nedis Hot water dispenser hot water Instruction Manual

nedis Hot water dispenser hot water Instruction Manual

Hot Water Dispenser

For more information see the extended manual online: ned.is/kawd300fbk

Intended use
The Nedis KAWD300FBK is a hot water dispenser for instant boiling water. The product is intended for indoor use only. The product is not intended for professional use. Any modification of the product may have consequences for safety, warranty and proper functioning. This product is intended for use in environments for typical housekeeping functions that may also be used by non- expert users for typical housekeeping functions, such as: shops, offices other similar working environments, farm houses, by clients in hotels, motels and other residential type environments and/or in bed and breakfast type environments. This product can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the product in a safe way and understand the hazards involved. Children shall not play with the product. Cleaning and user maintenance shall not be done by children without supervision.

Specifications

Main parts (image A)

1. Reset hole
2. LCD display
3. Spout
4. Drip plate
5. Drip tray
6. Top lid
7. Water tank
8. Water level indicator
9. Power cable
10. Drainage stopper
11. Bottom cover
12. Reset key
13. Filter (optional)
14. Filter box
15. Temperature indicator
16. Volume indicator
17. Water temperature for milk
18. Setting the temperature manually
19. Touchscreen control lock
20. Descale indicator
21. Lack of water indicator
22. Water temperature for coffee or tea
23. Custom dispense volume
24. On /off button
    

Safety Instructions

WARNING

• Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep this document for future reference.
• Only use the product as described in this document.
• Do not use the product if a part is damaged or defective. Replace a damaged or defective product immediately.
• Do not drop the product and avoid bumping.
• This product may only be serviced by a qualified technician for maintenance to reduce the risk of electric shock.
• Unplug the product from the power source and other equipment if problems occur.
• Do not use the product to heat anything other than water.
• Do not use the product if the surface is cracked.
• Place the product on a stable and flat surface.
• Ensure no water enters the power outlet.
• Connect to a grounded outlet only.
• Do not unplug the charger by pulling on the cable. Always grasp the plug and pull.
• Do not let the power cable touch hot surfaces.
• Do not expose the product to direct sunlight, naked flames or heat.
• Never immerse the product in water or place it in a dishwasher.
• Do not remove the top lid while the brewing cycle is in progress.
• Unplug the product when not in use and before cleaning. · Unplug the product from the power source before service and when replacing parts.
• Children of less than 8 years should be kept away unless continuously supervised.
• Usage by children should be supervised at all times.
• This product is not a toy. Never allow children or pets to play with this product.
• Do not move the product during operation.
• The temperature of accessible surfaces may be high when the product is operating.
• Do not touch the hot parts of the product directly. · Do not fill the water tank below the “min” indicator. · Do not fill the water tank above the “max” indicator.

Before first use

1. Clean the product with a damp cloth.
2. Place the product on a stable and flat surface.
3. Connect the power cable A9 to a power outlet.

When you first use this product, perform two full cycles to clean the inside of the product.

Filling the water tank

1. Remove the top lid A6 from the water tank A7.

2. Fill A7 to the “max” on the water level indicator A8.
   Do not fill the water tank above the “max” on A8.
   Do not fill the water tank below the “min” on A8.
   Do not spill any water on the product.

3. Place A6 back on A7.

Tapping hot water

Do not remove A6 while hot water is dispensed.

1. Place a glass under the spout A3.
2. Select the preferred temperature and volume settings.
3. Tap the on / off button A24. Hot water flows from A3 until the set volume has been dispensed.
4. Press A24 to manually stop the cycle.

Emptying the drip plate

1. Place one hand on A6 to stabilize the product.
2. Lift up the drip tray A5 with the other hand.
3. Remove the drip plate A4.
4. Empty A5.
5. Place A4 back on A5.
6. Place A5 back on the product.

Touchscreen controls

Temperature indicator

A15

| Displays the current and the set temperature.

When the display shows “000”, unheated water is dispensed.

---|---
Volume indicator A16| Displays the current and the set volume.

When the display shows “000”, the water flows continuously until A24 **** is pressed.

Water temperature for milk A17| Dispense water at 40 °C. This temperature is especially suited for powdered milk.
Setting the temperature manually A18| Tap A18 ** to set the desired temperature between 45 and 100 °C and 000.
Touchscreen control lock A19**| After 10 seconds the LCD display will be automatically locked.

–    Tap and hold A19  for 3 – 5 seconds to unlock the product.

–    Tap A19  once to lock the product.

Descale indicator A20| Descale the product as soon as possible when

Aa lights up.

Lack of water indicator A21| Fill A7 if A21 lights up
Water temperature for coffee or tea A22| Dispense water at 92 °C. This temperature is especially suited for tea or instant coffee.
Custom dispense volume A23| Tap A23 to set the desired volume between 100 and 400 ml and 000.
On / off button A24| Tap A24 to start or stop the function setting.

Replacing the filter

1. Remove A6.
2. Take out the filter box A14 including the filter A13.
3. Clean the new A13 you want to use Immerse the filter vertically for 15 minutes. Rinse the filter under water for 15-20 seconds.
4. Place the new A13 into A14.
5. Place A14 into A7 on the original filter place of the product.

Recalibrating the volume and temperature

1. Place a water container underneath A3.

2. Tap and hold A18 for 3 seconds.
   A15 shows “AUT”
   A16 shows “000”

3. Tap A24.
   The machine recalibrates the volume and temperature. During the process water is dispensed through A3. After 4-5 minutes the machine automatically exits the calibration mode.

Resetting the product

– Place the reset key A12 into the reset hole A1.
The machine automatically exits the reset mode.

Descaling the product

1. Remove A6.
2. 2. Fill A7 with 1000 ml of white vinegar.
3. Add water to the max.
4. Place A6 back on A7.
5. Tap and hold Af for 3 seconds.
6. Remove A6.
7. Fill A7 with clean water to the max.
8. Place 6 back on A7.
9. Tap and hold A23 for 3 seconds.
10. Repeat step 6 – 9 until the odor of vinegar has been flushed away.

Display Error Codes

E0| PC board problem|

1. Unplug the product from the power source.
2. Contact a qualified technician for service/ repair.

---|---|---
E4 or E5| Temperature sensor or water inlet problem|

1. Unplug the product from the power source.
2. Contact a qualified technician for service/ repair.

E7| Lack of water| Fill A 7.

References

• Hot Water Dispenser | 2.7 L | Digital | Nedis

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>