JBL BASSPRO GO Auto Subwoofer and Draagbare Bluetooth Speaker Owner’s Manual

JBL BASSPRO GO Auto Subwoofer and Draagbare Bluetooth Speaker

THANK YOU FOR YOUR PURCHASE . . .
Your product has been designed to provide you the performance and ease of operation you expect from JBL. Take time to read this manual before operating or installing your BassPro Go. This manual describes general installation guidelines and operation instructions. Please note that proper installation of mobile audio components requires qualified experience with mechanical and electrical procedures. If you do not have the knowledge and tools to perform this installation, we strongly recommend consulting an authorized JBL dealer about your installation options.

PRODUCT DESCRIPTION

JBL BassPro Go is a powered subwoofer designed to easily mount and charge in any vehicle. It acts as a subwoofer or a full-range speaker in the vehicle; and, with its quick-disconnect feature, becomes a portable Bluetooth speaker. It features easy-to-use controls and a convenient safety cover to help protect the speaker when used out of the vehicle and to provide an IPx5 marine rating.

WHAT’S IN THE BOX

• 1x portable speaker
• 1x vehicle mounting dock
• 1x wiring harness with in-line fuse
• 1x remote bass controller
• 2x high-level input adapters
• 1x spare fuse
• Mounting hardware
• 2x JBL stickers
• 1x owner’s manual

INSTALLATION AND WIRING

IMPORTANT: Disconnect the vehicle’s negative (–) battery terminal before beginning the installation.

• Wear protective eyewear when using tools.
• Choose a safe mounting location. Check clearances on both sides of the location. Be sure that screws will not puncture brake or fuel lines or wiring harnesses, and that wire routing will not interfere with vehicle operation. Use caution when drilling or cutting.
• When making electrical connections, make sure they are secure and properly insulated.
• Using the dock as a template, mark the locations of the holes on the mounting surface.
• Drill pilot holes in the mounting surface.
• Attach the dock to the mounting surface with the included sheet metal screws and washers.

Mounting the dock in the vehicle
Use the included sheet metal screws to secure the dock to the mounting surface in the vehicle. Ensure that the included wire is long enough to reach the desired mounting location before securing the dock.

Mounting the speaker in the dock

1. Pull the handle out.
2. Rest one corner of the speaker on the dock at a slight angle to get the speaker seated.
3. Rotate the speaker until it is completely in place in the dock.
4. Release the handle to finish securing in place.
   NOTE: It will be easiest to connect the wire harness before mounting the speaker in the dock.

Power and Ground Connections in the vehicle

1. Power: Connect the red +12V power wire in the wire harness to the positive terminal of the vehicle battery. Install a 20A fuse and fuse holder within 18″ (457mm) of the battery.

2. Ground: Connect the black GND wire in the wire harness to bare metal of the vehicle’s chassis, such as at a seat belt bolt.
   NOTE: If possible, remove any paint from the chassis for best contact. It is recommended to use a star washer below the ring connector for a secure connection.

3. Remote-In: Connect the blue remote turn-on wire in the wire harness to the “Remote Out” lead of the source unit, if using low-level signal inputs.

NOTE: 12V ACC turn-on is the preferred method. If you are using high- level signal inputs (vehicle speaker wires), you can choose to have the DC offset feature or the audio-sensing feature turn the amplifier on. You will not have to connect the remote turn-on wire and can terminate the connection.

Power/Protect indicators when connected to the vehicle

• The power button on the control panel indicates the speaker’s modes of operation.

Red

| Protect mode (over/under voltage/short circuit/amplifier circuit failure/excessive heat)
Yellow| Settings mode

Signal input in the vehicle
Line-level inputs: If your source unit offers preamp outputs, connect them to the RCA inputs in the wire harness. Use front or rear preamp outputs for full- range operation, or subwoofer preamp outputs (if available) for subwoofer mode.

Note: When using low-level signals and remote turn-on lead, set the “Auto Turn-on” switch to “12V,” and set the speaker’s input level to “LO”in the settings menu (see “setting the input level”). Set the “Auto-on” switch to 2V, 4V, or 6V, whichever most closely matches the voltage of your source unit’s preamp outputs.

High-level inputs: If your source unit does not have line-level outputs, use the supplied high-level input adapters to connect to the speaker output wires of your source unit to the RCA inputs in the wire harness.

NOTE: When using high-level signals, set the “Auto Turn-on” switch to “DC” (to turn on when it receives battery power) or “AUDIO” (to turn on when it senses audio signal). Set the input level to “HI1” in the settings menu (see “setting the input level”). If no sound plays, change the input level to “HI2”.

Connecting the remote bass control in the vehicle
Plug the remote bass controller into the appropriate input in the wire harness. Mount the remote in a convenient location, such as under the dash, using sheet metal screws. Turn the dial clockwise to increase the bass output, and counterclockwise to decrease the bass output.

NOTE: Remote bass control will only operate in subwoofer mode.

SETTING THE SOUND IN THE VEHICLE

In Settings Mode, you can adjust the input level, gain, low-pass crossover, phase control, and bass boost.

NOTE: To enter Full-Range Mode from Subwoofer Mode, press and hold the JBL Connect and Play/Pause buttons for 5 seconds. To switch back to Subwoofer Mode, repeat the same process.

Entering Settings Mode
Press and hold the JBL Connect button and the Bluetooth button for 5 seconds to enter Settings Mode. The power button will illuminate in yellow and an alert will sound. Press the JBL Connect button to toggle between settings. Press the “+” and “–” buttons to change the value of each setting.

The color of the first LED indicates which setting you are adjusting. The five white LEDs display the value of the adjustment.

Setting the input level
When the BassPro Go is docked in your vehicle, you will need to set the input level to accept the type of signal it receives from your source unit. Select level options by pressing the “+” and “–” buttons.

Setting the low-pass crossover in subwoofer mode
The crossover allows only frequencies below a certain point to reach the speaker in woofer mode. The crossover point you choose depends on your musical preferences.

Setting the gain
When the BassPro Go is docked in your vehicle, you will need to match the gain (input sensitivity) to output of the signal it receives from your source unit. To set the gain:

1. Start with gain control switch set to 2V.
2. Choose music with substantial bass content and turn the volume control on your receiver to 75% of its total output.
3. Increase the gain one step at a time by pressing the “+” button, listening carefully to the bass output, as the LED read out displays each step. To increase the interval of the gain you are adjusting, move the gain control switch to 2V, 4V, or 6V as necessary. If you hear distortion, lower the gain one step at a time by pressing the “–” button until the distortion disappears.

Setting the bass boost
You can apply a boost to the output at 45Hz in subwoofer mode and in full- range mode.

Setting the woofer phase
You can set the woofer phase to 0° or 180°, whichever provides the cleanest bass output.

Using the speaker in Full-Range Mode in vehicle
To enter Full-Range Mode, press and hold the Connect button and Play/Pause button simultaneously for 5 seconds. Repeat the process to return to Subwoofer Mode.

RELEASING THE SPEAKER FROM THE DOCK FOR PORTABLE USE

Follow these steps to remove the speaker from the dock

1. Pull the handle at the base of the dock forward.
2. Disconnect the wire harness by gently pressing down on the tab at the top of the plug, then pulling gently away
3. Lift away from the dock.

Replacing the back-panel cover
To ensure IPx5 water-resistant performance, replace the cover on the back panel by pressing it into place.

Connecting an audio device with Bluetooth
To enter pairing mode, press the Bluetooth button on the top panel. The button will flash to indicate that it is ready for pairing.

Find JBL BassPro Go on your audio device and select it. The Bluetooth button will remain illuminated when pairing is complete.

NOTE: Once you have paired a device, the BassPro Go will remember it and pair with it automatically. You can enjoy Social Mode and pair up to two more devices by pressing the Bluetooth button, then finding the BassPro Go in the menus of each Bluetooth device and tapping to pair. The BassPro Go will enter sleep mode after 10 minutes of inactivity, and power off after 20 minutes of inactivity. Press the power button to turn the speaker back on.

Adjusting playback volume and selecting play/pause when in portable use
To raise the volume when using the BassPro Go as a portable speaker, press the Volume Up (+) button. To lower it, press the Volume Down (–) button. To play or pause, press the Play/Pause button.

NOTE: You can also adjust the playback volume and play/pause using the controls on your Bluetooth music device.
NOTE: You can adjust the bass boost using the same steps described in the Settings Mode section above. Increased bass boost will shorten battery life.

Charging a music device with the BassPro Go undocked
The BassPro Go lets you charge your music device with its built-in USB port. To charge your device:

1. Remove the cover from the back panel.
2. Plug the USB power cable of your device into the USB port on the back panel of the BassPro Go.

Connecting to another JBL speaker using JBL Connect
You can link a second JBL BassPro Go, for simultaneous playback of two speakers. To link your devices:

1. Press the JBL Connect button. The power button will flash white.

2. The devices will automatically connect. When they are connected, the power button will turn blue.

NOTE: If the devices do not connect, the power button will return to solid white. Try the process again. BassPro Go is not compatible with JBL Connect+ or JBL Party Mode-enabled products.

Blue, solid

| Speaker is connected to a second speaker with JBL Connect

Monitoring battery level in portable mode
The LED readout will show you the level of the battery when in portable mode.

SPECIFICATIONS

• RMS Power Output in-vehicle, subwoofer mode: 100 watts (200 watts peak)
• RMS Power Output in-vehicle, full-range mode: 2×30 watts (tweeter) & 1×80 watts (woofer)
• RMS Power Output out-of-vehicle, full-range mode: 2×15 watts (tweeter) & 1×40 watts (woofer)
• Amplifier Class: Class D
• Battery Voltage Range (Volts) : 9V to 16V
• Quiescent current: <1.2A
• Selectable Turn-on Modes: 12V, Audio Signal Sense, DC Offset
• LED Indicator: multicolor
• Total Frequency Response: 40Hz to 20kHz @ -3dB
• Signal-to-Noise Ratio: >70dB (1W output at 4 ohms)
• THD+N @ 4-ohm: <1%
• Input Sensitivity, selectable: High-level or low-level
• Input Sensitivity – Low Level : 400mV to 6V
• Input Sensitivity – High Level: 1V to 15V
• Low-pass crossover: Selectable 80, 100, 120Hz @ 12dB slope
• Bass Boost : Selectable 0dB / 3dB / 6dB @ 45Hz
• Phase Control: Yes, selectable
• Gain: Selectable 0-15
• Fuse Rating: 15A
• Speaker Level Inputs: Yes (RCA adapter)
• Remote Bass Control: Included
• Bluetooth Version: 4.2
• Bluetooth Profile: A2DP 1.3, AVRCP 1.6
• Bluetooth Transmitter Frequency Range: 2.402GHz – 2.480GHz
• Bluetooth Maximum Transmitter Power: 0 – 9dBm
• Bluetooth Transmitter Modulation: GFSK, 8DPSK, π/4DQPSK
• Battery type: Ni-MH (32.4Wh)
• Battery charge time: <4 hours
• Music playing time: Up to 8 Hours (Varies by volume level and music content)
• USB Charging (Type A connector) : 5V / 2.1A
• Micro USB: For Service Only
• Length: 402.5mm (15-7/8″)
• Width: 208.4mm (8-3/16″)
• Height: 198.7mm (7-13/16″)
• Weight: 5.28kg (11.64lbs)
• Protection: DC, OVP, UVP, OCP, OTP

TROUBLESHOOTING

No audio and POWER INDICATOR is off

• No voltage at BATT+ and/or REM terminals, or bad or no ground connection. Check voltages at amplifier terminals with VOM.

No audio and PROTECT INDICATOR is on

• Check to see if the input voltage is less than 9V or greater than 16V on BATT+ connection and vehicle charging system. In-line fuse keeps breaking
• The wiring is connected incorrectly or there is a short circuit. Review installation precautions and procedures. Check wiring connections.

Distorted audio

• Gain is not set properly. Check and adjust settings. Speaker or source unit may be defective. Unwanted noise in the audio signal
• Radiated vehicle noise in the line-level input cables. Make sure power wire and signal wires are not near each other (run them down opposite sides of the vehicle). Music lacks dynamics or “punch”
• Use 0°/180° phase adjustment. Loudness or audio performance varies with Bluetooth
• Loudness and volume will vary between phones. If you feel that the product is not loud enough, check your phone settings to see if any adjustments can be made to improve audio performance, or try using a different audio source or Bluetooth streaming device to determine if performance improves. Audio play/pause, track forward or track back are slow to respond in Bluetooth mode
• This will vary by phone or Bluetooth streaming device. Try using a different Bluetooth streaming device to see if this improves. If the problem persists, cycle the power off and let the speaker rest for a few minutes before turning power on.

Audio track is cutoff in first few seconds when using track forward or track back

• This will vary by phone and the capability of the phone to communicate with Bluetooth control from an external device. Try using a different Bluetooth streaming device to see if this improves.

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by HARMAN International Industries, Incorporated is under license. Other trademarks and trade names are those of their respective owners.

HARMAN International Industries, Incorporated 8500 Balboa Boulevard, Northridge, CA 91329 USA https://www.jbl.com/

• 2020 HARMAN International Industries, Incorporated. All rights reserved. JBL is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. Features, specifications and appearance are subject to change without notice.

References

• Official JBL Store - Speakers, Headphones, and More!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>