ENERGETIC LIGHTING E4WPA series Wall Pack Light Installation Guide

June 10, 2024
Energetic Lighting

Model # E4WPA series

Wall Pack Fixture
Installation Instructions

ATTACH YOUR RECEIPT HERE
Item Number………………..
Purchase Date………………..
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-492-6566.
www.energeticlighting.com

PACKAGE CONTENTS

Par Item Name Qty.
A Front lens cover housing 1
B Back fixture base 1
C Housing screw 2
D Conduit twist-out access port 3
E Wirenuts (pre-installed to wires) 3

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product. Failure to do so could lead to electric shock, fire or other injuries that could be hazardous or even fatal.

  • Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
  • Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  • This product must be installed in accordance with local, state and national electrical codes.
  • Installation work shall be completed by a licensed installer that is familiar with the
  • construction and operations of the product.

CAUTION:

  • This product can only be dimmed with standard 0-10v low voltage dimming systems.

NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired  operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

INSTALLATION INSTRUCTIONS

  1. Open fixture housing by removing two (2) screws located on hardware reference Release quick disconnect on wires between LED driver and front lens cover housing.

  2. Separate the front lens cover housing from back fixture base by lifting up at the connecting joints.

  3. Unscrew center twist out cover to allow building wires to pass through into housing.

  4. a Junction box mounting: Drill out the matching set of holes on the cast pattern that aligns properly with the screw positions on the existing building junction box (not provided)
    4b Direct mount to surface: Drill out the three (3) cast pattern hole locations as shown in the diagram above, use the back fixture base as a template and transfer hole locations to desired mounting position. Ensure appropriate mechanical support is provided by
    mounting surface material, use anchors if necessary (not provided).

  5. Use wirenuts to connect the appropriate input leads as shown in the following section. Connect optional low voltage DC dimming wires if desired, otherwise, leave insulated.

  6. Reassemble by reverse process in Step 2 and then Step 1 above to complete the installation and test with power to ensure a working fixture.

INSTALLATION INSTRUCTIONS WIRE GUARD

  1. Place Wire guard over housing, with a marker marks the locations of the 4 screw holes to have a location to drill.
  2. Drill holes at marked locations on the housing using a 3/32 in drill bit, with moderate torque, control the rotation speed <100/min to protect glass lens being hurt.
  3. Install wire guard to fixture with 4pcs M4x5 Self tapping screws (provided by the manufacture).

INSTALLATION INSTRUCTIONS SHADE PANEL

  1. Place shade on fixture and mark where to drill. 2 on both sides for screws
  2. Drill holes at marked locations on the housing using a 3/32 in drill bit, with moderate torque, control the rotation speed <100/min to protect glass lens being hurt.
  3. Install the shade to the fixture with 4 pc M3x6 self tapping screws (provided by the manufacture).

WIRING DIAGRAM

CARE AND MAINTENANCE

Clean with a mild, non-abrasive glass cleaner and soft cloth. Do NOT use solvents or cleaners containing abrasive agents. When cleaning the fixture, make sure the power is turned off, and any liquid spray should be applied to the cleaning cloth and not sprayed directly onto the fixture itself.

TROUBLESHOOTING

Problem Possible Solution Corrective Action
Fixture does not light. 1. Power is off.

2. Incorrect wire connection.
3. Defective wall switch.| 1. Check circuit breaker or wall switch.
2. Check wire splices.
3. Replace switch.
Circuit breaker trips when light is turned on.| Crossed wires or power wire is grounded out.| Verify wires are correctly connected.

WARRANTY

This fixture is warranted to perform free from defects for five years. If it fails to do so, you may return it with proof of purchase to 13445 12th St., Chino, CA 91710 for replacement.

Printed in China
www.energeticlighting.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Energetic Lighting User Manuals

Related Manuals