screws. Make sure the screws are fully tightened.

TROUBLESHOOTING

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the appliance and contact the Assistance Service.

PRODUCT SERIAL NUMBER. Where can I find it? It is important you to inform the Assistance Service of your product code and its serial number (a 16 character code which begins with the number 3); this can be found on the guarantee certificate or on the data plate located on the appliance. It will help to avoid wasted journeys to technicians, thereby (and most significantly) saving the corresponding callout charges.

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>