Energetic ENG rev2 Wet Dry Vacuum Cleaner User Manual

June 13, 2024
energetic

Energetic-logo

Energetic ENG rev2 Wet Dry Vacuum Cleaner

Energetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-product-
image

Product Information

  • Congratulations on your purchase of the new wet/dry vacuum cleaner. This appliance is designed to effectively clean both wet and dry surfaces. Before using the vacuum cleaner for the first time, it is important to read and understand the user manual for proper usage instructions.
  • The vacuum cleaner should not be operated in the presence of flammable materials or vapors, as it can cause a fire or explosion. It is also advised to never operate the vacuum cleaner unattended. Eye protection should always be worn to prevent injury from rocks or debris.
  • The appliance must be cleaned and serviced prior to use, as well as before replacing any components or changing over the appliance. If foam develops or liquid emerges, the appliance should not be used until the issue is resolved.
  • For users in the United Kingdom, it is essential to read the specific instructions provided, as the machine is fitted with a 240 volt 50 Hz power supply and a 13 amp. 3 pin moulded plug. The correct replacement fuse should be used, and the fuse cover should never be removed. Replacement fuse covers can be obtained from any electrical retail outlet.
  • Electrical tests must be performed in accordance with safety regulations EN 62638 at regular intervals and after any repairs or modifications. The vacuum cleaner has been approved in accordance with IEC/EN 60335-2-69.

Note: The drawings and pictures provided in the manual are indicative and serve as a guide.

Product Usage Instructions

Overview:

  1. Tank

  2. HFeIaGd

  3. Trolley (optional)

  4. Hose and cord storage hook (optional)

  5. Clamp

  6. Drain outlet

  7. Suction inlet

  8. Blow regulation

  9. Blow outlet

  10. Control panel

  11. Filter Cleaning Button (optional)

  12. Cord rewind button (optional)

  13. Plug seat

  14. Cord Plug

  15. Nozzle storage holders

  16. Trolley lock screw

  17. Tube storage holders

  18. Crevice Nozzle

  19. Upholstery nozzle (optional)

  20. Brush nozzle

  21. Floor nozzle (dry pickup)

  22. Squeegee insert (wet pickup)

  23. Dust bag

  24. Power tool adapter (optional)

  25. Hose with handtube

  26. Hoses

Some accessories may be packed inside the tank. If any parts are missing, please contact our Customer Service Department.

First Time Set Up Instructions:
Please refer to the user manual for detailed first-time setup instructions.

DEAR CUSTOMER

  • Congratulations on the purchase of your new wet/dry vacuum cleaner.
  • Prior to using the appliance for the first time, be sure to read this document through and keep it ready to read instructions of use.

PURPOSE AND INTENDED USE

  • This vacuum cleaner is designed, developed and andrigorously tested to function efficiently and safely when properly maintained and used in accordance with the following instructions.
  • This vacuum cleaner is to be used for commercial (hotels, schools, hospitals, factories, offices and rental business) and/or for household use. Accidents due to misuse can only be prevented by those using the machine.

CAUTION: READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
This machine is suitable for picking up dry, nonflammable dust and liquids. Any other use is considered as improper use. The manufacturer accepts no liability for any damage resulting from such use. The risk for such use is borne solely by the user. Proper use also includes proper operation, servicing and repairs as specified by the supplier.

  • ATTENTION: REVIEW IMPORTANT SAFETY INSTRUCTIONS BEFORE ATTEMPTING TO USE THIS VACUUM CLEANER. RETAIN FOR FUTURE REFERENCE
  • DANGER: Never operate this unit when flammable materials or vapors are present because electrical devices produce arcs or sparks that can cause a fire or explosion.
  • NEVER OPERATE UNATTENDED!
  • WARNING: Always wear eye protection to prevent rocks or debris from being blown or ricocheting into the eyes or face which can result in serious injury.

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS FOR USE:
The appliance must:

  • only be used by persons, who have been instructed in its correct usage and explicitly commissioned with the task of operating it
  • only be operated under supervision
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.
  • Children shall be supervised to make sure that they do not play with the appliance.
  • Do not use any unsafe work techniques.
  • Never use the vacuum cleaner without a filter.
  • Switch off the appliance and disconnect the mains plug in the following situations:
    • Prior to cleaning and servicing
    • Prior to replacing components
    • Prior to changing over the appliance
    • If foam develops or liquid emerges

Besides the operating instructions and the binding accident prevention regulations valid in the country of use, observe recognised regulations for safety and proper use.

IMPORTANT WARNINGS:

  • To reduce the risk of fire, electric shock, or injury, please read and follow all safety instructions and caution markings before use. This vacuum cleaner is designed to be safe when used for cleaning functions as specified. Should damage occur to electrical or mechanical parts, the cleaner and / or accessory should be repaired by a competent service station or the supplier before use in order to avoid further damage to the machine or physical injury to the user.
  • Do not leave the machine when it is plugged in. Unplug from the socket when not in use and before maintenance.
  • Do not use with damaged cord or plug. To unplug grasp the plug, not the cord. Do not handle plug or cleaner with wet hands. Turn off all controls before unplugging.
  • Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run cleaner over cord. Keep cord away from heated surfaces.
  • Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts.
  • Do not put any objects into openings or use with opening blocked. Keep openings free of dust, lint, hair, and anything else that could reduce the flow of air.
  • WARNING: This machine is not suitable for picking up hazardous dust.
  • Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
  • Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
  • Use extra care when cleaning on stairs.
  • Do not use unless filters are fitted.
  • If the cleaner is not working properly or has been dropped, damaged, left outdoors, or dropped into water, return it to a service center or supplier.
  • If foam or liquid escapes from the machine, switch off immediately.
  • The vacuum cleaner may not be used as a water pump. The vacuum cleaner is intended for vacuuming air and water mixtures.
  • Connect the vacuum cleaner to a properly earthed mains supply. The socket outlet and the extension cable must have an operative protective conductor.
  • Provide for good ventilation at the working place.
  • Do not use the vacuum cleaner as a ladder or step ladder. The vacuum cleaner can tip over and become damaged.
  • Never vacuum up the following materials: explosive or combustible gases, liquids and dust particles (reactive dust particles), reactive metal dust particles (such as aluminum, magnesium, zinc) in combination with highly alkaline or acidic detergents, undiluted and strong acids and alkalis or organic solvents such as petrol, paint thinners, acetone, heating oil and similar products.
  • Risk of fire. Do not vacuum up any burning or glowing objects.
  • Do not not pick up flammable or combustible liquids such as gasoline, liquids, reactive dust particles or use in areas where they may be present.
  • Do not use your vacuum cleaner as a sprayer of flammable liquids such as oil base paints, lacquers, household cleaners, etc.
  • Do not attempt to vacuum hot or warm ashes. Maximum temperature of ashes should not be warmer than 102 degrees Fahrenheit / 40 degrees Celsius.
  • Do not vacuum toxic carcinogenic, combustible or other hazardous materials such as asbestos, arsenic, barium, beryllium, lead, pesticides or other health endangering materials.
  • To avoid spontaneous combustion, empty tank after each use.
  • NOTE: A static shock may occur if the environment is too dry. This will not affect the use of the vacuum cleaner. To eliminate shock, add humidity to the air with a console or a humidifier.
  • STAY ALERT and use common sense. Do not use vacuum cleaner when you are under the influence of drugs, alcohol, medication, or if you are tired or distracted.
  • Do not leave cord lying on the floor once you have finished the cleaning job. It can become a tripping hazard.
  • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similary qualified persons in order to avoid hazard
  • Do not allow to be used as a toy. Close attention is necessary when used by or near children.
  • Keep packaging material away from children. There is a risk of suffocation!
  • Protect the unit from rain. Store indoors only.
  • CAUTION: The machine is for indoor use only.
  • Do not operate the vacuum cleaner in the rain.
  • Wear protection mask, when tank is emptied for fine dust of all kinds.
  • Unplug before connecting hose and any attachments.
  • Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing it.
  • Connect to a properly grounded outlet only. See Grounding Instructions.
  • WARNING: Operators shall be adequately instructuted on the use of these machines
  • CAUTION: Clean the water level limiting device regularly and examine it for signs of damage.
  • The floater has the function to stop the vacuuming when the tank is full of fluids or in case of overturning;carry out routine cleaning,checking that it has no damage and change it if necessary.

ONLY APPLICABLE IN UK

  • Please read these essential instructions.
  • These instructions have been prepared with safety and efficiency paramount. The machine operator must be trained by a suitably qualified instructor and must understand these instructions for use, and be made aware of any relevant regulations and legislation in force at the time of use.
  • This 240 volt 50 Hz. machine are fitted with a 13 amp. 3 pin moulded plug. The plug is fitted with a 13 amp. detachable fuse. The correct replacement for the fuse is identified by marking or colour coding. Only fuses that are ASTA approved to BS 1362 should be fitted. Never use the plug without the fuse cover fitted. Replacement fuse covers are available at any electrical retail outlet.

Tests and approvals
Electrical tests must be performed in accordance with the provisions of safety regulations EN 62638. These tests must be performed at regular intervals and after repairs or modifications. The vacuum cleaner has been approved in accordance with IEC/EN 60335-2-69.
Note: All the drawings and pictures are merely indicative and given only as a guide.

OVERVIEW

Energetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-01

  1. Tank
  2. Head
  3. Trolley (optional)
  4. Hose and cord storage hook (optional)
  5. Clamp
  6. Drain outlet
  7. Suction inlet
  8. Blow regulation
  9. Blow outlet
  10. Control panel
  11. Filter Cleaning Button (optional)
  12. Cord rewind button (optional)
  13. Plug seat
  14. Cord Plug
  15. Nozzle storage holders
  16. Trolley lock screw
  17. Tube storage holders
  18. Crevice Nozzle
  19. Upholstery nozzle (optional)
  20. Brush nozzle
  21. Floor nozzle (dry pickup)
  22. Squeegee insert (wet pickup)
  23. Dust bag
  24. Power tool adapter (optional)
  25. Hose with handtube
  26. HosesEnergetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-02

Some of these accessories are packed inside the tank. If parts are missing, contact our Customer Service Dep.

FIRST TIME SET UP INSTRUCTIONS

Read chapter 1 – IMPORTANT SAFETY INSTRUCTIONS of this manual thoroughly before setting up and using this vacuum cleaner.

ACCESSORIES
The nozzles and accessories for the machine is during shipping stored in tank. To open the tank open the clamps and take off the head. Take out the items and put on the head again. Secure the head with the clamps.Energetic-
ENG-rev2-Wet-Dry-Vacuum-Cleaner-03 See chapter 6 where to store the accessories on the machine.

MOUTING OF HOSE AND CORD HOLDER

Add the two hose/cord holders in the appropriate receptible on the head

PREPARING THE TROLLEY (OPTIONAL)Energetic-ENG-rev2-Wet-Dry-Vacuum-
Cleaner-05 The trolley can be folded during transportation. To fix it in the upright position swing the top trolley part up (A) and fix it with the 2 screws (B). Make sure to tighten both sides equal.

USING THE VACUUM CLEANER

Read chapter 1 – IMPORTANT SAFETY INSTRUCTIONS of this manual thoroughly before setting up and using this vacuum cleaner.

WORKING WITH DUST BAGS
If sucking up dry dust an optional dust bag can be used to collect the dust and ease the disposal. To insert the dust bag take off the head (see also figure 3). Insert the dustbag like shown on figure 6. Put on the head again and secure the head with the clamps.

DRY OR WET FLOOR SUCTIONEnergetic-ENG-rev2-Wet-Dry-Vacuum-
Cleaner-07

  • To suck up dry dust and debris use the dry floor nozzle (A) with the bristles rim.
  • To suck up wet debris replace the brush rim with a screwdriver and insert the rubber squeegees

VACUMING – INSERTING AND REMOVING THE HOSE

  • To vacuum insert the hose (A) into the suction inlet (B).
  • To remove the hose twist and pull in one movement to remove (C)Energetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-08

BLOWING – INSERTING AND REMOVING THE HOSE

  • The machine can also be used for blowing. In some cases it is easier first to blow the debris away and then afterwards collect it.
  • To use the blow function insert the hose into the blow outlet (A) in the same way for the suction inlet. See above. The blowing can be controlled by the lever (B)Energetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-09

TURNING THE MACHINE ON

  • The machine is turned on/off by pressing the start/ stop button (A).
  • The machine can optionally be equipped with LEDs with power control (C). By turning the knob the suction of the machine can be controlled. The suction performance is also shown by the LEDs. If equipped with LED the 1st LED from left, when the machine is plugged in, will be ON.
  • To use the optional socket (B) see next chapter.Energetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-10
  • The machine can optionally be configured with an indicator (D).
  • The indicator goes on, when the underpressure is high.
  • This can be due to the filter being clogged and needs to be cleaned (see later chapter) or the bag is full and need to be replaced.

MACHINE WITH SOCKET AND AUTO START/STOP (OPTIONAL)
The machine can optionally be equipped with a socket that can be used in connecting with a power tool. Connect the power tool to the socket (A). Remove the handtube and fix the conical adapter (B). Insert the conical adapter to the power tool (C). Turn the machine to AUTO mode with the switch (D). The machine will then start, when the power tool is turned on and stop with a delay (in order to empty the hose) when the power tool is turned off .Energetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-11

  • WARNING – Do not operate without filter basket and float, as they prevent liquid from entering the impeller and damaging the motor. Do not suck up any liquids without a sponge filter installed.
  • WARNING – To reduce the risk of back injury or falls, do not lift a vacuum cleaner heavy with liquid or debris. Scoop or drain enough contents out to make the vacuum cleaner light enough to lift in a comfortable manner.
  • NOTE: IF ACCIDENTALLY TIPPED OVER, THE VACUUM COULD LOSE SUCTION. IF THIS OCCURS, PLACE VAC IN UPRIGHT POSITION AND TURN SWITCH OFF. THIS WILL ALLOW THE FLOAT TO RETURN TO ITS NORMAL POSITION, AND YOU WILL BE ABLE TO CONTINUE OPERATION.
  • WARNING – Read the Safety Warnings and Instructions concerning the types of wet materials that cannot be vacuumed with this product.
  • DANGER – This equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an explosion. Do not pick up flammable, combustible, or hot materials. Do not use around explosive liquids or vapors, as electrical devices produce arcs or sparks which can cause a fire or explosion – do not use at filling stations or anywhere gasoline is stored or dispensed.
  • Note: This vacuum cleaner has a built in thermal overload protector to protect the motor from high temperatures. This can occur under heavy use. If the motor temperature shuts off during operation, turn the switch off and allow the motor to cool for 5 minutes. Turn switch on and resume operation.

EMPTYING THE TANK FOR LIQUID

  • To empty the tank for liquid unscrew the drain plug (A) and remove it. Energetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-13
  • Discharge water from filter.

EMPTYING THE TANK FOR DUST/DEBRIS

  • To empty the tank for dust/debris take off the head (see chapter 3.1). If using a dust bag remove the dust bag and insert a new.
  • Machines with 20l and 30l plastic tanks are equipped with a handle (A) that can be using during disposal of the dust/debris.

FILTER CLEANING

The machine can optionally be equipped with a semi automatic filter cleaning system or fully automatic filter cleaning system.

MANUAL FILTER CLEANING
When sucking fine dust the filter will eventually get clogged and suction will go down. The filter therefore needs to be cleaned to restore suction. If the machine is not equipped with semi- or fully automatic filter cleaning system (see next chapters), the filter can be cleaned in the following manual way. Turn the knob (A) and remove the knob from the filter disc (B). Remove the filter (C). Clean the filter under cold water (D). Let is dry (E) until completely dry. Install backwards by adding filter (F). Fixing the filter disc (G) and securing it with the knob (H). Energetic-ENG-rev2-Wet-Dry-Vacuum-
Cleaner-16

SEMI AUTOMATIC FILTER CLEANING (OPTIONAL)
When the machine is equipped with the semi automatic filter cleaning system, the filter can be cleaned by closing the inlet of the handtube (A). However, first turn the machine to max. power if equipped with power control (see figure 10). Close the inlet which can be done with your hand or the receptable/hole in the machine (B) can be used. After closing the inlet wait 2-3 seconds until the maximum underpressure has been built up. Press the filter cleaning button (C) 5 times fast after each other. This action will clean the filter and restore suction performance.

Energetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-17
FULLY AUTOMATIC FILTER CLEANING (OPTIONAL)
The fully automatic filter cleaning system cleans the filter automatically approx. every 20 seconds. The filter cleaning takes less than a second and a very little interruption of the suction performance takes place during the filter cleaning. A small “bang” can be heard. The automatic filter cleaning system works best, when the underpressure in the machine is high. If filter for some reason should be clogged and suction is low then turn the machine to max. power (if configured with power controller) then close the inlet of the machine and wait until a small “bang” can be heard. The filter will then be cleaned and suction restored.

DURING OR AFTER USE, STORAGE

  • Store vacuum cleaner INDOOR in a room above 0°C and store in a dry room.
  • The tubes can be stored either single (A) on the back of the machine e.g. when the machine is being moved from one place to the other or together (B) via the parking hook/function in between use.

Energetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-18

  • The nozzles can be stored in the accessory holders on the head
  • For machine without cord rewinder the cord (A) can be stored in the hooks. These hooks can also be used for storing the hose (B) by coiling it around the machinesEnergetic-ENG-rev2-Wet-Dry-Vacuum-Cleaner-20
  • When transporting from one place to another the tubes can be put on the handle as seen on figure

WARNING! When not in use: disconnect the power cord from the electrical outlet.

TROUBLE SHOOTING

Repair or service of electrical components such as cord or motor, must only be carried out by an authorized service center.

Vacuum does not start:-|

  • Check to see that the plug is correctly inserted in the electrical outlet and that there is power at receptacle.
  • A circuit breaker may have tripped. Check the circuit breaker box.
  • The cord or plug may be damaged. Call the Customer Service Department to get the nearest authorized service center.

---|---
Motor does not run in automatic mode|

  • Power tool defective or not connected properly. Check that the power tool works or that the plug is inserted correctly.
  • The power rating of the electrical tool is too low. Note that minimum power rating is P>50W

Motor stops:|  A thermal overload protector will shut off the motor if the motor temperature is too high. If this occurs, turn the switch off. Wait 10 minutes for the motor to cool. Turn switch on and resume operation.
Suction power is reduced:|

  • The tank may be full and needs to be emptied. See chapter 4.7 and 4.8.
  • The wands, hose and nozzle may be clogged and need to be cleaned.
  • Any of the above may be damaged and need to be replaced.
  • The filter may be clogged. Use the Filter Cleaning System (see chapter 5), to clean the filter
  • Check the filter and replace it, if it’s necessary. Make sure that is installed properly.
  • The hose connection is loose and need to be tightened.

Static shocks:|

  • If the environment is too dry, add moisture to air. If possible, use a humidifier
  • In case the relative humidity of air is low, please note that this situation will not have any effect on use of the vacuum cleaner.

DECLARATION OF CONFORMITY

  • 2006/42/EC – 2014/30/EU – 2011/65/EC
  • 2006/42/EC – 2014/30/EU – 2011/65/EC

We:

  • IP Cleaning S.r.l.
  • Viale Treviso, 63
  • 30026 Summaga – Portogruaro (VE) – Italy
  • declare under our responsibility that the product

NRG 1/20 CLEAN P

  • 220-240 V / 50-60 Hz
  • 1200 W nom / 1200 W max

| NRG 1/30 CLEAN TC SL PT P

  • 220-240 V / 50-60 Hz
  • 1400 W nom / 3600 W max

| NRG 1/30 CLEAN TC SL PT S

  • 220-240 V / 50-60 Hz
  • 1400 W nom / 3600 W max

---|---|---

to which this declaration relates is in conformity with the following standards or other normative document(s):

  • IEC 60335 -1:2010+A1:2013
  • IEC 60335 – 2 – 69:2012
  • EN 62233: 2008
  • EN 55014 – 1:2006+A1:2009+A2:2011
  • EN 55014 – 2:1997+A1:2001+A2:2008
  • EN 61000 – 3 – 2: 2014
  • EN 61000 – 3 – 3: 2013

following the provisions of the Directives: 2006/42/EC (Machinery directive) 2014/30/UE (Electromagnetic combability EMC) 2011/65/EC (Directive RoHS II)

  • Person authorised to compile the technical file IP Cleaning S.r.l.
  • Viale Treviso, 63
  • 30026 Summaga – Portogruaro (VE) – Italy

PRODUCT SPECIFICATIONS

Model name| NRG 1/20 CLEAN P| NRG 1/30 CLEAN TC SL PT P| NRG 1/30 CLEAN TC SL PT S
---|---|---|---
Voltage| 220-240V| 220-240V| 220-240V
Frequency| 50Hz/60Hz| 50Hz/60Hz| 50Hz/60Hz
Power| 1200 W| 1400 W| 1400 W
Connected load for appliance socket| –| 2200 W| 2200 W
Total Power| 1200 W| 3600 W| 3600 W
Protection Class| I| II| II
Type of protection| IPX4| IPX4| IPX4
Tank volume| 20L| 30L| 30L
Vibration| ah< 2.5 m/s2| ah< 2.5 m/s2| ah< 2.5 m/s2
Pressure level at a distance of 1

m, EN 60704-1

| 76 +/ -2 dB(A)| 76 +/ -2 dB(A)| 76 +/ -2 dB(A)
Power level| 86 +/ -2 dB(A)| 86 +/ -2 dB(A)| 86 +/ -2 dB(A)
| | Antistatic| Antistatic
| | |

IP Cleaning S.r.l.
Registered Office/Administration
Viale Treviso, 63 – 30026 Summaga – Portogruaro (VE) ITALY
Tel. +39 0421 205511
Fax +39 0421 204227

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

energetic User Manuals

Related Manuals