Harbor Breeze 7404281304 LED Path Light Instruction Manual

ITEM #5488937
LED PATH LIGHT
MODEL #7404281304
AS23573

HARBOR BREEZE and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
Thank you for purchasing this HARBOR BREEZE product. We’ve created these easy- to-follow instructions to ensure you spend your time enjoying the product instead of putting it together. But, if you need more information than what is provided here, please visit Lowes.com , search the item number and refer to the Guides & Documents tab on the product’s page.

TROUBLESHOOTING

contact pins.
2. The wire and the power pack aren’t in contact.
3. No power to the power pack.| 1. Check the wiring of connector. Make sure brass contact pins pierce the plastic wire insulation and are touching the copper wires inside.
2. Check the connection between the primary wire and the power pack.
3. Check the power to the power pack.

CARE AND MAINTENANCE

• Before attempting to clean the fixture, disconnect the power to the fixture by unplugging the fixture.
• To clean the fixture, use a dry or slightly dampened clean cloth.
• DO NOT use any cleaners with chemicals, solvents or harsh abrasives as damage to the fixture may occur.
• Total fixture wattage is 3.4 watts; do not attempt to replace the LEDs.

SAFETY INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING

• Be sure the electricity to the wires you are working on are shut off by either removing the fuse or turning off the circuit breaker.
• To reduce the risk of fire, electric shock or injury to persons: do not touch hot lens, lampshade or enclosure.
• If you feel you do not have enough electrical wiring experience or are unsure what electrical codes are applicable to your jurisdiction, please consult the services of a qualified, licensed electrician.

CAUTION

• Keep lamp away from combustible materials that may burn.

• The wire is intended for shallow burial, less than 6 inches deep.

• DO NOT install fixure within 10 feet of a pool, spa or fountain.

• The LEDs in this product are not replaceable.

• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  This equipment has been tested and found to comply with the limits for a Class-B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  – Reorient or relocate the receiving antenna.
  – Increase the separation between the equipment and receiver.
  – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  – Consult the dealer or an experienced radio/TV technician for help.
  Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

• FCC responsible party: Lowe’s Home Centers LLC., 1000 Lowe’s Blvd. Mooresville, NC 28117./Tel: 888-251-1003.

PACKAGE CONTENTS

ASSEMBLY INSTRUCTIONS

• Attached the post(B) to the Lamp fixture(A) and the stake(C) to the post(B).

• Unscrew the top cover from the connector (D) and keep it for later use.

• Insert wire from low-voltage transformer (sold separately) into the bottom base of connector (D) and then re-tighten the top cover removed in step 3 until the contact pins completely pierce the plastic shield of the wire.

Note:
a: The brass pins must be aligned to the center of wires and tightened.
b. This fixture is a safety low-voltage (AC12V), and the brass pins can be exposed but pose no danger of electric shock.

• Push the assembled fixture into the ground until the rim of the stake is only visible. Do not use a hammer. Never push the fixture into the ground by the head. Instead, hold the post and push the fixture into the ground.

WARRANTY

The manufacturer warrants this lighting fixture against defects in materials and workmanship for a period of five year from the date of purchase. If within this period the product is found to be defective in material or workmanship, the product must be returned, with a copy of the bill of sale as proof of purchase, to the original place of purchase. The manufacturer will, at its option, repair, replace or refund the purchase price to the original purchaser consumer. This warranty does not cover light bulbs or the fixture becoming damaged due to misuse, accidental damage, improper handling and/or installation and excludes liability for direct, incidental or consequential damages. As some states do not allow exclusions or limitations on an implied warranty, the above exclusions and limitations may not apply. This warranty gives you specific rights and you may also have other rights that vary from state to state.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 10-15 minutes
No Tools Required for Assembly.
Printed in China

Questions, problems or missing parts?
Before returning, contact us on:
888-251-1003, 8 a.m. – 8 p.m.,
EST Monday – Sunday or ascs@lowes.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>