Monoprice TWE-03 True Wireless Plus Touch Bluetooth Earbuds User Manual

: June 8, 2024
: Monoprice

Monoprice TWE-03 True Wireless Plus Touch Bluetooth
Earbuds

TWE-03

User Manual

Overview

EarBud

Monoprice Earbuds Secondery Mic, Touch Bar, LED, Acoustic Hole, Charging Contactor, Primary Mic

Remark: Please make sure that the eartips can not cover the acoustic hole, otherwise the bass will be influenced.

Charging Case

Charging Case Female USB Port, Pogo Pins, LED

How to Wear

Adjust primary Mic towards your mouth.

For maiden use, please follow up below steps:

1. The two side earbuds auto-power on and connect with each other upon opening the lid, and left side will then auto enter pairing model( with voice prompt) when LED blinks red & white, right LED turn off)
2. On cellphone,search for TWE3Plus_L and tap to connect earbud to cellphone;

Option one

3. Close the bluetooth of cellphone, and put both earbuds back to case and close the lid.
4. Open the lid again, and wait until left side enter pairing mode(LED blinks red and white), then take right side out and close the lid, the right side will enter pairing model when right LED blinks red and white.
5. On cellphone, open Bluetooth and search for TWE3Plus_R and tap to connect earbud to cellphone;
6. Two side earbuds have the connection records with cellphone now and you are good to go.

Option two

3. Disconnect the left earbud with cellphone, left side will enter pairing model again with red and white LED.
4. Take right earbud out of case and close the lid, right earbud will enter pairing model when right LED blinks red and white.
5. On cellphone, open Bluetooth and search for TWE3Plus_R and tap to connect earbud to cellphone;
6. Two side earbuds have the connection records with cellphone now and you are good to go.

Note: Please follow up these steps for the maiden use, it will be useful for future use if you want to experience master and slave switch funtion.

TWS Mode

Earphones will auto power on and connect with each other upon opening the lid.Left earbud will then auto enter pairing mode(with voice prompt) when right LED turns off and left LED blinks red and white. On cellphone, search for TWE3Plus_L and tap to connect earbud to cellphone.

(Please try the following steps if two earbuds fail to pair with each other)

TWS Mode

Power off earphones, touch both bars for 10s or until LED glows solid white then double touch both bars in 5s to set earphones to factory setting (then LED will blink white promptly). Two earbuds will auto connect with each other and left earbud will auto enter pairing mode (Left LED blinks red and white, right LED turn off). On cellphone, search for TWE3Plus_L to connect earbud to cellphone.

Note： two earbuds should pair with each other in 5 mins otherwise they will auto power off finally.

Mono Mode

Touch for 5s

Mono Mode

Option one
1. Power off earphones, then touch the bar on either earbud for 5s to enter pairing mode (LED will blink red and white)
2. On cellphone, search for TWE3Plus_R/L and tap to connect.
3. Pairing completed.

Option Two

1.Open the lid ,take right earbud or left earbud out of case and close the lid;
2. TWE3Plus_R/TWEPlus_L will auto connect to cellphone;

Note: For option two, two earbuds should have connected records with cellphone before, if not, please follow up the instruction of maiden use.

Stereo Mode

Power-on

Touch both bars for 1s in power off status Open the lid when both earbuds are charging (LED will glow solid white for 1s)

Power-off

Pick up both earbuds and touch both bars for 8s Pop both earbuds back into the case then close the lid (LED will glow solid for 2s)

Answer Call

Double touch the bar to answer incoming call and double touch again to end it

Volume Control

Volume Up: when playing, slip up on left touch bar
Volume down: when playing, slip down on left touch bar

Skip Track Forard/backward

When playing, slip up on right touch bar to skip track backward When playing, slip down on right touch bar to skip track forward
Note: mono mode do not have this function.

Voice Assistant

When standby or playing, triple touch the touch bar to activate/deactivate voice assistant

Factory Setting

Power off earphones, touch both bars for 10s or until LED glows solid white then double touch both bars in 5s to set earphones to factory(LED will blink white promptly).

Pause/Resume Playing
When playing, double touch the touch bar to pause music and double touch again to resume playing

Reconnecting

The earbuds will enter pairing model if disconnect with cellphone.
(LED will glow red and white promptly)

When two earbuds are charging in the case, open the lid and they will auto reconnect to the cellphone(two earbuds need to be connected before)

Note: earbuds will auto enter pairing mode, if they fail to reconnect in 5s

Charging the Earphones

Push earbuds back to case then close lid to power off and charge them. LED will glow solid red when charging and turn white for 8s once topped up.

Charging the Earphones

Charging the Case

Charge the case via USB cable. LED will blink green when charging and glow solid greeen once topped up.

Charging the Case
Features

Bluetooth v5.0 chipset transmits signals stably with low lag
Easy touch control
Crystal-clear stereo talking thanks to dual mic NC technology

Product Parameters

Model: TWE3Plus
Chipset: QCC3026
Bluetooth version: V5.0
Waterproof: IPX5
Bluetooth Codec: SBC, AAC and APTX
Standby time: approx. 150hr
Charging time: approx. 2hr
Music time: approx. 11hr
Talking time: approx. 6hr
Operation range: 10m (with no obstacle)
Battery type: li-ion
Battery capacity(earphones): 3.7V 60mAh
Battery capacity(charging case): 3.7V 600mAh
Input parameter(charging case): 5V 500mA
BT profiles: HSP/HFP/A2DP/AVRCP

(All technical data shall be subject to practical performance)

LED Indicators

The LED indicators give a good indication of what the earphones and charging case are doing.

Status Earbuds: LED Indicator

Power On : White indicator turns on and turns off after 1s
Power Off : Red indicator turns on and goes off after 2s
Earbuds Search for Each Other : White indicator flash promptly
Earbuds Successfully Connect to Each Other : Right indicator goes out, left indicator flashes in red and white
Pairing Mode : Red and white indicators falsh alternately
Charging : Red indicators stay on
Fully Charged : White indicators turn on and turns off after 8s

Status: Charging Case Indicator

Charge the Case
Start Charging : Both indicators flash green 3 times and go out
Battery Lever <30％ : Two indicator flashes green
30%<Battery Level <90% : One indicator stay on in green, the other flashes green
90%<Battery Level : Both indicators stay on in green

Status: Charging Case Indicator

No charge the case
Open or close the lid : Both indicators show the battery level for 5 s
Put the earphone back to charging case : Corresponding side indicator show 5 s in breathing status, and then display the battery level for 5 s and go off

Tips

1. Before using the headset, please read the manual carefully and keep it for future references.
2. The headset need to be fully charged prior to first-time use.
3. If the headset is left unused for over two weeks, please recharge it periodically.
4. Please use the chargers made by qualified manufacturer.
5. If the headset cannot be found by your phone, please check whether it is in pairing mode; if left unconnected for a long while, the headset will exit pairing mode, please re-enter the mode; if a procedure error of your phone occurs, reboot it; if a procedure error of the headsetoccurs, reboot or reset it.

Caveats

1. Never disassemble or modify your headset for any reasons to avoid any damages and danger .
2. Do not store the headset in extreme temperatures (under 0°C or over 45°C).
3. Avoid using the indicator close to the eyes of children or animals.
4. Do not use this headset during a thunderstorm to avoid irregular function and increased risk of electricshock.
5. Do not use harsh chemicals or strong deter gens to clean the headset.
6. Keep the headset dry.

Warranty Card

Warranty Period

12 months after you purchase this item.(or you may inquire your local shopper for more details.)

Free Service:
Supposing any defects caused by quality issues occur within the warranty period, please take this warranty card and purchase receipts to your distributor for free exchange service.

Model Number:
Date of Purchasing:
User’s Name:
User’s Phone:
User’s Address:
Shop’s Name:
Shop’s Address:
Comments:

Free exchange service will not be accessed under following circumstances：

1. Damages caused unauthorized disassembly.
2. Defects or physical damages caused by leaking or dropping off.
3. Damages by act of God. Supposing your item is within any damages or defects except the above circumstances, please return to us or your distributor for free repairing.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates use s and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication s. How ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver .
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not ca use harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

logo