89012 13.7 Inch Angel Brown White Christmas Tree Topper Instruction Manual
- June 9, 2024
- GE
Table of Contents
MODEL NO. 89012
FOR INDDOR USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed
inducing the following:
a) READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use. When predicts are used in outdoor applications, connect the
predict to a Ground Fault Occult Interrupting (GFCI) outlet. It one is not
provided, contact a qualified electrician for proper install atop.
c) This seasonal use product is not intended for permanent installation or
use.
d) Do not mount or place near gas or tetanic heaters, heaters, fireplaces,
candles or other similar sources of heat.
e) Do not secure the wining of the predict with staples or nails, or place on
sharp hooks or nails.
f) Do not let laws rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the right, or
if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns,
personal injury and electric shock it should not be played with or placed
where small chidren can reach it
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other object from odor, wire, or light sting.
k) Do not close doors or windows on the product or extension cords as this may
damage the wire insulation.
l) Do not cover the product with cloth, paper or any matinal not pail of the
product when in use.
m) This product is equipped with push-in type lamps. Do not twist lamps.
n) This product employs overload protection (fuse). A blown fuse indicates an
overload or short -circuit situation. If the tine blows, unplug the product
from the outlet. A so unplug any additional strings or products that may be
attached to the product. Replace the fuse as per the user sinning instructor’s
(follow product mirbane for proper fuse rating) and check the product. If the
replacement fuse blows. a short-ci rant may be present and the product should
be discarded.
o) Read and follow all instructions that are on the product or provided with
the product.
p) SAVE THESE INSTRUCTIONS USE AND CARE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well
maintained and fresh. Do not place on live trees in which the needs are brown
or break off early. Keep the tee holder tiled with water.
b) If the product is placed on a tree, the tree should be well secured and
stable.
c) Before using or reusing, inspect product carefully. Discard any products
that have cut, damaged, or frayed wire insulator) or cords, cracks in the lamp
holders or enclosures, loose connections, or epodes copper wire.
d) When stoning the product, carefully remove the product from wherever it is
placed, including tree, bract has, or bushes, to avoid any undue strain or
stress on the product conductors, connections, and wire.
e) When not in use, store neatly in a cool, dry location protected from
sunlight.
USER SERVICING INSTRUCTIONS
Replace the fuse.
a) Grasp plug and remove from the receptacle or other outlet device. Do not
unplug by pulling on cord.
b) Using a fathead screwdriver, open Use cover. Slide open the tune access
cover on top of attachment plug towards blades.
c) Remove fuses carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided win
product)
e) Close fuse cover. Slide closed the Use access cover on top of attach mint
plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety device fuse
that should not be removed. Discard product if the attach ment plug is
damaged.
Replace the lamp.
- Grasp plug and remove from the receptacle or other outlet deuce. Do not unplug by pulling on cord.
- Pull lamp and plastic base straight out of lamp holder.
- Replace lamp with only 3.3 Volt, 0.066 Watt. LED type lamp (provided with product).
It the new lamp base does not it in lamp holder, follow the steps below step 3.
a) Remove the base of burned out lamp by straighten ng lamp leads and gentry
pull lamp out.
b) Thread leads of new lamp through holes mold base with one lead n each hole.
c) After lamp is fully inserted Into base, bend each lead up, like other lamps
in the light set so that the leads will touch the contacts inside the lamp
holder.
CAUTION:
- Risk at fire. This product does not contain lamp shunts, which allow the product to operate if one lamp burns out. Do not replace lamps with other than the spare lamps provided with this product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received. including interference that may cause uncles red operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B ‘Digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a reside: vial installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. It this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a orcuit cltlerent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For questions and or assistance, call customer service at 1 877 398 7337 or
visit us the web at
www.geholidaylighting.com
©2022 Nicolas Holiday Limited FP 22 PRINTED IN CHINA
246 Spning Hill Road, Unit B. Trumbull CT 06611
9F, No. 37, Guangt North Rd. Taipei. Taiwan 10560
All nghts reserved.
GE is a trademark of General Electric Company and is under license by
Nicolas Holiday Limited
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>