STARLINK RJ45 Mobility Flat Mount Kit Installation Guide
- June 13, 2024
- Starlink
Table of Contents
STARLINK RJ45 Mobility Flat Mount Kit
Specifications
- Product Name: Mobility Mount Kit
- Included in the Box: Mobility Mount, Screwdriver, Lag Screws x4, Bolts x4, Nyloc Nuts x4, Sealing Washers x4
- Recommended Tools: Drill/Impact Driver, Drill Bits (5mm and 9mm), Wrenches (13mm and 14mm), Pen
- Mounting Surface Thickness: Recommended at least 1.5mm
Product Usage Instructions
- Scan the QR code to download the Starlink App.
- Your Starlink needs a clear view of the sky for connectivity with satellites. Use the obstructions tool in the App to select a suitable mounting location. Ensure correct orientation relative to your vehicle.
- Squeeze the release tab and pull it away from its fixed location.
- Identify the installation location on your vehicle. Mark the 4 holes on the mobility mount using a pen. Drill using a 5mm (3/16 in) drill bit.
- Install washers on screws and secure the mount to the surface. Use a 13mm (1/2 in) deep-welled socket for installation.
- Pass the Starlink cable through the mobility mount opening and out the front end.
- Connect the ethernet cable to your Starlink and ensure it is fully inserted. Slide your Starlink into the mount until it clicks into place.
- Drive in the two locking screws until hand tight using a screwdriver.
- If you need to remove your Starlink, back out the locking screws and push down on the release tab while pushing your Starlink away from you.
Frequently Asked Questions
- Q: Do I need any additional tools for installation?
- A: The recommended tools provided in the kit should be sufficient for installation.
- Q: Can I install the mobility mount on any vehicle?
- A: Yes, as long as you ensure a clear view of the sky for connectivity.
What’s in the Box
Recommended Tools
Dimension
SCREW INSTALLATION
Download the Starlink App
- Scan the QR code to download the Starlink App.
- setup.starlink.com
Find Mounting Location
- Your Starlink needs a clear view of the sky so it can stay connected with satellites as they move overheard. Objects that obstruct the connection between your Starlink and the satellite will cause service interruptions. Use the obstructions tool in your App to ensure you have selected a suitable mounting location.
- You will also want to ensure your Starlink is mounted in the correct orientation relative to your vehicle as shown below.
Remove Kickstand
- Squeeze the release tab and pull it away from its fixed location.
Mark the Pilot Holes
- Identify the installation location on your vehicle and mark the location of the 4 holes on your mobility mount using a pen or pencil.
Drill the Pilot Holes
- Drill the holes with a 5 mm (3/16 in) drill bit.
- A mounting surface of at least 1.5mm thick is recommended.
Screw Mount to Surface
- Install a washer on the end of each screw and secure the mount to the surface.
- Using a 13mm (1/2 in) deep-welled socket is recommended.
Route Cable Through Mobility Mount
- Route the Starlink cable through the opening in the mobility mount and out the front end.
Plug-in Cable and Install Starlink
- Plug the ethernet cable into your Starlink and ensure the ethernet cable is fully inserted.
- Slide your Starlink into the mount until it clicks into place.
Secure Mount
- Using the screwdriver, drive in the two locking screws until the hand is tight.
Removing Your Starlink
If you need to remove your Starlink, back out the locking screws. Then push
down on the release tab on the mount while pushing your Starlink away from
you.
BOLT INSTALLATION
Download the Starlink App
- Scan the QR code to download the Starlink App.
- setup.starlink.com
Find Mounting Location
- Your Starlink needs a clear view of the sky so it can stay connected with satellites as they move overheard. Objects that obstruct the connection between your Starlink and the satellite will cause service interruptions. Use the obstructions tool in your App to ensure you have selected a suitable mounting location.
- You will also want to ensure your Starlink is mounted in the correct orientation relative to your vehicle as shown below.
Remove Kickstand
- Squeeze the release tab and pull it away from its fixed location.
Mark the Pilot Holes
- Identify the installation location on your vehicle and mark the location of the 4 holes on your mobility mount using a pen or pencil.
Drill the Pilot Holes
- Drill the holes with a 9 mm (3/8 in) drill bit.
Secure Mount to Surface
- Install a washer on the end of each bolt and insert bolts through the mount and pre-drilled holes. Install a nut on the end of each bolt and secure the mount to the surface.
- Using a 14 mm deep-well socket is recommended.
Route Cable Through Mobility Mount
- Route the Starlink cable through the opening in the mobility mount and out the front end.
Plug-in Cable and Install Starlink
- Plug the ethernet cable into your Starlink and ensure the ethernet cable is fully inserted.
- Slide your Starlink into the mount until it clicks into place.
Secure Mount
- Using the screwdriver, drive in the two locking screws until the hand is tight.
Removing Your Starlink
- If you need to remove your Starlink, back out the locking screws. Then push down on the release tab on the mount while pushing your Starlink away from you.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>