Alecto SMARTBABY5BK Wi-fi Baby Monitor with Camera Instruction Manual

Alecto SMARTBABY5BK Wi-fi Baby Monitor with Camera

Specifications

• Image Sensor: Shutter
• WDR: Digital WDR
• Video Compression: H.264/H.265
• Bit Rate: 32Kbps~2Mbps
• Audio: Built-in mic/speaker
• Storage: SD card (max. 128G), FI Cloud Storage, NVR
• Wi-Fi: 2.4G WIFI (IEEE802.11 b/g/n)
• Security: HTTP, TCP/IP, DHCP, DNS, RTSP
• Interface Protocol: Private
• Operating System: Android 5.0+ or iOS9.0+
• Operating Temperature:
• Dimensions: 80x60x73mm
• Net Weight: 78g

What’s in the box?

1. Camera unit
2. Power adapter
3. USB cable
4. Mounting screw and wall plug
5. Reset pin
6. Manual

Installation

1. Download the SMART LIFE APP by scanning the QR code provided.
2. Follow the instructions on the app to add the device. You can manually add the device by selecting the “+” icon in the app.
3. Ensure your phone is connected to the same Wi-Fi network as the camera. The network should be 2.4GHz.
4. Reset the camera if necessary by pressing and holding the reset button for 20 seconds until you hear a beep.
5. If the indicator light flashes twice per second, move to step 8. If the light is solid red, proceed to step 7b.
6. Hold the reset button for 6 seconds until the light flashes twice per second, then proceed to step 8.
7. Follow the in-app instructions to connect the camera to your network.

General Warnings and Safety Instructions

• Read and follow all instructions. All safety and operating instructions should be read before use.
• This device cannot replace responsible adult supervision.
• The device is designed for exclusive indoor use.
• Do not expose the units to rain or moisture.
• Keep the device out of the reach of children.
• Be cautious with small parts during unboxing and assembly.
• Keep cables a minimum of 1 meter away from small children.
• Use only the supplied adapters (nominal 5V; 1.0A).
• Do not use the device if the cable or plug is damaged.
• Do not attempt to repair or adjust any of the functions.
• Do not place the product in a closed area where air flow may be obstructed.

Removing a Device

1. To remove a device from the app, go to the device settings and select “Remove Device.”
2. Confirm the removal on the app.

Product Usage Instructions

1. Read and understand the safety and operating instructions before use.
2. This device is intended for indoor use only.
3. A responsible adult should supervise the use of this device.
4. Avoid exposing the unit to rain, moisture, or direct sources of heat.
5. Handle with care when unpacking and assembling the product.
6. Do not attempt to repair or adjust any functions of the device yourself.
7. Place the device in a well-ventilated area to prevent overheating.

Attention Points

• Ensure that the product is within the registration range.
• The product is only compatible with 2.4 GHz Wi-Fi networks.
• Remove the device from the app immediately after installation if it is not going to be used.
• In case of connection problems, you will only receive a message in the app after 30 minutes have passed.

EU Declaration of Conformity

Commaxx declares that the radio equipment type SMARTBABY5 complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://DOC.hesdo.com/SMARTBABY5-DOC.pdf

Manufacturer Information
Commaxx B.V., Wiebachstraat 37, 6466NG Kerkrade, The Netherlands. Official Alecto Home Webshop: www.alectohome.com

FAQ

Where can I find the full text of the EU declaration of conformity?
The full text is available at http://DOC.hesdo.com/SMARTBABY5-DOC.pdf.

Can I use this product outdoors?

No, this product is intended for indoor use only.

What is the maximum storage capacity supported by the SD card?

The device supports SD cards with a maximum capacity of 128GB.

What Wi-Fi standard does the device support?

The device supports 2.4G WIFI (IEEE802.11 b/g/n) standards.

What are the operating system requirements for using this product?

The product is compatible with Android 5.0+ or iOS9.0+ operating systems.

How do I download the SMART LIFE APP?

Scan the QR code provided in the user guide or search for the app in your device's app store.

What should I do if my camera is not connecting?

Ensure your smartphone or tablet is on the same 2.4GHz Wi-Fi network as the camera, then follow the reset and connection instructions provided.

What storage options are available for the SMARTBABY5?

You can use an SD card (max. 128G), FI Cloud Storage, or NVR for storage.

References

• Alecto Home | Official Alecto Home Webshop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>