Caseta Lutron Smart Bridge Wireless Quick Start Guide

: June 8, 2024
: Caseta

Table of Contents

Caséta® Wireless Quick Start Guide
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Caséta® Wireless Quick Start Guide

Lutron® Smart Bridge, Pico® remote controls & in-wall dimmers

Welcome —and thank you for purchasing a Caséta® Wireless dimming kit.

Before you install the dimmers, please watch the installation video at www.casetawireless.com/support

We hope you enjoy the convenience of Caséta® Wireless!

Double your warranty

Love Caséta® Wireless dimmers? Have ideas for making them better? Tell us what you think and we’ll extend your warranty by 1 year. www.casetawireless.com/register

Contents supplied

Tools you’ll need

Works with energy efficient dimmable light bulbs:

Works with energy efficient dimmable light bulbs

NOTE: You can mix and match dimmable LED, halogen, and incandescent light bulbs with Caséta® Wireless dimmers.

Dimmable LED light bulbs vary in their dimming performance. If you’re using these bulbs and they flicker or turn off, please visit 0301710 – low-end trim [Download] for information on adjusting the dimmer for best bulb performance.

For a complete list of compatible dimmable LEDs, please visit www.casetawireless.com/bulblist

Compatible light bulbs include:

Cree®
CR6-575L

EcoSmart®
ECS BR30 W27 FL 120
ECS 20 WW FL 50WE 120

Feit®
A19/OM/LED

Philips®
9290002295

Sylvania®
LED12A19/DIM/O/827
LED21PAR38/DIM/P/930/FL30

Installing your dimmers

Installation for lights with one wall switch (single-pole)

Turn power off at circuit breaker!

WARNING: SHOCK HAZARD.
May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.
Important note (3-Way) :
Some lights have one wall switch, while others have two or more wall switches (such as stair lights, which have a switch at both the top and bottom of the stairs). We’ve included instructions for lights with one wall switch (called a single-pole). If your light has more than one switch (called a 3-way), please visit 0301710a_caseta advanced inst [Download] ** for complete installation instructions and how-to videos.
**
Remove existing switch from wall
Remove the wallplate from switch.

Remove the switch and pull it away from the wall.

Disconnect all three wires* from the switch.

If your switch has more than 3 wires attached, see “Installing Caséta® Wireless in a 3-way switch application” video at 0301710a_caseta advanced inst [Download]
1. Remove side sections (if necessary)
  
  Do not remove outside side sections on dimmers at the end of gang.
  
  Important note:
  Removing side sections reduces the dimmer’s maximum wattage rating. See the chart below for maximum wattage information.
2. **Connect the dimmer

**

1. Connect the bare copper (or green) “ground” wire from the wallbox to the green wire on the dimmer using a wire connector.
2. Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.
3. Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.

Mount the dimmer
Use the screws provided.
Attach the wallplate
Attach the adapter to the dimmer using the screws provided and snap on the wallplate.

(If you installed the dimmer next to other dimmers or switches, you’ll need to install a wallplate with the correct size/number of openings to accommodate all the devices.)
Turn power on at circuit breaker

Repeat Steps 1 through 7 to install the second dimmer.

Using your Caséta® Wireless kit

Install the Lutron® Smart Bridge
A. Connect the Smart Bridge to your Wi-Fi router using the Ethernet cable.

B. Connect the power cord to the Smart Bridge and plug it into an outlet.
Download the Lutron® app and walk through setup

Apple is a trademark of Apple Inc., registered in the U.S. and other countries. HomeKit is a trademark of Apple Inc.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.

Using your controls

Using your controls 1

Using your controls 2

Connected to a Class 2, LPS, or SELV, limited energy (<15 W) power source only

Troubleshooting

Important notes:

For indoor use only
Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C)

Go to www.casetawireless.com/support for additional troubleshooting suggestions.

CAUTION

Use only with permanently installed fixtures with dimmable LED, halogen, or incandescent lamps. To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances.

Codes

Install in accordance with all national and local electrical codes.

Grounding

When no “grounding means” exist in wallbox, the National Electrical Code (NEC®) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove green wire before screwing control into wallbox.

Use of the HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.