SWIT FM-215HDR FM Field Monitors User Manual

SWIT FM-215HDR FM Field Monitors

4K input FHD Broadcast Monitor
Model: FM-215HDR

User Manual
Please read this user manual throughout before using
Ver : A

Declaration
Any internal technology (including hardware equipment, software design and product trademark) of the product shall be protected by law, and any infringement of intellectual property rights of the product shall be investigated for legal liability
All the brand and trademark in this product are protected by law, all other company’s brand and trademark in this product are protected by their owner’s law.
In order to better service majority users, SWIT products will keep improving and developing, SWIT keep the right to revise and improve this user manual without previous notice.
The warranty period of this product are two years, the following condition are not covered by the warranty:

1. The appearance and the LCD panel are damaged by man-made out force;
2. The amount of defective pixels are under three;
3. Damage the product by using incompatible power adaptor;
4. Damage the product due to violation operation;
5. Disassemble the product when using;
6. Other faults or damages not caused by design ,technology, manufacture and quality.

Any sales person have no right to provide extra warranty beyond these terms.

• If you have any advises or requirements about our products during using, please feel free to contact with us via phone or E-mail.
• This instruction manual applies to FM field monitors and the schematic is based on the exterior view of the FM-215HDR as an example. Any differences in specifications and appearance are explained in additional text in this manual.
• SWIT Electronics Co., Ltd.
• Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone,
• Nanjing 210038, P.R.China
• Phone: +86-25-85805753
• Fax: +86-25-85805296
• Email: contact@swit.cc
• http://www.swit.cc

Maintenance precautions

Warning

1. To reduce the dangerous of fire or electric shock , do not expose the monitor in raining or wet place.
2. The monitor will create noise when using near high-intensity magnetic field.

Precautions for power supply

1. Please use the special power adapter specified by the original factory to avoid damage to the product.
2. If other DC power supply is used, ensure that the voltage range, power supply and polarity of the power supply meet the requirements.
3. In the following cases, please unplug the power cord and external battery of the product:
4. If you have not used the product for A long period of time.
5. If the power cord or power plug/socket is damaged.
6. If the product is hit or dropped so that the shell is damaged.

Precautions for product use

1.  Please do not touch the screen surface directly with your fingers to avoid damage to the screen, and the oil on the skin will be difficult to remove if left on the screen.
2. Please do not put pressure on the LCD screen, LCD screen is very delicate and fragile.
3. Do not place the product in an unstable place, as the product may be seriously damaged due to falling.

Precautions for product cleaning

1. Clean LCD screen, please use dry soft fabric with fluff and special liquid crystal cleaning agent, to remove dust and stains on the screen.
2. Do not pressure when wiping the LCD screen surface.
3.  Please do not use water and other chemical cleaners to wipe the LCD screen surface, chemical agents may damage the LCD screen surface.

Packing list

Introduction

This series of monitor adopts full HD QLED screen, the resolution is up to 1920xl080, Hl 78°/Vl 78°ultra-wide viewing angle, 1000:1 contrast ratio, support 1 channel 12G/6G/3G/HD/SD-SDI input and output, 1 channel HDMI® 2.0 4K@60 input, and 3 channels 3G/HD /SD-SDI input and 1 channel 3G/HD/SD-SDI output, quad-link 4xSDI SQD /2SI 4Kp60/p50 inputs, 4-channel or 2-channel simul­taneous picture display with headphone and speaker outputs .

Features

• 21.5″ 1920Xl080 Full HD QLED screen.
• l000nits high brightness backlight HDR monitor.
• 97% DCI-P3 wide colour gamut ratio.
• 4K/UHD interface (lxl2G-SDI in/out, lx HDMI® 2.0 4K@60 input).
• 12GSDI, HDMI® Mixed Quad, Dual PBP and PIP Picture-in-Picture monitoring.
• 12GSDI, HDMI® dual-screen PBP vertical monitoring.
• Simultaneous display of HDR/SDR in multi-colour gamut for one signal.
• Read Payload ID to automatically set quantization, dynamic contrast, colour gamut, etc.
• 18bit high precision internal signal processing.
• Zero audio/video delay (0.01 frame).
• Built-in DelogSDR/HDR table for multiple cameras.
• 16-channel audio de-embedded sound column display, optional 2-channel output.
• Lissajous, 5.1 stereo phase map.
• Support waveform selection display/Cb/Cr/R/G/B /RGB and single line selection mode.
• Vector scope, R/G/B/Y histogram, bi-color focus assist.
• 3DLUT (17 x 17 x 17) accurate color correction, Fully automatic colour correction, no computer required.
• User 3DLUT uploaded via USB.
• UMD dynamic source name and soft TALLY display (TSL 3.1/4.0), GPI control interface.
• Composition ratio auxiliary line:4:3/13:9/14:9/15:9/16:9/l.85:l/2.35:l/2:l/2.39:l/Custom 1/Custom 2.
• Support USB firmware upgrade and import Log file.(USB file system supports FAT 32 format only).
• IP Webserver Web Control.
• Support ECO mode.

Operation Instructions

Front panel

1. Speaker: For SDI/ HDMI® embedded audio. (Will not work if earphone is plugged in)
2. Fl~FS function keys: Customize shortcut function keys. Users can set the shortcut keys to different functions according to their own requirements.
3. Userl~User4: Ul ~User shortcut key, which can be used to quickly enter the set user mode. Long press to save user settings. Please see details in “10. System”
4. Info/Quit: Display setting item. Press II Info/Quit II button to display or turn off relevant status information and audio and video analysis function graph. When opening the menu, press II Info/Quit II to exit the menu with one click

Press Brightness, Contrast, Saturation, Backlight, Volume five shortcut keys confirm to select this option, and rotate Menu to adjust the corresponding item value directly. Press the button and automatically cancel the selection without operation within five seconds, and the button light will be off, long press to restore default values; Adjust the volume.0~ 100 adjustable, the default value is 36.Long press the volume button to mute.

• Source: Select the input source signal format. 4xSDI

• SQD: Supports quad-link 4Kp60/p50 inputs 4xSDI
  2SI: Supports quad-link 4Kp60/p50 inputs

• Menu/Enter: When no Menu is displayed, press the button directly to open the Main Menu; Rotate the knob to select different settings or adjust parameter values, press the knob to set;

• LUT/Firmware : Update firmware or import LUT files, Auto Calibration;

• PHONE: 3.5mm headphone jack is used to monitor the embedded audio signals of SDI and HDMI®;

• Power: Power switch;

• Aluminium alloy flight case : to hold the monito.

Back Panel

1. Soil OUT: 12G/6G/3G/HD/SD-SDI 5D12 OUT:3G/HD/SD-SDI
2. Soil inn: 12G/6G/3G/HD/SD-SDI 5D12~4 IN: 3G/HD/SD-SDI
3. ETHERNET(Network interface): 1000M high-speed RJ45 Ethernet port, for web external control
4. HDMI® 2.0 4K@60 in :Will not display HDCP protected content
5. RS485:TSL UMD control port
6. GPI: GPI control port
7. Fan
8. VESA bracket mounting area
9. DC IN: 12V~ 17V
10. AC switch: turns AC power on or off
11. ACIN:100V~240V
12. Battery grommet mounting area

Flight Case

1. Flight case adapter plate: 3) can be used to secure other equipment (e.g., PTZ, wireless transmission equipment, etc.)
2. Flight case handle
3. Rubber cushion for luggage base

OSD

1. TALLY Light
   TALLY Light Controlled by GPI

2. Time Code(SDI)
   Under SDI input, the monitor can display Time code information (LTC, VITC1&2). If no Time code info is detected, it will display “TC UNLOCKED”. User can set function keys Fl ‘”‘-‘FS or GPI pins as “Time Code” to turn on or off this function.

3. On screen TALLY
   Control of the display signal via GPI

4. Source ID/UMD
   Display /UMD (TSL3.l/4.0), user can set in the UMD menu

5. Colour gamut char
   Used to monitor the colour fullness and fineness of the image, open the gamut chart to display the current video gamut, users can set the “Main Menu” – “Colour Management” –
   “Gamut”. Current colour gamut.

6. Histogram
   The horizontal axis of the histogram indicates the brightness of the image, from left to right indicates the increase of brightness, the left side represents the darker area, the right side is the brighter area, the vertical axis of the histogram indicates the distribution of the number of pixels, the higher the vertical coordinate, the higher the brightness density.
   The vertical axis of the histogram represents the distribution of the number of pixels, the higher the vertical coordinate, the higher the luminance density, users can set the front panel shortcut keys (Fl ~FS) or GPI pins to the “Histogram” function, to turn on/off this function.

7. Waveform
   Used to display multiple signals sampled at the same rate, users can set the front panel short­cut keys (Fl ~FS) or GPI pins to the ” Waveform ” function to turn on or off the Waveform graph and select different types of Waveform graphs; the parameters of the Waveform graph, such as the position, transparency, color, etc. are set in the ” Waveform Setting” submenu. Wave­form parameters, such as position, transparency, color, etc., can be set in the ” Waveform Setting” submenu.

8. Vectors
   Used to monitor the colour, shape, outline, size and position of the image, etc. Users can set the front panel shortcut keys (Fl to FS) or GPI pins to the “Vector Graphics” function to turn on/off this function, and the display position, colour, transparency and other related parame­ters of the vector graphics are set in the “Vector Graphics Settings” submenu.

9. Lissajous
   Used to monitor the audio frequency analysis and phase amplitude difference determination, the user can set the front panel shortcut keys (Fl ~FS) to “Li Sha Yu” function, open/close this function.

10. Audio Meter
    Used for monitoring audio information, users can set the front panel shortcut keys (Fl ~FS) or GPI pins as the function of “Audio Meter” to turn on/off this function, the display position of the audio meter, the number of displayed channels, transparency and other related parame­ters are set in the Audio Settings sub-menu.

11. Surround Phase
    Monitor the sound source location of the full-space stereo sense of knowledge, Surround Phase default 5.1, the default 7, 8 channels, the user can be in the menu “data de-embedding” – “left / right channel”, set the desired sound channels

12. Eye pattern
    Used to monitor the strength of the SDI signal quality, the larger the eye chart image, the stronger the signal quality.

13. Colour checklist
    After auto calibration, the gamut value and colour difference (6E) before and after calibration 11
    will be popped up. “Auto calibration11- Measurement11 pops up the gamut value and colour difference (6E) of the last calibration and the current measurement.

Button operation

1. Press the “Menu/Enter” knob, the menu pops up in the upper left corner of the screen, and the currently selected menu is highlighted in yellow.

2. Rotate the “Menu/Enter” knob to select all kinds of sub-menu, the corresponding item is high­lighted in yellow, press the “Menu/Enter” key, the sub-menu is selected and enter the parameter setting sub-menu.

3. Rotate the “Menu/Enter” knob to select the item to be adjusted, press the “Menu/Enter” knob, the adjustment items and parameters are highlighted in yellow.

4. rotate the “Menu/Enter” knob to adjust the parameters, complete the settings, click
   “Menu/Enter” to save the settings.

5. Rotate “Menu/Enter” to select “Exit”, click “Menu/Enter” knob to exit the sub-menu, select “Exit & Status” in the main menu. Select “Exit & Status” in the main menu, click the “Menu/Enter” knob to exit the main menu.

Note

1. Items displayed in grey cannot be set;
2. If there is no operation within the set time, the menu will automatically save the settings and exit.
3. If the key lock function has been turned on, all items except “System Setting” will be displayed in grey, if you want to adjust any item, please set the key lock function to “Off” first.

Menu Configuration

•  Menu configuration introduces the main menu and the sub-menu, marked* menu items will be given in the list after a more detailed description of the menu or the operation of the explanation
• Exit & Status – Exit the main menu and display the current status of the monitor.

Press “Menu/Enter” key, the main menu pops up in the upper left corner of the screen, and the main menu shows the current working status of the monitor.

1. Standard
   Display the standard of the current input signal; if there is no recognizable signal input, “No Signal” will be displayed. If you select Multi-screen for the current channel, and select 4- screen, 2-screen or Picture-in-Picture for the Multi-screen type, the standard will display the input signal standard of the screen 1/2/3/4 or screen 1/2 channel respectively.

2. Input source
   Displays the currently selected channel.

3. Colour Temperature
   Displays the currently set colour temperature mode

4. Function key !~Function key 5
   Displays the currently set function value of the function key

5. Model
   Displays the current monitor model

6. Version
   Displays the current software version number

Input-Set the color of input video

• Full 0-1023,
• SDI Full 4-1019,
• Limited 64-940

Red Gain| Adjust Red Gain| -100 ~ +100
Green Gain| Adjust Green Gain| -100 ~ +100
Blue Gain| Adjust Blue Gain| -100 ~ +100
Red Bias| Adjust Red Bias| -100 ~ +100
Green Bias| Adjust Green Bias| -100 ~ +100
Blue Bias| Adjust Blue Bias| -100 ~ +100
Reset| Reset the gain and bias values of the settings| I

Input Range: Sets the quantization range of the video to suit the input video signal. The default video quantization range is Limited 64-940 for the broadcast application

 Image setting·1-Setting for the picture preference

• Image Settings
  • The image settings for contrast, brightness, saturation and backlight can be quickly adjust­ed using the front panel shortcut keys.

Color management-Setting about video colors

OFF,J-Logl,Log-C,S-Log2,C-Log,V-Log,RedLogFilm, S-Log3,User-Log
D-Logto PQ| Camera table when gamut is set to Rec.2020 and gamma value is PQl000| OFF, ARRI_LogC_PQ,Canon_CLog2Cin_PQ Canon_CLog3Cin_PQ,Panasonic_VLog_PQ, RED_L3GlO_PQ,Sony_SLog3_Cin_PQ, Sony_SLog3_SG3_PQ
| D-Logto HLG| Camera table when gamut is set to Rec.2020 and gamma value is HLGlO00| OFF,ARRI_LogC_HLG,Canon_CLog2Cin_HLG Canon_CLog3Cin_HLG,Panasonic_VLog_HLG, RED_L3GlO_HLG,Sony_SLog3_Cin_HLG,
| | | Sony_SLog3_SG3_HLG
Partition HDR/SDR•4| Partition HDR/SDR on, off| OFF,ON
Color temp| Set screen display colour temperature values| D55,D65,D75,D93,DCl,USER1,USER2

User temp

| Set the user color temperature value when the color temperature mode is selected as “USER l/USER2”| ****

4000K~9800K

**** G/M| Set the user color temperature value when the color temperature mode is selected as “USER l/USER2”| -100 ~ +100
LUT Upload·s| Select the cube file you want to import| None, 3DLut.cube, User- Log.cube
Calibration LUT Reset| Select the appropriate cube file to

restore to factory settings

| NO, 3DLut.cube

1. Color gamut
   Set the gamut to match the input audio.

2. Gamma
   When Four-screen is selected; the gamma of four signals can be adjusted separately for display *3 HLG System Gamma
   Display tunable only when Gamma is set to HLGl000

3. Partition HDR/SDR
   Individual colour gamut for Partition HDR/SDR, gamma can be adjusted individually, Partition HDR/SDR default colour gamut Rec.2020, gamma 2.2.

4. S LUT Upload
   Place the cube file that needs to import the monitor in the root directory of the u-disk, insert the u-disk into the USB interface on the front shell of the monitor, and choose to import the corre­sponding file

Scanning-Setting for picture scan, zoom, etc.

To Pixel, Panel Fit, Native
Zoom-in·2| **** Set a zoom mode| OFF, Top Left, Top, Top Right, Left, Center, Right, Bottom Left, Bottom ,Bottom Right
Freeze Frame| Select an image still mode| OFF, ON
Odd/Even Frame·3| Set to open odd field or even field| OFF, Odd Frame, Even Frame

• Scanning
  • Panel Fit: Turn on this feature to adapt the video to the entire screen. Pixel To Pixel only displays the original mode in the specified mode.
• Zoom -in: Shown below, the image is divided into 9 regions and adjusted to display in sequence.

When the zoom mode is turned on, a rectangle box pops up at the bottom left of the screen, showing the currently selected zoom image area.

• 0dd/Even Frame
  Odd/Even Frame is only displayed in I mode. Open Low Latency Mode and Odd/Even Frame function is turned off.

Control-Setting for TALLY, UMD, IP control to the monitor

SDl4, 4XSDI 2-Sk 4XSDI SQD, HDMI®, Red Tally, Green Tally, Yellow Tally ,Time Code, Freeze Frame, WFM Type, WFM Single Line, UMD, Marker, Waveform, Audio Bar, Zebra, Vector, Low Latency Mode, Histogram, Focus Assist, False Color
GPI 2Pin
GPI 3Pin
GPI 4Pin
GPI SPin
GPI 6Pin
Tally Setting| Switch on/off Tally light| OFF, ON, Blinking
Tally Position| Set the display position of On Screen Tally Lamp| Top, Bottom
Fl| Set the control function of the function key| Time Code, Color Temp, Freeze Frame, Waveform, Waveform Type, UMD, Marker, H/V Delay, Blue Only, Audio Bar, Zebra, Vector, Low Latency mode, Histogram, Odd/Even Frame, Focus Assist ,False Color, CIE
F2
F3
F4
FS
UMD2| Open or close UMD display| OFF,ON
UMD Color| Set the color of UMD characters| White, Red, Green, Blue, Black, Gray
UMD Position| Set the position of UMD characters| Top ,Bottom
UMD Size| Set the size of UMD characters| Large, Small
UMD Blending| Show the transparency of the UMD background| OFF, LOW, HIGH
Display Type| Set display UMD or source name characters| Source ID, TSL3.l,TSL4.0
RS485 Address3| Set the location of RS485| 1~126
Baud Rate| Fixed for 115200| 115200,8,n,l/ 38400,8,n,l/ 9600,8,n,l
Source ID| Set the character that the source name displays| A-Z, a-z, 0-9, [\)A_'{!}~@?>=<,,/.-+* ()’ &%$#” !

GPI control

• Connect the GPI remote control terminal through the GPI interface on the real panel of the monitor, turn on “GPI control” and set the function of GPI 1-6 buttons.
• The GPI control allows you to control both the Tally light and the on screen TALLY light on at the same time:

UMD
Select the display type as “”TSL3.lor 4.0”, which can be controlled with TSL UMD.

Cascade:

3 RS485 address
When Multi-screen-“4-screen or 2-screen” is selected, if screen 1/2/3/4 or screen 1/2 are set to different addresses, the UMD of a single screen can be controlled separately

 Assist-Setting for Vector scope and Histogram patterns.

Waveform

| Waveform| Turn waveform on or off| OFF,ON
WFMType| Set the WFM Type| Y, Cb, Cr, R,G,B,RGB
WFM Position| Set the WFM position| Bottom Left, Bottom

Right, Top Left, Top Right

WFM Blending| Set the blending of the background color of the waveform| ****

OFF, High, Low

WFM Brigh| Set the brightness within a WFM image| Low, Medium, High
WFM Color| Set the color of the waveform displayed on the

waveform chart

| White, Green, Color
WFM Single Line·1| Switch on single line waveform| OFF,ON
WFM Line Count| Set a line for the single line waveform| 1-1080

Vector

| Vector| Turn vector on or off| OFF, ON
Vector Position| Adjust the position of the vector on the screen| Bottom Left, Bottom Right, Top Left, Top Right
Vector Blending| Vector scope transparency selection| OFF, LOW, HIGH
Vector Brigh| Set the brightness within a vector image| Low, Medium, High
Vector Color| Set vector colors| White, Green, Color
CIE| CIE| Turn the colour gamut chart on or off| On,Off
CIE Position| Adjusting the position of the colour gamut map on the screen| Top left, Top right, Bottom left, Bottom right
CIE Blending| Set the transparency of the background colour of the colour gamut map| Off, Low, High
CIE Bright| Set the brightness within the colour gamut map chart| Low, Medium, High
CIE Color| Set gamut map colours| White, green, colour
Histogram| Histogram| Turn histogram on or off| OFF, ON
Histogram Position| Set the display position on the histogram screen| Top left, Top right, Bottom

left, Bottom right

Histogram Blending| Set the transparency of histogram background color| OFF, LOW, HIGH

Marker

| Marker| Turn marker on or off| OFF, ON
Marker Select| Set the scale of the market line| 16:9,15:9,14:9,13:9,4:3,2.35:1,2:1,

1.85:1,2.39: 1, USERl, USER2

Horizontal(user 1)’2| Set the X – axis value of the marker| 50%~99%
Vertical(user 1)| Set the Y – axis value of the marker| 50%~99%
Horizontal(user 2r3| Set the X – axis value of the marker| 0~1920
Vertical(user 2)| Set the Y – axis value of the marker| 0~1080
| Safety area| Set safety area percentage| 80%~100%
Fit Marker| Set safety area to fit marker ratio or not| OFF, ON
Center Marker| Switch on the center cross marker| OFF, ON
Marker Color| Select a color for marker| White, Red, Green, Blue, Black, Gray
Marker type| Set the display type of marker| Type 1, Type 2
Marker outside| Marker outside color setting| OFF, Black, Gray
Eye pattern· 4| Turn eye pattern on or off| ON,OFF

• WFM Single Line

  • Open waveform single-line mode, the monitor shows only one line of audio waveform. Rotate the Menu/Enter knob to select the number of lines of audio signal to display the waveform.
    (The selection range of the number of lines in a waveform depends on the current signal standard)

• Horizontal / Vertical (user 1 )

  • When the value of the scale item is set to “User l”, the user can adjust the X position and Y position of the marking line according to his/her own needs, and the coordinate value can be adjusted in the range of 50%~99%;

• Horizontal / Vertical (User 2 )

  • When the value of the scale item is set to “User 2”, users can adjust the X position and Y position of the marking line according to their own needs, and the X coordinate value can be adjusted in the range of 0~ 1920, and the Y coordinate value can be adjusted in the range of 0~ 1080.

• Eye pattern

• Only SOil supports eye diagram to monitor the image quality of the current SDI video signal after transmission over the cable, especially the transmission quality of 12G SDI.

De-embed- Setting for video/audio analysis functions

meter on the screen

| Top Left, Top Right, Bottom Left, Bottom Right
Audio meter Blending| Set the transparency of the audio meter background colour| OFF,LOW,HIGH
Audio meter marke·r 1| Setting the audio meter marker line| ON,OFF
Lissajous| Lissajous Pattern| Turn on or off Lissajous figure| ON,OFF
Lissajous position| Set the position of the Lissajous

position on the screen

| Top Left, Top Right, Bottom Left,

Bottom Right

lissajour Blending| Set the Blending of the Lissajous

background colour

| Off, Low, High

Surround

Phase

| Surround Phase| Turn surround Phase on or off| ON,OFF
Surround Position| Adjusting the position of the surround

sound display on the screen

| Top Left, Top Right, Bottom Left, Bottom Right
Surround type| Selecting the type of surround sound| 5.1,
Surround Blending| Set the transparency of the surround

sound background colour

| OFF,LOW,HIGH
Left Channel’2| Select the left channel output channel| Channel 1~16
Right Channel| Select the right channel output channel| Channel 1~16
Volume| Adjust audio volume| 0~100
Time code| Turn on/off Time code| OFF,ON
H/V Delay’3| Turn on/off H/V Delay| OFF,ON

1.  Audio meter marker
   • Audio table display, display 16 channel audio table
   • Marking line off: Only the audio table is displayed
   • Marking line on: Display audio decibels, audio alarm signal and left and right channel options
2. Left Channel/ Right Channel
   • Audio meter under SDI showing 16 channel audio meter
   • Audio meter under HDMI®, menu shows 8 groups of channels
3. H/V Delay
   • H/V Delay is not displayed on HDMI® channel.

Auto Calibration

Auto Calibration

• The monitor has built-in 3DLUT colour calibration software, which supports Atheros X-rite 11 Pro OEM and JETI Specobosl211 colour probes directly connected to the monitor via USB.
• When calibration starts, the colour probe will read the standard colour graphics generated by the monitor and load the results to the monitor via the USB port.
• The monitor internally compares the standard colours with the colours read by the probe to generate a 3DLUT table and complete the automatic colour calibration.
• Calibration time: X-rite 11: 15 minutes, JETI Specobosl211: 45 minutes.
• Calibration result Delta E <1.0.

Probe Select
This monitor supports the following probes models:

Start Calibration
Steps:

1. Put the monitor into a dark room. Switch on the monitor.
2. 2. Connect the calibration instrument (compatible with x-rite and JETI color measuring instruments) and monitor via USB. Before calibration, ensure that the monitor and the color calibration instrument are in good condition and the monitor aging time reaches 30 minutes
3.  Enter the “Probe Select” and select the currently used calibration probe.
4. Enter the “Start Calibration” and select “yes” to start calibration. The monitor will display the prompt message and the color position prompt box. Put the sensitive part of the device in the color position prompt box correctly. Note that when placing the calibration instrument; do not squeeze the monitor’s LCD screen.
5. Select “yes” to begin auto calibration. The color calibration instrument will automatically measure the color of the screen and correct the color of the screen. During this process, it is necessary to observe the color calibration progress bar in the color correction prompt box.
6. Press “INFO” to terminate the color correction process at any time. When the prompt color calibration progress reaches 100%, the whole automatic color calibration is completed. After automatic color correction, press the “INFO” button to exit the menu and let the monitor enter the normal display mode.
7. After the automatic color correction, the display screen pops up “Before Calibra­tion” and “After Calibration”.

Measure
The monitor has been calibrated in factory. And may need to be re- calibrated after a period of time. Before re-calibrated, the measure function can check the current color to compare with the last time calibrated color, to decide if the monitor needs to be re-calibrated. Connect with the sensor probe and place the sensor probe onto the right position like calibration step. Enter “Auto Calibra­tion” – “Measure”. The monitor will generate several colors and finish measure within 30 sec­onds. And display the result as:

System-User profile saving, firmware update.

Factory,USER1,USER2,USER3,USER4
Save Profile| Save the current state as a user setting| USER1,USER2,USER3,USER4
Payload ID| When turned on, Payload ID information conforming to SMPTE ST 352 standard is automatically adapted| ****

OFF, ON

Low Latency Mode| Open or close low latency mode| OFF, ON
Green mode| Set the display mode of green mode| Black Backlight, Gray Backlight

Idle Duration

| Set how long it will be in the no-signal state and turn on green mode| ****

30 Sec, 1 Hour, 2 Hours, 4 Hours, OFF

1p·3| ****

Set up the monitor IP address to achieve remote web control

| 192.168.001.200
Net Mask| 255.255.255.000
Gateway| 192.168.001.001
Port(1024~65535}| 08080
OSD TIME| Set OSD display time| 5~180
Key Brightness| Set the brightness of the key lamp| OFF, Low, High
Language| Select Chinese or English language to display| Chinese, English
System Reset| Reset all Settings in the menu system| No/Yes
Update·4| Set whether to upgrade firmware| No/Yes

Keylock

The “Menu/Enter” button can be operated when the button is locked. “Key Locked” will be displayed on the screen when you press the Locked button or knob.

Recall Profile/ Save Profile

• User Settings provide 4 menu Settings, that is, users can save the current monitor menu Settings as one user Settings (USER ~USER4) according to usage habits. Then, when switching menu Settings, just select the corresponding “USER ~USER4” through the “Recall Profile” item to display the corresponding menu Settings. Example: By adjusting the parameters of the color temperature of 2200K, open the necessary auxiliary functions (such as: histogram), set the function key to the desired menu (such as Fl is set to “Blue Only”), and so on, the monitor Menu Settings can be “USER Settings” save as “USER” 1, rotating the “Menu/Enter” choose to load the USER Settings “set to the current” USER 1 “mode, the monitor Menu item value will show” USER 1 “mode to save Menu.

IP control

• Connect the monitor to the LAN through an ETHERNET interface, and the Monitor can be controlled by web page.

Enter Menu- System – IP/Net Mask/Gateway/Port to set the monitor address. Set the computer Ethernet IP addresses at the same LAN environment as the Monitor. Launch any of a web browser on the computer, and enter URL: Monitor IP+ Port (Example: 192.168.1.99.8080). The web server control page will be displayed.

• Used crossed wired cable for computer-monitor directly connection.
• Use straight-through wired cable for Router connections.
• Please seek help from your web master for any network connections.

Webserver page control interface

Update
System software can update by USB interface, and steps are as follows:

1.  Download the latest software package into the U-disk root direction.
2. Open the monitor and plug U-disk into USB into port.
3. Follow the step “Menu-System-Update”, the monitor will update automatically.
4.  When update finishes, press “Power” button, close and reboot the monitor.

Remark

1. Only copy one model and software version into the U-disk root direction.
2. Never shutdown the power during the update progress.

Multiview setting·1

PICl

| ****

Select channel 1 when set to PBP or PIP.

| SDI LSDI 2,SDI 3,SDI 4, HDMI®
PIC2| ****

Select channel 2 when set to PBP or PIP

| SDI l,SDI 2,SDI 3,SDI 4,HDMI®
PIPWindoe position| Select PIC2 position when set to PIP| Bottom Left, Bottom Right, Top Left,Top Right, Centre
Border| Switch on/off the border| On/OFF
Flip(PBP) *3| Type mode selected at the PBP| ****

Off, type 1, type 2, type 3

1. Multiview setting
   • Source selects Multi-screen before the Multi-screen Setup menu is adjustable and some menu functions are disabled;
   • When Multi-screen is selected, the quantization range, colour gamut and gamma of each chan­nel can be adjusted individually.
2.  Multiview type
   • 4- channel or2-channel independent 12G/6G/3G/HD-SDI or HDMI® mixed 4-screen or2-screen monitoring;
3. screen: If there is no signal input on the 4th screen, HDMI® signal appears on the 4th; *3 Flip(PBP)
   • Select the required type, and the screen is in vertical mode to monitor the screen.

Appearance and Size

Flight Case Monitor Appearance

Aluminium flight case (unit: mm)

Specification

Input/Output Interface

Input

| BNCX4| 12G/6G/3G/HD/SD-SDI X 1, 3G/HD/SD-SDI X3
HDMl ® Xl| HDMl®2.0 input
RS- 485Xl| TSL3.1/4.0 UMD dynamic source name input
RS- 485Xl| GPI (Tally) input
USBXl|
RJ-45Xl| Gigabit Ethernet port, IP web control access

Output

| BNCX2| 12G/6G/3G/HD/SD-SDI X 1, 3G/HD/SD-SDI X 1
RS-485Xl| TSL3.1/4.0 UMD dynamic source name output
Analog audio| Analog audio 3.5mm and speaker output
Other specifications
Operating Voltage AC| 100V~240V 50/60Hz
DC/Battery| 11V”-’17V
Power consumption| 60W
Operating Temperature| 0°C”-‘+45°C
Operating humidity| 10%”-‘90%
Storage ternperature| -15°C”-‘ + 60°C
Storage humidity| 10°/o”-‘90%
flight box size| 570X260X405mm
Net weight (main unit only)| 7.28KG
Net weight of flight box| 6.8KG

Supported standards: Signals of the following standards can be displayed on the monitor

3G supports level A/levelB; Support RGB444

• : The format is supported
• -: The format is not supported

Common Problems and Solutions

No display

| ****

The power is not turned on

| Please check if the power is connected, and then press “POWER” button to turn on the monitor

Unstable power voltage

| Reconnect to power supply
BNC or HDMI® cable loose contact or not correctly connected| ****

Check and correctly connect the BNC or HDMI® cable

The attached battery is no power| ****

Change battery

Using DIV power supply but the polarity is reversed| Refer to the provided power supply, reconnect the power.

Image or

color abnormal

| Bad contact of BNC or HDMI® cable| ****

Change the Video cable

Video signal has Interference

| ****

Remove the interference source(s)

Improper adjustment of the color parameters| Adjust the “Recall profile” to “Default” under “System” submenu

Distortion of the image

| ****

Reset the Aspect ratio

Set to Blue only| ****

Turn off the “pure color” setting

Turn on the “Focus Assist” function| Turn off the “Focus Assist” function
Turn on the “False Color” function| Turn off the “False Color” function

No audio output

| ****

Set mute state

| Cancel mute state or spin” MENU/ENTER” to adjust volume

Bad contact of signal cable

| ****

Change signal cable

Wrong connection or bad contact of Audio cable| ****

Connect to the correct input socket

• SWIT Electronics Co., Ltd.
• Add: 10 Hengtong Road, Xin’gang, Nanjing Economic and Technological Development Zone, Nanjing 210038, P.R.China
• Tel: +86-25-85805753 Email: contact@swit.cc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>