QCY TWS Bluetooth Earbuds QCY-T5 User Manual

QCY-T5
TWS Bluetooth Earbuds

Official URL

Overview

Choose Your Eartips

L                              M                   S

Mic LED Touch barTuning Hole Pogo Pins

Please try medium eartips first as they fit most people.

How to Pair

First Time Pairing:

1. Pick up both earbuds.
2. On cellphone, search for QCY-T5 and tap to connect.
   *Once paired earbuds will auto power on upon picking up from the case. If earbuds fail to auto power on, please charge them and try again.

Switch Paired Device:

1. Turn off phoneA’s Bluetooth faculty and earbuds will auto disconnect and enter into pairing mode.
2. On phoneB, search for QCY-T5 and tap to connect.
   *Multi-point connection is not available. Earbuds will auto reconnect to phoneB upon powering up again.

Factory Setting

(Try the following steps to fix connectivity issue)
Set to factory:

1. On cellphone, search for QCY-T5, tap and choose ignore or cancel pairing.
2. Pick up two earbuds, keep touching both bars for 8s or until LEDs glow red for 2s to power off.
3. Keep touching both bars for 10s or until LEDs blink red and green 3 times then blink red to set earbuds to factory.
   *Please refer “First Time Pairing” to connect after factory setting.

How to Wear

1. Rotate earbud and pop it into your ear then shake head to check wearing stability.
2. Please adjust mic towards your mouth to gain better calling experience.

Three-way Calling & Switch
Earphones are connected with phoneA. Double press MFB to answer incoming call from phoneB. If another call is coming from phoneC in sync, double press MFB to put the first call on held while activating the second call.
Hold MFB to switch between active call and held call.

Ignore the second call in three-way calling: earphones are connected with phoneA. Double press MFB to answer incoming call from phoneB. If another call is coming from phoneC in sync, hold MFB to ignore the second call while keeping the first call.

Mono Mode

1. Power off earbud then keep touching the bar for 5s to enter pairing mode ( LED blinks red and green )
2. On cellphone, search for QCY_T5
3. Tap to connect

Charging Earbud
Push earbud into the case to charge. LED will glow solid red when charging and turn to green for 1 minute once top up.

Charging the Case
Charge the case via USB cable. LED will glow solid green when charging and turn off once top up.

Product Parameters
Model:In1925                              Pairing name: QCY-T5
Bluetooth version: V5.0               Stand time: approx. 70hr
Charging time: approx. 2hr          Music time: approx. 4 or 5hr
Talking time: approx. 4hr
Operation range: 10m(with no obstacle)
Battery type: li-ion
Battery capacity(earbud):3.7V 40mAh
Battery capacity(charging case):3.7V 380mAh
Input parameter(charging case):5V 500mA
Bluetooth profiles: HSP/HFP/A2DP/AVRCP

Function Introduction

Warranty Card

Warranty Period
12 months after you purchase this item.(or you may inquire your local shopper for more details.)
Free Service:
Supposing any defects caused by quality issues occur within the warranty period, please take this warranty card and purchase receipts to your distributor for free exchange service.

Model Number:
Date of Purchasing:
User’s Name:
User’s Phone:
User’s Address:
Shop’s Name:
Shop’s Address:
Comments:

Free exchange service will not be accessed under following circumstances:

1. Damages caused unauthorized disassembly.
2. Defects or physical damages caused by leaking or dropping off.
3. Damages by act of God.Supposing your item is within any damages or defects except the above circumstances, please return to us or your distributor for free repairing.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/11/ technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Hazardous substances and their contents in the item

This form is made by SJ/T 11364 regulation.

0: means that hazardous substance content in the homogeneous materials of this part is within the limits of (EU) 2015/863 regulation .
X : means that hazardous substance content in ,at least, one certain homogeneous material of this part is beyond the limits of (EU) 2015/863 regulation ,but there is no mature alternative in the industry at present, it still conforms to the EU ROHS Directive in the scope of exemption.

Notes: Please arrange using time properly as your hearing may be damaged by using the device for a long time.
Perform standard: Q/HL 1-2019 ; Q/HL 2-2017
Manufacturer: Dongguan Hele Electronics Co., Ltd.
Address: Daojiao Town, Dongguan City, Guangdong, China

Tips

1. Before using the headset, please read the manual carefully and keep it for future references.
2. The headset need to be fully charged prior to first-time use.
3. If the headset is left unused for over two weeks, please recharge it periodically.
4. Please use the chargers made by qualified manufacturer.
5. If the headset cannot be found by your phone, please check whether it is in pairing mode; if left unconnected for a long while, the headset will exit pairing mode, please re-enter the mode; if a procedure error of your phone occurs, reboot it; if a procedure error of the headsetoccurs, reboot or reset it.

Caveats

1. Never disassemble or modify your headset for any reasons to avoid any damages and danger.
2. Do not store the headset in extreme temperatures (under 0°C or over 45°C).
3. Avoid using the indicator close to the eyes of children or animals.
4. Do not use this headset during a thunderstorm to avoid irregular function and increased risk of electricshock.
5. Do not use harsh chemicals or strong detergents to clean the headset.
6. Keep the headset dry.

CMIIT ID: 2019DP6793

QCY TWS Bluetooth Earbuds QCY-T5 User Manual – Optimized PDF
QCY TWS Bluetooth Earbuds QCY-T5 User Manual – Original PDF

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>