Caseta 0301799 In-Wall switch User Guide
- June 3, 2024
- Caseta
Table of Contents
In-Wall switch
Welcome –and thank you for purchasing a Caséta Wireless in-wall switch.
In order to control your lights from an app or remote, you’ll need to replace
an existing switch with a Caséta Wireless in-wall switch.
We hope you enjoy the convenience of Caséta Wireless!
Double your warranty
Love Caséta Wireless products? Have ideas for making them better? Tell us what
you think and we’ll extend your warranty by 1 year.
http://www.casetawireless.com/register
Contents supplied
Tools you’ll need
Installing your switch
Installation for lights with one wall switch (single-pole)
Turn power off at circuit breaker!
WARNING: SHOCK HAZARD
May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.
Contractor note:
For wiring diagrams, please visit http://www.casetawireless.com/wiring
Important note:
Some lights have one wall switch, while others have two or more wall switches
(such as stair lights, which have a switch at both the top and bottom of the
stairs). We’ve included instructions for lights with one wall switch (called a
single pole). If your light has more than one switch (called a 3-way), please
visit http://www.casetawireless.com/3way for complete installation
instructions and how-to videos.
Remove existing switch from wall
Remove the wallplate from switch.
Remove the switch and pull it away from the wall.
Disconnect all three wires from the switch.
If your light
has more than one switch (called a 3-way), please visit
http://www.casetawireless.com/3way
Remove side sections (if necessary)
Do not remove outside side sections on switches at the end of gang.
Important note:
Removing side sections reduces the switch’s maximum wattage rating. See the
chart below for maximum load information.
Maximum load derating chart (120 V~ 50/60 Hz)
1 The in-wall switch is ULR Listed for use with all magnetic and electronic
fluorescent ballasts.
2 The maximum lamp wattage is determined by the efficiency of the transformer,
with 70%–85% as typical. For actual transformer efficiency, contact either the
fixture or transformer manufacturer. The total VA rating of the transformer(s)
shall not exceed the VA rating of the in-wall switch.
Connect the switch
1 Connect the bare copper (or green) “ground” wire from the wallbox to the
green wire on the switch using a wire connector.
2 Connect the load wire from the wallbox to the red wire on the switch using a
wire connector.
3 Connect the hot wire from the wallbox to the black wire on the switch using
a wire connector.
4 Connect the neutral wire from the wallbox to the white wire on the switch
(neutral connection required).
5 Cap the blue wire with a wire connector.*
- Note: The blue wire is only used in 3-way installations. See http://www.casetawireless.com/3way for more information.
Mount the switch
Use the screws provided.
Attach the wallplate
Attach the adapter to the switch using the screws provided and snap on the
wallplate.
(If you installed the switch next to other switches or dimmers, you’ll need to install a wallplate with the correct size/number of openings to accommodate all the devices.)
Turn power on at circuit breaker
CAUTION
Use only with permanently installed lighting loads or with general purpose fan
loads.
Codes
Install in accordance with all national and local electrical codes.
Grounding
When no “grounding means” exist in wallbox, the National Electrical Code
(NEC®) allows a control to be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic attachment screws or 2) the
circuit is protected by a ground fault circuit interrupter (GFCI). When
installing a control according to these methods, cap or remove green wire
before screwing control into wallbox.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment. Note: This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Using your Caséta Wireless kit
With a smartphone or tablet (Smart Bridge required, sold separately)
The Caséta Wireless switch can be controlled from a smartphone when used with
the Lutron Smart Bridge.
If you are using the switch and remote control with the Lutron Smart Bridge
follow the instructions below.
Download the Lutron app
http://www.casetawireless.com/LutronApp
Launch the Lutron app
Use the Lutron® app to complete ALL remaining steps
Without a smartphone or tablet (Smart Bridge not required)
Press and hold “off” button on the switch
Press and hold “off” button on remote
Repeat steps to pair other Pico remote controls.
Using your controls
Replacing light bulbs using FASS
Pull the FASS out on the in-wall switch to remove power at the light socket.
Important notes:
1. For indoor use only.
2. Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
Troubleshooting
Go to http://www.casetawireless.com/support for additional troubleshooting suggestions.
Device Ratings
In-wall switch
PD-6ANS
120 V~ 50/60 Hz
Lutron, the Lutron logo, Caséta, FASS, the Caséta logo, Smart Bridge, and Pico
are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the
US and/or other countries. Apple is a trademark of Apple Inc., registered in
the U.S. and other countries. App Store is a service mark of Apple Inc. All
other product names, logos, and brands are property of their respective
owners.
©2014–2021 Lutron Electronics Co., Inc
For advanced features, tips for using Caséta Wireless products with LEDs, the complete Caséta Wireless product line, and more, please visit http://www.casetawireless.com/features
References
- Installing Caséta for a light with two switches | Lutron
- Application Notes | Caséta Wireless | Lutron
- casetawireless.com/register
- Application Notes | Caséta Wireless | Lutron
- casetawireless.com/warranty
- Wiring Diagrams | Caséta Wireless | Lutron
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>