Shark GS500Q Press & Refresh Garment Care System User Manual

Shark GS500Q Press & Refresh Garment Care System User Manual

User’s Guide
GS500Q

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

WHEN USING YOUR SHARK® PRESS & REFRESH™ GARMENT CARE SYSTEM, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING YOUR PRESS & REFRESH™ GARMENT CARE SYSTEM.

DANGER OF SCALDING

Please use caution when using the garment steamer. The Wrinkle Eraser™ pressing bar and the steam emitted are very hot. The Wrinkle Eraser™ is not controlled by the steam trigger and is hot as long as the unit is turned on and for 30 minutes after the unit has been turned off.

POLARIZED PLUG:
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to defeat this safety feature.

1. USE THE SYSTEM ONLY FOR ITS INTENDED USE AS DESCRIBED IN THIS MANUAL.
2. ONLY USE WATER. To extend the life of your Press & Refresh™ Garment Care System, we recommend using distilled water especially if you live in an area with hard tap water.
3. DO NOT add cleaning solutions, scented perfumes, oils, or any other chemicals to the water used in this appliance as this may damage the unit or make it unsafe for use.
4. Use of any substances other than manufacturer’s recommended accessories will automatically void your warranty.
5. DO NOT use outdoors.
6. DO NOT leave the appliance unattended when plugged in.
7. Always unplug the power cord from the electrical outlet when not in use, when filling the water tank and before cleaning.
8. DO NOT allow to be used as a toy.
9. DO NOT put any objects into openings or operate with any opening blocked.
10. DO NOT use on leather, suede, vinyl, plastic or other delicate steam sensitive materials. Always determine the colorfastness of any fabric before using the fabric steamer by testing it on a small portion of the garment’s underside.
11. This appliance and the accessories become hot during use. Exercise care when changing accessories and follow removal and changing instructions as outlined in the manual. Do not change frames while the unit is turned on. Turn the unit off, wait for the Wrinkle Eraser™ to cool, and then change frames.
12. The garment steamer can be used in a vertical or horizontal motion. NEVER hold the steam head down while at rest or tilt it in a backward position as this may result in discharge.

13. When cleaning the garment steamer, unplug the power cord and clean with a dry or damp cloth. DO NOT pour water on the unit or use alcohol, benzene or paint thinner on the unit.
14. NEVER attempt to steam clothing while it is being worn.
15. To protect against a risk of fire, electric shock, or injury:
a. To avoid circuit overload, DO NOT operate another appliance on the same socket (circuit) as the fabric steamer.
b. DO NOT immerse any part of the system in water or other liquids.
c. DO NOT pull power cord to disconnect from outlet; instead, grasp plug and pull to disconnect.
d. DO NOT use extension cords or outlets with inadequate current carrying capacity. If an extension cord is absolutely necessary, use a 15-ampere cord. Cords rated for less amperage may overheat. Use care to arrange the cord so that it cannot be pulled or tripped over.
e. DO NOT operate the system with a damaged cord or plug, or if the appliance or any other part of the system has been dropped or damaged.
f. DO NOT disassemble or attempt to repair the fabric steamer. Return the system to EURO-PRO Operating LLC for examination and repair. Incorrect reassembly or repair can cause a risk of electrical shock or injury to persons when the fabric steamer is used.
g. DO NOT handle plug or fabric steamer with wet hands or operate without shoes.

h. DO NOT pull or carry by power cord, use power cord as a handle, close a door on the power cord, or pull the power cord around sharp corners or edges.
i. DO NOT allow power cord to touch hot surfaces.
j. ALWAYS disconnect system from electrical outlet when filling the water tank or emptying and when not in use.
k. NEVER attempt to fill this unit under a water faucet. Always use the filling flask that is provided.
l. Never turn the appliance over or on its side when in use.
m. NEVER aim or direct steam towards people, animals, or plants. The steam is very hot and can cause burns. Burns can occur from touching hot metal parts, steam, steam bonnets or frames. Use care when you turn a steam appliance upside down – there may be hot water in the reservoir.
n. DO NOT operate the product while under the influence of drugs, alcohol or medications.
o. DO NOT operate in the presence of explosive and/or flammable fumes.
p. Store your appliance indoors in a cool, dry area out of the reach of children.
q. Keep your work area well lit.
r. Let the system cool completely before putting away. Loop cord loosely around the appliance when storing.
s. Keep out of the reach of children.

SAVE THESE INSTRUCTIONS

Welcome to the next wave of garment care!

The Press & Refresh™ Garment Care System brings your fabrics back to life with fewer trips to the dry cleaners! For the first time ever professional steam power in a portable unit.

The professional steam deeply penetrates fibers, renews and freshens fabric. The exclusive heated Wrinkle Eraser™ presses for a crisp finish and dries fibers to prevent re-wrinkling.

Extend the life of your garments and go from not quite ready-to-wear to ready- to-wear in one easy step. The Look Your Best Guide provides step-by-step tips for all of your garment care needs.

Attaching the appropriate accessory:
The unit comes assembled with a small steam bonnet attached. The bonnet must be attached at all times when the unit is being used.
1. Attach the desired frame
2. Using both hands, hold the frame on either side. Attach the top of the frame to the unit above the Wrinkle Eraser™  into the notch. Next, secure the pointed end of the frame around the bottom of the unit and snap into place (Fig. 1). The seam of the frame must line up against the seam of the unit for proper use.

3. To remove the frame, gently pull on the pointed end and lift the frame off the unit.

TIP: Wipe away condensation from the steam guard on the bottom of the frame after extended use.

FRAME/ACCESSORY

Small Steam Bonnet|
---|---
Bristle Brush Frame|
Lint Brush Frame|
Upholstery/Delicate
Fabric Frame & Delicate Steam Bonnet|
Upholstery/Delicate
Fabric Frame & Upholstery Steam Bonnet|

Helpful Tips on using the Vertical Press Pad and VELCRO® Clips:

1. For the first time ever, the vertical press pad eliminates the need for an ironing board. It is designed to fit on any size door, and can remain setup for your convenience. The VELCRO® clips are used to position & stretch the garment for quick steaming with better results to complete the garment care system
(Fig. 2).

2. To make pressing easier, the vertical press pad has two hooks on either end to hang your garment from for larger pressing surface.

specially designed multi layered honeycomb pad protects fabrics from water marks and water impurities
Best for: cotton, wool, linen, denim| Improves steam penetration on heavy fabrics without leaving water marks
Best for: cotton, wool, rayon, polyester, silk, satin, cashmere and blends| Removes lint, pet hair, and other debris while steaming and pressing
Best for: lace, velvet, silk, satin, embelished or delicate garments| Specifically designed to protect delicate fabric from high heat
Best for: bedding, mattress, curtains, baby bedding, plush toys, high chairs, car seats, sofa, and arm chairs| Shaggy material acts like multiple fingers to pick up dust and deodorize while steaming. It provides a large pocket of hot steam

This manual covers model number:

GS500Q

TECHNICAL SPECIFICATIONS

Voltage: 120V., 60Hz.
Power: 1580 W
Water Capacity: 200 mL (6.5 fl. oz.)

Thank you for purchasing the Shark® Press & Refresh™ Garment Care System.

Getting Started

The Press & Refresh™ Garment Care System provides a complete process for all of your garment care needs. Save time and money with fewer trips to the dry cleaners and have your garments ready-to-wear when you want.

The combination of professional steam power and the exclusive heated Wrinkle Eraser™ makes it easier than ever to care for your garments. The Press & Refresh™ comes complete with accessories for all garment care needs. The vertical press pad eliminates the hassle of an ironing board and makes it easy to steam and press right on the hangers.

Not only great on garments, the Press & Refresh™ can be used to refresh fabrics throughout your home. Now you can easily reduce odors, sanitize fabric and help eliminate dust mites. The extra long 15 foot power cord makes it easy to navigate around your home.

First things first, you need to know what’s in the box you just opened:

a. Garment Steamer
b. 2 Small Steam Bonnet (one is attached to the unit)
c. Bristle Brush Frame
d. Upholstery/Delicate Fabric Frame
e. Lint Brush Frame
f. Upholstery Steam Bonnet
g. Delicate Steam Bonnet
h. Vertical Press Pad
i. 2 Support Rods (assembled in the vertical press pad)
j. Garment Hook
k. 8 Heat Protection Panels (assembled in vertical press pad)
l. 3 VELCRO® Clips
m. Filling Flask

VELCRO® is a registered trademark of Velcro Industries B.V.

IMPORTANT: Always check the fabric care labels for recommendations. Test the fabrics for colorfastness in an inconspicuous place such as an inside seam. Some articles of clothing are better steamed from the underside.

IMPORTANT: When assembling your garment steamer, there may be a little water in the water tank. This is because we test all our garment steamers 100% before you buy them, so you get a quality Shark® Steam product.

Assembly of the Vertical Press Pad

Assembly & use instructions:

1. Remove contents of the Press & Refresh™ Garment Care System and lay them out on a flat surface to see that you have all the components to complete the assembly.

2. READ ALL INSTRUCTIONS BEFORE USING YOUR PRESS & REFRESH™ GARMENT CARE SYSTEM.

IMPORTANT: Always make sure the garment steamer is UNPLUGGED from the electrical outlet when not in use. Never fill the water reservoir when the unit is plugged in.

Assembling the vertical press pad:

3. I nsert the garment hook into the opening at the top of the vertical press pad (Fig. 1). Secure the rod into the garment hook on either side of the pad making sure they are inserted firmly (Fig. 2). The support rods come assembled in the pad.

4. The Vertical Press Pad comes asembled with heat protection panels in the pockets on the back. These panels protect your door from heat damage and should be in place at all times during use.

5. Attach the vertical press pad to any door. With the door open, loop the straps at the top of the vertical press pad around the corner of the door and repeat on the opposite side. Gently tug on the pad to make sure it is secure and shut the door completely to ensure the pad is stable for pressing. Be careful not to close the door on your fingers. Adjust the straps to the appropriate height for comfort (Fig. 3).

Care instructions:

6. Remove the 8 heat protection panels from the back of the pad and remove the garment hook and rods. Machine wash in warm water with liquid detergent and lay flat to dry. Do not use bleach or fabric softener.

Using Your Press & Refresh™

Filling and refilling the water reservoir:

1. Never fill the garment steamer while it is plugged into an electrical outlet.

2. Open the water cap and hold the the garment steamer horizontally with the Wrinkle Eraser™ parallel to the floor. Using the filling flask provided fill the water tank to the Max Fill line. Be careful not to overfill. Push the cap back into place, making sure it closes firmly (Fig. 1).

NOTE: The water tank does not have to be completely full for the fabric steamer to generate steam. However, make sure that the water tank is at least half way full for optimal results.

Attaching the accessories:

IMPORTANT: Use caution when changing the frames when the unit is hot. The frames are designed with a steam guard around the bottom to provide protection from heat when placing or removing the frames.

The small steam bonnet must be attached at all times during usage.
The bonnet should only be removed for washing by hand, if necessary (see page 13 for care instructions).

3. Choose your desired frame.

Using both hands, hold the frame on either side. Attach the top of the frame to the unit above the Wrinkle Eraser™ into the notch. Next, secure the pointed end of the frame around the bottom of the unit and snap into place (Fig. 2).

When using the upholstery/delicate fabric frame:

NOTE: Remember, DO NOT use the garment steamer without the small steam bonnet in place

4. Attach the desired bonnet to the frame, then attach the frame to the unit. Pull either side of the bonnet over the top of the frame and secure the bottom of the bonnet to the frame (Fig. 3). Then attach the frame to the garment steamer as described above (Fig. 4).

Hold the steam trigger for continuous steam. The steam will stop emiting once you let go of the button.
Wipe away condensation from the frame with extended use.

Using the Press & Refresh™ and vertical press pad:

CAUTION: The Wrinkle Eraser™ is not controlled by the steam trigger and is hot as long as the unit is turned on.
CAUTION: Do not over tilt the unit when steaming overhead.
CAUTION: Do not hold the unit in a fixed position on delicate fabrics and upholstered items.
CAUTION: The Wrinkle Eraser™ is hot. Use caution when removing the frames. DO NOT put your hands directly onto the Wrinkle Eraser™.
WARNING : Never steam any article of clothing while it is being worn.

1. Hang the vertical press pad on a door.
2. Hang the garment onto the garment hook.

3. Once the selected attachment is placed on the garment steamer, turn the On/Off switch to the “I” position, a blue LED light will illuminate. It will take approximately 1 minute for the unit to heat up.

4. Holding the garment steamer in the vertical position with the steam nozzle pointing away from you, press and hold the steam trigger for continuous steam and begin steaming your garments in a vertical motion. Begin at the top of the garment and move in a up and down direction pressing the Wrinkle Eraser™ directly onto the fabric.

5. You can use the hooks on either side of the vertical press pad for a larger pressing area.

6. When steaming lightweight garments, the VELCRO® clips can be used in place of a hanger to attach a garment directly to the pad.

7. When finished using the garment steamer, turn the appliance “O” and let it cool before emptying the water tank and removing the bonnets and frames if necessary.

Using the Press & Refresh™ horizontally:

8. The Press & Refresh™ can be used to deodorize, sanitize, and refresh upholstered items: sofa, baby bedding, mattress, car seat, drapes, and more.

9. Attach the upholstery/delicate frame and upholstery steam bonnet to the unit.

10. In a horizontal position, move the steamer in a up and down motion continuously over the upholstered item.

When to use the different accessories:

1. Small Steam Bonnet – must be in place over steam nozzle during all usage.

TIP: Provides evenly distribution of steam and protects fabrics from watermarks and impurities in water .

2. Bristle Brush Frame – Offers better steam penetration for heavy fabrics without leaving water marks.

Fabric Recommendations: Heavy fabrics, cotton, wool, canvas, denim.

CAUTION: Do not use the bristle brush on delicate fabrics.

3. Lint Brush Frame – use to remove hair, lint and pet fur while steaming your garments.

4. Upholstery/Delicate Fabric Frame & Delicate Steam Bonnet – provides extra protection for delicate fabrics when the Wrinkle Eraser™ is not necessary while freshening fabrics.

Fabric Recommendations: Silk, satin, embellished garments.

TIP: Some garments have better results when steamed from the inside or turned inside out. Slightly tug the bottom of the garment and hold at an angle.

5. Upholstery/Delicate Fabric Frame & Upholstery Steam Bonnet – shaggy material acts like multiple fingers to pick up dust and deodorize while steaming. It provides a large pocket of hot steam.

6. VELCRO® Clips – Easy detachable clips can be used to hold lightweight garments directly on to the pad and to position & stretch the garment for quick steaming with better results.

7. Vertical Press Pad – Creates a vertical ironing board anywhere in the home. The Vertical Press Pad can be used on any door and is virtually invisible when the door is closed for easy access to the pad for last minute touch ups.

Care of Your Press & Refresh™

Cleaning & storing

1. Turn the garment steamer off “O”.
2. Unplug the appliance from the electrical outlet.
3. Let the appliance cool completely for approximately 30 minutes.

4. Empty the water from the water tank.
5. Wipe the exterior of the garment steamer with a damp cloth and wipe dry if needed.

6. Bundle up the power cord and secure it with the VELCRO® strap that is attached to the power cord. Always store your appliance in a cool, dry area.

Care & use of the small steam bonnet frame

7. The steam bonnet helps filter impurities from your water. It might become slightly discolored over time.

8. Let the steamer cool completely before removing the bonnet. Gently pull on either side of the bonnet to remove from the steam nozzle.

9. Hand wash the bonnet in cold water with a mild detergent and let air dry completely before using again. Do not dry in clothes dryer.

10. To re-attach the bonnet, pull one corner of the bonnet over the steam nozzle then the other corner. Secure the bottom of the bonnet to the nozzle using the bottom tab.

Troubleshooting Guide

is lit. If not, check that the unit is plugged in and the on/off button is raised and in the on “I” position.

Verify that the water tank is at least half way full or fill to the max fill line.

The nozzle leaves water drops on the garment.| You are not using the steam bonnet.
The steam bonnet is too wet.
The frame has condensation.| The small steam bonnet must be in place
at all times during usage.

The bonnet prevents water drops being left on the garment and to removes impurities from your water.

Let the unit cool for 30 minutes, remove the steam bonnet and let it dry out before using again or replace with a new bonnet frame.

Let the appliance cool and wipe the frame off.

Euro-Pro One (1) Year Limited Warranty

EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions.

If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid to:

U.S.: EURO-PRO Operating LLC
For customer service support call 1-800-798-7398

If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and a check made payable to EURO-PRO Operating LLC in the amount of $14.95 to cover the cost of return shipping and handling must be included.*

Non-durable parts including, without limitation, filters, brushes and electrical parts which normally require replacement are specifically excluded from warranty.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.

This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem
with item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>