Harbor Breeze ZDL1141-LED5K8030 LED Path Light Instruction Manual
- June 8, 2024
- Harbor Breeze
Table of Contents
ZDL1141-LED5K8030 LED Path Light
Instruction Manual
HARBOR BREEZE and logo design are trademarks or registered trademarks of LF,
LLC. All rights reserved.
Thank you for purchasing this Harbor Breeze product. We’ve created these easy-
to-follow instructions to ensure you spend your time enjoying the product
instead of putting it together. But, if you need more information than what
is provided here, please visit Lowes.com, search the item number and refer to
the Guides & Documents tab on the product’s page.
If you have any questions or problems, please call our customer service
department at 1-888-251-1003, 8 a.m. –
8 p.m., EST, Monday – Sunday. You could also contact us at
partsplus@lowes.com or visit
www.lowespartsplus.com.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list. If any part is missing or damaged, do not
attempt to assemble the product.
No tools required
FEELING CONFIDENT? START YOUR NEXT PROJECT/CONFIANT
Visit www.lowes.com for more information
Printed in China
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| The light does not turn on at night. | 1. The transformer is not plugged in or |
turned on.
2. Fixture connector is not properly installed
on the low voltage cable.| 1. Make sure the transformer is plugged in and
turned on.
2. Make sure the contact pins pierce the wire insulation and make proper
contact with the wire.
CARE AND MAINTENANCE
Clean the lens, lamp head and lamp stand regularly with a non-abrasive
cleaner.
Warning: Always make sure the light is unplugged and completely cool
before attempting to clean it.
WARRANTY
This fixture is warranted to be free from defects in materials and workmanship for five (5) years from the date of original purchase. Call 1-888-251-1003 to obtain a Return Authorization number and further instructions. The manufacturer will be liable for the replacement of the defective item and will not be liable for any other loss, damage, or injury which is caused by the product.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
CAUTION
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more of the following
measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio.
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. -
This product is not a toy and must not be operated by children.
-
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
-
Do not submerge in water. The product can be damaged.
-
Use with 18AWG minimum, underground low-voltage circuit cord.
-
AWG d’au moins 18.
WARNING
- Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
- For use with low-voltage landscape lighting systems only.
- The wire is intended for shallow burial, less than 6 in. deep.
- Risk of Electric Shock. Install all luminaires 10 ft. or more from a pool, spa or foundation.
- Keep lamp away from material that may burn.
- Do not touch hot lens, guard or hot fixture housing.
- Do not operate or install a fixture with missing or damaged parts.
- Do not touch the LED at any time as this may cause damage to the fixture.
INSTALLATION OVERVIEW
PACKAGE CONTENTS
Insert wire from low-voltage transformer (sold separately) into the wire guide by twisting the wire into each end of the wire guide. Align the pins on the connector top cover so that each pin lines up with opposite sides of the wire. Securely tighten the connector top cover making sure the pins completely pierce the plastic shield of the wire.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>