VEVOR FA200W Wind Turbine Generator Owner’s Manual

Technical Support and E-Warranty Certificate www.vevor.com/support

WIND TURBINE GENERATOR

MODEL: FA200W

We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.

WIND TURBINE
GENERATOR

MODEL:FA200W

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:

Technical Support and E-Warranty Certificate
www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

| Warning-To reduce the risk of injury, user must read instructions manual carefully.
---|---
| CORRECT DISPOSAL
This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices

1. Important Safety Instructions

READ THESE INSTRUCTIONS BEFORE ASSEMBLING, INSTALLING OR OPERATING YOUR PRODUCT.

1. SAVE THESE INSTRUCTIONS. This manual contains important instructions that must be followed during assembly, installation and maintenance.
2. Read, understand and respect all warnings.
3. Do not install wind turbine on a windy day.
4. If unusual noise or operation is experienced, turn off machine and contact authorized service personal.
5. During assembly and installation properly torque all fasteners.
6. Use only proper grounding techniques as established by the NEC.
7. Wind turbine codes. Failure to comply with manual and local codes may affect and possibly void your warranty.
8. Rotating blades are a serious mechanical hazard. Install wind turbine so no one can come into contact with blades.

FCC Information

CAUTION:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment!
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This product may cause harmful interference.
2. This product must accept any interference received, including interference that may cause undesired operation.

WARNING:
Changes or modifications to this product not expressly approved by the party. responsible for compliance could void the user’s authority to operate the product.

Note:
This product has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This product generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.
• Increase the distance between the product and receiver.
• Connect the product to an outlet on a circuit different from that to which the receiver is connected.

2. LA SERIES TECHNICAL SPECIFICATIONS

Type

| FA1.2-200
---|---
Rated Power (W)|

200

Rated Voltage (V)

| DC 12/24
Rotor Diameter (m)|

1.2

Star up Wind Speed (m/s)

| 2.5
Rated Wind Speed (m/s)|

12

Wind Blades Number

| 3/5
Shell Material|

die cast aluminum

Wind Blades Material

|

high strength nylon composite

1. wind blades
2. hub
3. nuts & bolts
4. flange
5. splicing sleeve
6. wind generator

3. WIND TURBINE ASSEMBLY PROCEDURES

• Wind turbine and tower connection: wind turbine sets on top of towers or poles, such as Figure 1:
  A special connection sleeve for the top of a tower or pole

Figure 1

3.1 Unpacking Check

According to the following table to check the box interior parts are complete, in order to ensure the normal assembly.

Item

| Description| Number
---|---|---
1| Wind Generator|

1

2

| Wind Blades| 3/5
3| Flange|

1

4

| Hub| 1
5| Bolts|

1

6

| Casing| 1
7| Install Manual|

1

3.2 Wind Turbine Generator Install Steps

1. The tower will be tilted (inclined angle to facilitate the installation of wind turbines is appropriate); the two cables from the bottom of the tower through the top hole out; and the wind turbine two lead connection, wrapped with insulating tape Well, put the cable into the tower (as Figure 2 shows).
2. Install the wind turbine brackets into the tower bushings and align them with four holes, with four M8*20 hex screws plus a Ø8 flat pad(see Figure 3 / Figure 4) (Note: fan leads With 4mm²cable)

Figure2                                           Figure3

Figure4                                          Figure5

3. wind blades is mounted2on the flange, pay attention to the word with a face outward (as shown in Figure 6), with M6*20 (3) Hexagon screw and M6 self- locking nut will be connected to the flange, self-locking nut fixed in the flange groove with a 5mm hex wrench locking tightly (shown in Figure 7), in this way, the other two wind blades fixed on the flange, adjust the distance between the two tips within 5.0mm and then tighten the bolts to ensure that the wind turbine balance (as shown in Figure 8)

Note: Literal face outward.

Figure6

Figure7

Figure8

1. fan center line
2. blade
3. bolts and nuts
4. flange

4. Remove the M16 nut from the wind turbine generator (made finish in step 3) and connect on the rotor shaft of wind turbine generator, and then install the nut in the groove of the flange, with the 8mm hex wrench into the hexagonal hole in the middle of the rotor shaft and turn the rotor shaft counter clockwise to Lock it, at least 3 teeth out; (as shown in Figure 9)
5. Install the hub, buckle the hub on the flange, shake the hood to ensure it completely buckle in the flange to avoid high-speed operation in case the hub get off; (Figure 10)

Figure 9                                     Figure10

6. Tower installation fixed, when install tower, please ensure that the tower is perpendicular to the horizontal plane, deviation should be 0.5 degrees or less;
7. Charge controller installation:
   charge controller connected to the battery first, the battery connection terminal “+” “-” connect to the charge controller “+” “-“o n the right.
8. Connect the wire line. The output of the wind turbine is three-phase AC, and the three terminals of the three lead wires are connected to the controller without distinguishing between the positive and negative terminals (show. Note: the controller is connected to the battery before connecting the wind turbine).

4. MAINTENANCE

• Although your wind turbine has been designed to run for long periods without requiring any maintenance, reliability and performance will be enhanced if you periodically inspect your system.
• After blades for chips or nicks. Replace blades if damaged. Do not operate the turbine with chipped or unbalanced blades. This can cause severe wear, damage, and possible failure. Do not install individual blades. The blades are balanced as sets.
• Check the blade bolts and the hub but for tightness.
• Check nosecone for cracks and proper fit.
• Wash off any built-up dirt or debris from the blades.
• Check all electrical connections to make sure they are tight and free from corrosion.
• As with all charging systems, check your battery water levels and add distilled water in accordance with manufacture’s recommendation.
• We suggest replacing the blades and bearing every five years for optimal performance.

CAUTION: Never approach the turbine during operation.

5. TROUBLE CLEARING

The power generation system design is extremely demanding, under normal installation and use do not usually fail. Under special circumstances, please refer to the following table:

Fan vibration| Failure Causes|

1. Rope loose 
2. Fixed blade bolts loose
3. Wind turbine blades by external defect 
4. Imbalance caused by blade attachments

---|---|---
Exclusion Method|

1. Adjust the tension rope 
2. Tighten loose part
3. Replace blades
4. Clear attachments

Abnormal murmur| Failure Causes|

1. Loose fasteners
2. Alternator bearing damage 
3. Wind wheel and other parts of the friction

Exclusion Method|

1. Tipped fan bracket, check all parts 
2. Replace bearings 
3. Examination to exclude

Significantly reduced rotor speed| Failure Causes|

1. Generator stator and rotor friction 
2. Stator winding short circuit or output short circuit 
3. Switch is in the down position controller

Exclusion Method|

1. Replace bearing 
2. Short positions will be insulated
3. Power switch set to the position controller

Generator output voltage is low| Failure Causes|

1. Motor speed low 
2. Three-phase short circuit in stator winding 
3. Controller circuit 
4. Low-voltage transmission line is too long or too small

Exclusion Method|

1. Identify the reasons for return to positive production speed 
2. Short positions will be insulated
3. Replace controller
4. Shorten lines, bold diameter

No output generator AC line| Failure Causes|

1. Output line circuit

Exclusion Method|

1. Identify the reasons, turn circuit

Motor AC output normal
But no DC output| Failure Causes|

1. DC blown fuse
2. Output line circuit 
3. Controller rectifier damage

Exclusion Method|

1. Replace the fuse 
2. Identify the reasons, turn circuit

Battery output capacity is insufficient| Failure Causes|

1. Generator output voltage is too low 
2. Poor conductivity battery posts 
3. Battery failure

Exclusion Method|

1. Excluded by the above examinations 
2. Maintenance batteries

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD.
1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd.
Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

YH CONSULTING LIMITED.
C/O YH Consulting Limited Office 147,
Centurion House, London Road,
Staines-upon-Thames, Surrey, TW18 4AX

E-CrossStu GmbH
Mainzer Landstr.69,
60329 Frankfurt am Main.

Technical Support and E-Warranty Certificate
www.vevor.com/support

Documents / Resources

| VEVOR FA200W Wind Turbine Generator [pdf] Owner's Manual
FA200W Wind Turbine Generator, FA200W, Wind Turbine Generator, Turbine Generator, Generator
---|---

References

• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>