Peerless-AV STS650 Wall Mount Smart Universal Scissor Instruction Manual
- June 15, 2024
- Peerless-AV
Table of Contents
Peerless-AV STS650 Wall Mount Smart Universal Scissor
Product Specifications
- Model : STS650
- Height Range: 39 – 85 inches (99 – 216 cm)
- Weight Capacity: 200 lb (90.7 kg) MAX
Product Usage Instructions
Assembly Tools Needed:
- 5/32 (4mm) Allen Wrench
- 5/16 (8mm) Allen Wrench
- 3/8 (10mm) Allen Wrench
Assembly Steps:
- Ensure all parts are available as per the Parts List provided.
- Use the 4mm Allen Wrench to tighten screws. Screws must get at least three full turns and fit snugly.
- To properly tighten screws, tighten until screw head makes contact, then tighten another 1/2 turn. Do not overtighten screws.
- When installing on a wood stud wall covered with gypsum board,ensure the wood studs are a minimum of 2 x 4 nominal size and not over 5/8 thick.
- Use a stud finder to locate and mark stud center lines for installation.
WARNING
This product is designed to be installed on wood stud, solid concrete or
cinder block walls. Hardware is included for wood stud, solid concrete and
cinder block installation. Before installing make sure the supporting surface
will support the combined load of the equipment and hardware. Screws must be
tightly secured. Do not overtighten screws or damage can occur and product may
fail. Never exceed the Maximum Load Capacity. Always use an assistant or
mechanical lifting equipment to safely lift and position equipment. This
product is intended for indoor use only. Use of this product outdoors could
lead to product failure or personal injury. Be careful not to pinch fingers
when operating the mount. For support please call customer care at
1-800-865-2112
Symbols
- WARNING
- Skip to step.
- Screws must get at least three full turns and fit snug
- Do not overtighten screws.
- Display center
- Listen
Tools Needed for Assembly
To properly tighten screws: Tighten until screw head makes contact, then tighten another 1/2 turn. Do not overtighten screws.
Parts (Before beginning, make sure you have all the parts shown below).
Description Qty Part #
- A wall plate 1 10015551-RBLK
- B adaptor assembly left 1 10017018
- C adaptor assembly right 1 10017012
- D 8mm concrete anchor 4 590-0320
- E #14 x 2-1/2″ wood screw 4 5S1-015-C03
- F adaptor extension 2 10016914-RBLK
- G 4mm allen wrench (6″ long) 1 560-9646
- H M6 x 12mm socket pin screw 12 520-1050
- I M6 x 25mm socket pin screw 4 520-1211
- J M8 x 12mm socket pin screw 4 520-1724
- K M8 x 25mm socket pin screw 4 520-1101
- L washer 8 540-9406
- M spacer 8 600-1215
- N M8 x 50mm socket pin screw 4 521-1013
- O 4mm allen wrench (18″ long) 1 560-1727
DIMENSION
INSTALLATION INSTRUCTION
Wood stud wall
Concrete/Cinder block.
WARNING
When installing Peerless wall mounts on a wood stud wall covered with
gypsum board (drywall), verify that the wood studs are a minimum of 2″ x 4″
nominal size. Do not install over gypsum board thicker than 5/8″.
Use stud finder to locate and mark stud center lines
1a-2
Level wallplate. Mark mounting holes on stud center lines
1a-3
Drill mounting holes into the supporting surface (2.5″ (64mm) minimum depth
required).
The mounting hole must center on the stud.
1a-4
Level wallplate. Install using woodscrews provided
Maximum 80 in. • lb (9 N.M.).
1b
WARNING: When installing Peerless wall mounts on a concrete wall, the
wall must be at least 8″ thick with a minimum compressive strength of 2000
psi. When installing Peerless wall mounts on a cinder block wall, the cinder
blocks must meet ASTM C-90 specifications and have a minimum nominal width of
8″. Do not drill into mortar joints! Be sure to mount in a solid part of the
block, generally 1″ (25mm) minimum from the side of the block. It is suggested
that a standard electric drill on slow setting is used to drill the hole
instead of a hammer drill to avoid breaking out the back of the hole when
entering a void or cavity. Never attach concrete expansion anchors to concrete
or cinder block covered with plaster, drywall or other finishing material.
1b-1
Level wallplate. Mark mounting holes.
1b-2
Drill mounting holes into the supporting surface (2.5″ (64mm) minimum depth
required).
Do not drill into mortar joints.
1b-3
1b-4
WARNING: Be careful not to pinch fingers when operating the mount.
5 : Center adaptor brackets vertically on back of screen.
10-1: Fully extend for servicing only. Close after servicing
Warranty
Peerless-AV
- 2300 White Oak Circle Aurora, IL 60502, USA
- info@peerless-av.com
- 800-865-2112
- 630-375-5100
Peerless-AV EMEA
- Unit 2, Curo Park
- Frogmore, St. Albans,
- Hertfordshire, AL2 2DD
- United Kingdom
- +44 (0) 1923 200 100
Peerless-AV B.V.
- Papendorpseweg 75 3528 BJ Utrecht The Netherlands
- +31 (0) 70 770 8037
Peerless-AV Latin America
- Av. de las Industrias 413
- Parque Industrial Escobedo
- General Escobedo N.L.,
- México 66062
- +52 (81) 8384-830
© 2023 Peerless Industries, Inc. Peerless-AV® is a registered trademark of Peerless Industries, Inc. All rights reserved. Other parties’ marks are the property of their respective owners.
FAQ
Q: What is the weight capacity of the STS650 model?
A: The STS650 model has a weight capacity of 200 lb (90.7 kg) MAX.
Q: What tools are required for assembly?
A: The assembly requires a 5/32 (4mm), 5/16 (8mm), and 3/8 (10mm) Allen
Wrench.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>