VELP SCIENTIFICA F204A0167 AMI Illuminated Magnetic Stirrer Instruction Manual
- June 8, 2024
- VELP SCIENTIFICA
Table of Contents
F204A0167 AMI Illuminated Magnetic Stirrer
Instruction Manual
General Information
Before using the unit, please read the following instruction manual carefully.
Do not dispose of this equipment as urban waste, in accordance with EEC
directive 2002/96/CE.
This unit must be used for laboratory applications indoor only. The
manufacturer declines all responsibility for any use of the unit that does not
comply with these instructions. If the product is used in a not specified way
by the manufacturer or with non specified accessories, product’s safety may be
compromised.
This unit has been designed and manufactured in compliance with the
following standards:
Safety requirements for electrical equipment for measurement, control and for
laboratory use:
IEC/EN 61010-1
IEC/EN 61010-2-051
Electrical equipment for laboratory use: UL 61010-1
General requirement – Canadian electrical code: CAN/CSA-C22.2 No.61010-1
VELP reserves the right to modify the characteristics of its products with the
aim to constantly improving their quality.
Safety Regulations
The plug disconnects the instrument. Therefore, place the instrument where it
can be quickly disconnected.
Place the power supply in the way to avoid liquid spills directly on it.
The stirred solution may release toxic, dangerous or poisonous gases. Adequate
safety measures must be taken, in accordance with the safety regulations in
force, including the presence of hood and personal protective equipment
(masks, gloves, goggles, etc.).
Position the instrument on a flat surface, with a distance from the wall of 30
cm (at least).
It is responsibility of the user appropriately decontaminate the instrument in
case of dangerous substances fall on or in it. It is also responsibility of
the user to use safety substances for cleaning or decontaminating, which do
not react with internal parts of the instrument or with the material contained
in it. In case of doubts on the compatibility of a cleaning solution, contact
the manufacturer or local distributor.
Do not use with explosive and dangerous materials for which the equipment is
not designed. The stirrer must not be used in explosive atmospheres, in bain-
marie and to stir combustible liquids that have a low combustion temperature.
The minimum fire point of flammable solution is 200 °C. Only small amounts (<
50 ml) of flammable liquid can be used with the device.
In case of black-out, once the power is back the device will restart
automatically.
Introduction
AMI is specially designed for titrations, and particularly for those in which
optimum lighting condition are needed in order to see the final point of
colour change well. This magnetic stirrer is illuminated.
The lighted stirrer plate is particularly recommended for titrations that have
weak colour changes during conversion. By the switch it’s possible turn on the
lighted stirrer plate. The stirrer stays cold even after several days of
continuous use. This feature makes it highly appreciated in microbiology and
biochemistry.
NOTE: it is advisable to choose the most suitable magnetic stir bar in
relation to the quantity and characteristics of the liquid and the type of
vessel used. The stirring bar which satisfies most application is code
A00001056 (6x35mm).
Assembly and installation
Upon receipt and after having removed the packaging, please check the integrity of the instrument. The box includes:
- Magnetic stirrer AMI
- Switching power supply 100 – 240 V/12 V
- Instruction manual
2.1 Electrical connection
After having unpacked the instrument, place the unit on the laboratory bench.
Before connecting the instrument to the power supply, make sure that the
values on the rating plate correspond to those of the power supply. Connect
the unit to the power supply using the transformer supplied.
Ensure that the socket and the relative cut-off device conform to current
safety norms and easy to reach.
2.2 Start-up
Rotate the speed knob completely to the left. Place the flask containing the
sample and a suitable magnetic stirring bar on the stirring plate. Then, set
the speed by turning the speed knob.
Operating controls
Turn the stirring speed knob on the front panel in order to start the stirring function. The Stirrer Led shows when the stirring is running. The instrument is equipped with a hole in the bottom through which it’s possible to modify the illumination brightness using a flat screw driver.
Maintenance
No routine or extraordinary maintenance is necessary apart from periodically
cleaning the unit as described in this manual. In compliance with the product
guarantee law, repairs to our units must be carried out in our factory, unless
previously agreed otherwise with local distributors. The instrument must be
transported in its original packaging and any indications present on the
original packaging must be followed (e.g. palletized).
It is the responsibility of the user, to properly decontaminate the unit in
case of hazardous substances remaining on the surface or interior of the
device. If in doubt about the compatibility of a cleaning or decontamination
product, contact the manufacturer or distributor.
4.1 Cleaning
Disconnect the unit from the power supply and use a cloth dampened with an
non-inflammable non-aggressive detergent.
Technical data
Power | 12 Vdc 4 W |
---|---|
Admitted power supply | 0.5 A / 100-240 V / 50-60 Hz (+/-10%) |
Dimensions (WxHxD) | 150x55x270 mm |
Weight (with plug) | 1.2 kg |
Speed range | Up to 1100 rpm |
Illumination range | 1500 ÷ 20000 lx (default value 20000 lx) |
Stirring capacity | Up to 5 liter |
Operating mode | Continuous |
Construction material | Epoxy painted metal structure |
Environmental ambient temperature | 5 – 40 °C (41 – 104°F) |
Storage temperature range | -10… + 60 °C (14 – 140°F) |
Pollution degree | 2 |
Overvoltage category | II |
Sound level | 35 dBa |
Max humidity | 80% |
Altitude | Up to 2000 m. |
Accessories/Spare parts
A00001056 | Stirring bar 6x35mm |
---|---|
10003081 | Power supply 100-240V/12V no plug |
10002097 | Knob |
A00001057 | Stirring bar 6x20mm |
10000231 | Foot |
Wiring diagram
- External power supply
- Socket of the instrument
- Electronic board
- Potentiometer
- Electric motor
- ON-OFF switch
- Led
Declaration of conformity ****
We, the manufacturer VELP Scientifica, under our responsibility declare that
the product is manufactured in conformity with the following standards:
EN 61010-1
EN 61326-1
2015/863/EU (RoHS III)
2012/19/EU (WEEE)
EN 61010-2-051
and satisfies the essential requirements of the following directives:
- Machinery directive 2006/42/EC
- Electromagnetic compatibility directive 2014/30/EU
- plus modifications
Declaration of conformity
We, the manufacturer VELP Scientifica, under our responsibility declare that
the product is manufactured in conformity with the following regulations:
S.I. 2016/1101: Electrical Equipment (Safety) Regulations 2016
S.I. 2016/1091: Electromagnetic Compatibility Regulations 2016
according to the relevant designated standards:
EN 61010-1: Safety requirements for electrical equipment for measurement,
control, and laboratory use Part 1: General requirements
EN 61010-2-051: Particular requirements for laboratory equipment for mixing
and stirring
EN 61326-1: Electrical equipment for measurement, control and laboratory use –
EMC requirements – Part 1: General requirements
and satisfies the essential requirements of regulations:
S.I. 2008/1597: Supply of Machinery (Safety) Regulations 2008
S.I. 2012/3032: Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment Regulations 2012
S.I. 2013/3113: Waste Electrical and Electronic Equipment Regulations 2013
plus modifications.
Thank you for having chosen VELP!
Established in 1983, VELP is today one of the world’s leading manufacturer of
analytical instruments and laboratory equipment that has made an impact on the
world-wide market with Italian products renowned for innovation, design and
premium connectivity. VELP works according to ISO 9001, ISO14001 and OHSAS
18001 Quality System Certification.
Our instruments are manufactured in Italy according to the IEC 1010-1 and CE
regulation.
Our product lines:
Analytical instruments
Elemental Analyzers
Digestion Units
Distillation Units
Solvent Extractors
Fiber Analyzers
Dietary Fiber Analyzers
Oxidation Stability Reactor
Consumables| Laboratory Equipment
Magnetic Stirrers
Heating Magnetic Stirrers
Heating Plates
Overhead stirrers
Vortex mixers
Homogenizers
COD Thermoreactors
BOD and Respirometers
Cooled Incubators
Flocculators
Overhead Shakers
Turbidimeter
Radiation Detector
Open Circulating Baths
Pumps
---|---
Distributed by:
www.velp.com
VELP Scientifica Srl
20865 Usmate (MB) ITALY
Via Stazione, 16
Tel. +39 039 62 88 11
Fax. +39 039 62 88 120 We respect the environment by printing our manuals
on recycled paper.
10003608/B3
Documents / Resources
| VELP
SCIENTIFICA F204A0167 AMI Illuminated Magnetic
Stirrer
[pdf] Instruction Manual
F204A0167, AMI Illuminated Magnetic Stirrer, Magnetic Stirrer, AMI Illuminated
Stirrer, Stirrer
---|---
References
- Avviso di reindirizzamento
- Velp Scientifica, Analytical Instruments, Elemental Analyzers, Digestion Units, Distillation Units, Solvent Extractors, Fiber Analyzers, Dietary Fiber Analyzers, Oxidation Stability Reactor, Consumables Laboratory Equipment, Magnetic Stirrers, Heating Magn
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>