VELP SCIENTIFICA F203A0440 MST Magnetic Stirrer Instruction Manual

June 8, 2024
VELP SCIENTIFICA

F203A0440 MST Magnetic Stirrer
Instruction Manual
VELP SCIENTIFICA F203A0440 MST Magnetic
Stirrer

General Information

Before using the unit, please read the following instruction manual carefully.
Do not dispose of this equipment as urban waste, in accordance with EEC directive 2002/96/CE.
This unit must be used for laboratory applications indoor only. The manufacturer declines all responsibility for any use of the unit that does not comply with these instructions. If the product is used in a not specified way by the manufacturer or with non specified accessories, product’s safety may be compromised.

This unit has been designed and manufactured in compliance with the following standards:
Safety requirements for electrical equipment for measurement, control and for laboratory use
IEC/EN 61010-1
IEC/EN 61010-2-051
Electrical equipment for laboratory use: UL 61010-1
General requirement – Canadian electrical code:  UL 61010-1
VELP reserves the right to modify the characteristics of its products with the aim to constantly improving their quality.

Safety Regulations

The plug disconnects the instrument. Therefore, place the instrument where it can be quickly disconnected.
Place the power supply in the way to avoid liquid spills directly on it.
The stirred solution may release toxic, dangerous or poisonous gases. Adequate safety measures must be taken, in accordance with the safety regulations in force, including the presence of hood and personal protective equipment (masks, gloves, goggles, etc.).
Position the instrument on a flat surface, with a distance from the wall of 30 cm (at least).
Do not use with explosive and dangerous materials for which the equipment is not designed. The stirrer must not be used in explosive atmospheres.
It is responsibility of the user appropriately decontaminate the instrument in case of dangerous substances fall on or in it. It is also responsibility of the user to use safety substances for cleaning or decontaminating, which do not react with internal parts of the instrument or with the material contained in it. In case of doubts on the compatibility of a cleaning solution, contact the manufacturer or local distributor.
Do not use with explosive and dangerous materials for which the equipment is not designed. The stirrer must not be used in explosive atmospheres, in bain- marie and to stir combustible liquids that have a low combustion temperature. The minimum fire point of flammable solution is 200 °C. Only small amounts (< 50 ml) of flammable liquid can be used with the device.
In case of black-out, once the power is back the device will restart automatically.

Introduction

The MST magnetic stirrer is a small, simple and effective stirrer. Thanks to the white cover surface it is specially designed for microtitrations, and it is extremely useful where reliable and small instrument is needed. The stirrer stays cold even after several days of continuous use. This feature makes it highly appreciated in microbiology and biochemistry.
NOTE: it’s important to choose the most suitable magnetic stirring bar related to the quantity and the liquid to be stirred as well as to the type of the beaker. The magnetic stirring bar that satisfies most of the application is A00001056 (6x35mm).

Assembly and installation

Upon receipt and after having removed the packaging, please check the integrity of the instrument. The box includes:

  • Magnetic stirrer MST
  • Plug for power supply
  • Switching VELP 100-240V/12V without plug
  • Instruction manual

2.1 Electrical connection
After having unpacked the instrument, place the unit on the laboratory bench.
Before connecting the instrument to the power supply, make sure that the values on the rating plate correspond to those of the power supply. Connect the unit to the power supply using the transformer supplied.
Ensure that the socket and the relative cut-off device conform to current safety norms and easy to reach.
2.2 Start-up
Rotate the speed knob completely to the left. Place the flasks containing the sample and a suitable magnetic stirring bar on the stirring plate. Then, set the speed by turning the speed knob.

Operating controls

VELP SCIENTIFICA F203A0440 MST Magnetic Stirrer - Operating
controls

Turn the stirring speed knob on the front panel in order to start the stirring function.
It is possible to select speeds between 0 and 1100 rpm.
When the led is lighted it means that the stirring is on

Maintenance

No routine or extraordinary maintenance is necessary apart from periodically cleaning the unit as described in this manual. In compliance with the product guarantee law, repairs to our units must be carried out in our factory, unless previously agreed otherwise with local distributors. The instrument must be transported in its original packaging and any indications present on the original packaging must be followed (e.g. palletized). It is the responsibility of the user, to properly decontaminate the unit in case of hazardous substances remaining on the surface or interior of the device. If in doubt about the compatibility of a cleaning or decontamination product, contact the manufacturer or distributor.
4.1 Cleaning
Disconnect the unit from the power supply and use a cloth dampened with an non-inflammable non-aggressive detergent.

Technical data

Admitted power supply 0.5 A / 100-240 V / 50-60 Hz (+/-10%)
Power 12 Vdc 1.5 W
Dimensions (WxHxD) 130x50x150 mm (5.11×1.96×5.9 in)
Weight (with plug) 0.4 kg
Speed range 0 ÷ 1100 rpm
Operating mode Continuous
Construction material PA
Environmental ambient temperature 5 – 40 °C (41 – 104°F)
Storage temperature range -10… + 60 °C (14 – 140°F)
Pollution degree 2
Overvoltage category II
Sound level 35 dBa
Max humidity 80%
Altitude Up to 2000 m.

Accessories/Spare parts

A00001056 Stirring bar 6x35mm
10000234 Bumpon D. 12mm
A00001057 Stirring bar 6x20mm
10003081 Power supply 100-240V/12V no plug
10005213 Blue knob

Wiring diagram

VELP SCIENTIFICA F203A0440 MST Magnetic Stirrer - Wiring
diagram

  1. External power supply
  2. Socket of the instrument
  3. Electronic board
  4. Potentiometer for speed regulation
  5. Electric motor

Declaration of conformity ****

We, the manufacturer VELP Scientifica, under our responsibility declare that the product is manufactured in conformity with the following standards:
EN 61010-1
EN 61326-1
2015/863/EU (RoHS III)
2012/19/EU (WEEE)
EN 61010-2-051
and satisfies the essential requirements of the following directives:

  • Machinery directive 2006/42/EC
  • Electromagnetic compatibility directive 2014/30/EU
  • plus modifications

Declaration of conformity
We, the manufacturer VELP Scientifica, under our responsibility declare that the product is manufactured in conformity with the following regulations:
S.I. 2016/1101 Electrical Equipment (Safety) Regulations 2016
S.I. 2016/1091 Electromagnetic Compatibility Regulations 2016
according to the relevant designated standards:
EN 61010-1
Safety requirements for electrical equipment for measurement, control, and laboratory use Part 1: General requirements
EN 61010-2-051 Particular requirements for laboratory equipment for mixing and stirring
EN 61326-1
Electrical equipment for measurement, control and laboratory use – EMC requirements – Part 1: General requirements
and satisfies the essential requirements of regulations:
S.I. 2008/1597 Supply of Machinery (Safety) Regulations 2008
S.I. 2012/3032 Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012
S.I. 2013/3113 Waste Electrical and Electronic Equipment Regulations 2013 plus modifications.

Thank you for having chosen VELP!
Established in 1983, VELP is today one of the world’s leading manufacturer of analytical instruments and laboratory equipment that has made an impact on the world-wide market with Italian products renowned for innovation, design and premium connectivity. VELP works according to ISO 9001, ISO14001 and OHSAS 18001 Quality System Certification.
Our instruments are manufactured in Italy according to the IEC 1010-1 and CE regulation.
Our product lines:

Analytical instruments
Elemental Analyzers
Digestion Units
Distillation Units
Solvent Extractors
Fiber Analyzers
Dietary Fiber Analyzers
Oxidation Stability Reactor
Consumables| Laboratory Equipment
Magnetic Stirrers
Heating Magnetic Stirrers
Heating Plates
Overhead stirrers
Vortex mixers
Homogenizers
COD Thermoreactors
BOD and Respirometers
Cooled Incubators
Flocculators
Overhead Shakers
Turbidimeter
Radiation Detector
Open Circulating Baths
Pumps
---|---

www.velp.com
VELP Scientifica Srl
20865 Usmate (MB) ITALY
Via Stazione, 16
Tel. +39 039 62 88 11
Fax. +39 039 62 88 120
We respect the environment by printing our manuals on recycled paper.
Distributed by:
10007112/A4

Documents / Resources

| VELP SCIENTIFICA F203A0440 MST Magnetic Stirrer [pdf] Instruction Manual
F203A0440 MST Magnetic Stirrer, F203A0440, MST Magnetic Stirrer, Magnetic Stirrer, Stirrer
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals