u-Box BXG.8914-S Bronco Fender Liners Inner Fender Wheel Well Instruction Manual

u-Box BXG.8914-S Bronco Fender Liners Inner Fender Wheel Well

Product Specifications:

• Part Number: BXG.8914-S
• Contents:
  • 1 x Button Head Socket Cap Bolts Screws M8*16
  • 36 x Button Head Socket Cap Bolts Screws M6*10
  • 6 x Button Head Socket Cap Bolts Screws M6*20
  • 5 x Button Head Socket Cap Bolts Screws M6*25
  • 11 x Flat Washer 1
  • 1 x Flat Washer 36
  • 1 x Flange Hex Lock Nuts M6161.5
  • 1 x Flange Hex Lock Nuts M8161.5
• Tools Required:
  • 2.5mm & 4mm Hex Bit Socket
  • 7mm Deep Socket
  • Drive Socket Ratchet Wrench
  • Phillips Screwdriver
  • 7mm Wrench

Product Usage Instructions

1. Installation Time: About 2 hours, 1-2 people may be needed. Installation time may differ according to your mechanical skill level.
2. Installation Instruction:
3. Step 1: Fully remove the front fenders by turning the clips on the underside of the fender down until they feel loose. Pull the fender away from the vehicle directly towards you, releasing the clips.
4. Step 2: Use a Phillips head screwdriver and panel clip removal tool to remove the clips along the lip of the fender and the section closest to the engine bay.
5. Step 3: Remove the fender by pulling down on it near the lip of the fender, and then out.
6. Step 4: Assemble the passenger side Rear Inner Fender Liners with the specified bolts and nuts as shown in the picture.
7. Step 5: Identify the installation holes circled in red on the vehicle for preparation.
8. Step 6: Install mounting brackets and screws as per instructions using Button Head Socket Cap Bolts Screws and Flat Washers.
9. Step 7: Lift and align the front inner fender liners with mounting holes, then install screws accordingly.
10. Step 8: Follow similar installation steps for the driver side using specific mounting brackets and screws as instructed.
11. Step 9: Complete installation and enjoy your off-road experience with the product.

Frequently Asked Questions

Q: How long does it take to install the front inner fender liners?

A: The installation typically takes about 2 hours, but may vary based on individual mechanical skill level and experience. Having 1-2 people assist can also help speed up the process.

Q: Are all necessary parts included in the BXG.8914-S package?

A: Yes, please verify that all parts listed in the contents section of the manual are present before starting the installation to ensure a smooth process.

Q: Can I view the electronic version of the installation instructions?

A: Yes, you can scan the provided QR code to access the electronic version (BXG.8914-S) for detailed visual instructions.

Front Inner Fender Liners BXG.8914-S

Contents

Tools required

• a. 2.5mm & 4mm Hex Bit Socket;
• b. 7mm Deep Socket;
• c. Drive Socket Ratchet Wrench;
• d. Phillips Screwdriver;
• e. 7mm Wrench;

Installation time

About 2 hours, 1-2 people may be needed. Installation time may differ according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)

To view the electronic version (BXG.8914-S), please scan the QR code.

Installation instruction

• Step 1: You will need to fully remove the front fenders by turning the clips on the underside of the fender down until they feel loose. Once loose, pull the fender away from the Bronco directly towards you, releasing the clips.
  Note: Both front and rear fenders are mounted in this manner.

• Step 2: Use a Phillips head screwdriver and panel clip removal tool to remove the clips along the lip of the fender and the section closest to the engine bay.
  Note: Check along the inner fender where it meets wheel well thoroughly. They are easy to miss.

• Step 3: Remove the fender by pulling down on it near the lip of the fender, and then out.

Passenger Side Installation:
Step 4: Assembly the passenger side Rear Inner Fender Liners (A2, B2, C2, D2, E2) with the Button Head Socket Cap Bolts Screws (M6*10), Flange Hex Lock Nuts (M6). As the picture shown.

• Step 5: According to the schematic diagram of the original vehicle shown in the figure below, identify the three installation holes circled in red to prepare for the installation of our product.

• Step 6: Next, install the mounting bracket (1) & (2). Use a rectangular mounting bracket for the hole in the middle position, and use oval-shaped mounting brackets for the holes on the sides. Use the Button Head Socket Cap Bolts Screws (M620), Flat Washer (M616*1.5) for all the installations. Do not tighten all the screws.

• Step 7: In this step, install our front inner fender liners. You will need assistance from another person to lift the liner and align it with the mounting holes of the central bracket. Then, proceed to install the mounting holes on the sides. Use the Button Head Socket Cap Bolts Screws (M625), Flat Washer (M616*1.5) to install all three holes. The hole above the mounting holes is intended for tightening the bracket after the installation screws are in place.

• Step 8: Tighten all the screws. Use the same installation step 1-5 & step 7 to install on the driver side. When you installing the driver side in the step 6, you need use the mounting bracket (3) to instead it in the picture. Use the Button Head Socket Cap Bolts Screws (M816), Flat Washer (M816*1.5), Flange Lock Hex Nuts (M8).

• Step 9:
  The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!

Attention

1. The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
2. Please feel free to contact your distributor if you have any kind of question about your purchase.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>