ENERGETIC LIGHTING E2DLS White 1050 Lumen Switchable White Round Dimmable LED Canless Recessed Downlight Instruction Manual

ENERGETIC LIGHTING E2DLS White 1050 Lumen Switchable White Round Dimmable

LED Canless Recessed Downlight

Product Specifications

• Model : E2DLS6-82765-L105
• Product Name : 6 IN LED RECESSED LIGHTING
• Dimensions: Diameter: 6 3/8 in.
• Color Temperature : Adjustable

Product Usage Instructions

Package Contents

• A – x 12
• B – x 12

Hardware Contents

• AA (M4*25mm) – x 24
• BB – x 36

Installation Overview

1. Locate a suitable location for the fixture and cut a 6 3/8 in round hole where the LED Ultra-Thin Downlight (A) will be installed.
2. Ensure this location has access to electrical wire from the switch (power supply).
3. Select the desired color temperature.
4. Carefully open the hardwire junction box (B) and remove the appropriate knockout(s).
5. Insert the electrical supply cable through the knockout and secure it with a cable connector (sold separately).
6. Using wire nuts (BB), connect the supply cable to the hardwire junction box (B): green to ground, white to white, black to black. Place all wiring connections back into the hardwire junction box (B) and close the cover.
7. Insert the hardwire junction box (B) through the mounting hole established in Step 1.
8. Connect the LED Ultra-Thin Downlight (A) to the hardwire junction box (B) by inserting and twisting the male/female connections of the attached connector cables together.
9. Push the spring-loaded clips on the LED Ultra-Thin Downlight (A) upwards and insert the base of the LED Ultra-Thin Downlight (A) into the mounting hole established in Step 1. Release the clips and the fixture will grip flush with the ceiling/drywall.

FAQ

• Fixture does not light. Le luminaire ne s’allume pas.
  • Possible Cause: Incorrect wiring connections.
  • Corrective Action: Double-check and ensure that green is connected to the ground, white to white, and black to black.
• Care and Maintenance
  • Please refer to the product warranty for information on care and maintenance.
• Warranty
  • Refer to the warranty document included with your product for specific details.

Installation Instructions

Thank you for purchasing this product. We’ve created these easy-to-follow instructions to ensure you spend your time enjoying the product instead of putting it together.

PACKAGE CONTENTS

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product

WARNING/AVERTISSEMENT

• Be sure the electricity to the wires you are working on is shut off.
  Risk of fire or electric shock. Do not alter, relocate, or remove wiring, lamp holders, power supply or any other electrical component. / Risque d’incendie ou

• Risk of fire or electric shock. LED retrofit kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact aqualified electrician. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire. / Risque d’incendie ou de choc électrique. L’installation de la trousse de modernisation à DEL nécessite une connaissance des installations électriques des luminaires. Si vous n’êtes pas qualifié, ne procédez pas à l’installation. Faites appel à un électricien qualifié. Installez cette trousse uniquement dans les luminaires ayant les mêmes caractéristiques et dimensions que celles qui paraissent dans les photos ou les illustrations. La puissance de la trousse de modernisation ne doit pas excéder celle du luminaire.

• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

• To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.

SAFETY INFORMATION

• CAUTION/ATTENTION
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation./Cet appareil est conforme à l’alinéa 15 du règlement de la FCC. Son utilisation est soumise aux deux conditions suivantes : (1) cet appareil ne doit provoquer aucune interférence nuisible; et (2) cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant entraîner un fonctionnement indésirable.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures

PREPARATION

Ensure the power is off before cleaning. Clean with a mild glass cleaner and soft cloth. Apply liquid cleaner to the cloth. Do not spray the fixture itself.

CAUSE POSSIBLE CORRECTIVE ACTION MESURE CORRECTIVE

The fixture does not light. Le luminaire ne s’allume pas.  Power is off incorrect wire connection, or defective wall switch.

Check the circuit breaker or wall switch, check wire splices, or replace wall switch. Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 10 minutes

TOOLS REQUIRED (NOT INCLUDED)

INSTALLATION OVERVIEW

TROUBLESHOOTING

CARE AND MAINTENANCE

Ensure the power is off before cleaning. Clean with a mild glass cleaner and a soft cloth. Apply liquid cleaner to the cloth. Do not spray the fixture itself.

WARRANTY

This fixture is warranted to be free from defects in materials and workmanship for 5 years from the date of the original purchase

CUT OUT TEMPLATE

Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>