Harbor Breeze ZDL1194 LED Adjustable Beam Spot Light Reflector Instruction Manual

Harbor Breeze ZDL1194 LED Adjustable Beam Spot Light Reflector

Thank you

Thank you for purchasing this Harbor Breeze product. We’ve created these easy- to-follow instructions to ensure you spend your time enjoying the product instead of putting it together. But, if you need more information than what is provided here, please visit Lowes.com, search the item number and refer to the Guides & Documents tab on the product’s page.

TROUBLESHOOTING

1. The transformer is not plugged in or turned on.
2. Fixture connector is not properly installed on the low voltage cable.

|

1. Make sure the transformer is plugged in and turned on.
2. Make sure the contact pins pierce the wire insulation
   and make proper contact with the wire.

CARE AND MAINTENANCE

Clean the lens, lamp head and lamp stand regularly with a non-abrasive cleaner. Warning: Always make sure the light is unplugged and completely cool before attempting to clean it

WARRANTY

This fixture is warranted to be free from defects in materials and workmanship for five (5) years from the date of original purchase. Call 888-251 1003 to obtain a Return Authorization number and further instructions. The manufacturer will be liable for the replacement of the defective item and will not be liable for any other loss, damage, or injury which is caused by the product.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Assembly Time: 10 minutes
No tools required.

FEELING CONFIDENT

START YOUR NEXT PROJECT

Visit www.lowes.com for more information.

 SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

• Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
• For use with low-voltage landscape lighting systems only.
• The wire is intended for shallow burial, less than 6 in. deep.
• Install all luminaires 10 ft. or more from a pool, spa or foundation.
• Keep lamp away from material that may burn.
• Do not touch hot lens, guard or hot fixture housing.
• Do not operate or install a fixture with missing or damaged parts.
• Do not touch the LED at any time as this may cause damage to the fixture.

CAUTION

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

 SAFETY INFORMATION

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This product is not a toy and must not be operated by children.
• Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
• Do not submerge in water. The product can be damaged.
• Use with 18AWG minimum, underground low-voltage circuit cord.

PACKAGE CONTENTS
x 1

x 1

INSTALLATION OVERVIEW

For 16 AWG cable, insert the wire into the connector directly.

For 12-14 AWG landscape lighting cable, remove the wire adapter before inserting the wire into the connector. Then tighten it.

 Insert wire from low-voltage transformer (sold separately) into the wire guide by twisting the wire into each end of the wire guide. Align the pins on the connector top cover so that each pin lines up with opposite sides of the wire. Securely tighten the connector top cover making sure the pins completely pierce the plastic shield of the wire.

OPERATING INSTRUCTIONS

Push the button, select desired color temperature.

Choose your preferred beam angle: from min 30°-max 60°. Rotate the beam angle control knob clockwise or counter clockwise to adjust to your
desired beam angle.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>