Frymaster FPRE80 Rear Oil Dispose Kit Instructions

: September 26, 2024
: FRYMASTER

Table of Contents

Frymaster FPRE80 Rear Oil Dispose Kit
Product Usage Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Frymaster FPRE80 Rear Oil Dispose Kit

Specifications

Brand: Frymaster
Model: RE80 Rear Oil Dispose Kit
Part Number: 8263807

Product Usage Instructions

Installation Steps:

Disconnect power from the electrical power supply.
Remove the fryer from the hood to gain access to the rear of the fryer.
Remove filter pan and filter pan lid.
Remove the upper back from the fryer to ease assembly.
Ensure all dispose assembly hoses and fittings are tight before inserting assembly into the fryer.
Install dispose assembly to the left of the filter motor.
Check for proper alignment of dispose assembly bracket holes with filter pump motor bridge holes; rotate if needed.
Insert dispose assembly into the fryer on the far-left cabinet.
Securely attach assembly using bolts and nuts.
Place clevis hook over dispose valve assembly handle and secure handle assembly rod.
Align and attach front handle assembly to the front cross brace.
Align waste dispose port on the rear fryer brace, mark, drill pilot holes, and attach rear dispose port.
Remove plugged ports on the rear manifold and attach adaptor and flexline.
Attach wires from the harness to the rear switch on the dispose assembly.

FAQ

Q: What models are affected by this rear oil dispose kit?
A: This kit is designed for FPRE80 Fryers.
Q: How should I ensure proper alignment during installation?
A: Check that the dispose assembly bracket holes match up with the holes in the filter pump motor bridge. Rotate if needed.
Q: What should I do if the holes do not align during installation?
A: If the holes do not align, rotate the filter pump moto bridge 180 degrees as shown in Figure 1.

318-865-1711

800-551-8633
WWW.FRYMASTER.COM
EMAIL: FRYSERVICE@WELBILT.COM

Subject: 8263807 RE80 Rear Oil Dispose Kit Instructions
Models affected : FPRE80 Fryers

In This Kit

Part #| Description| Qty
1087455| HANDLE, FQ1814G BULK WASTE| 1
130000871| PLUMBING ASSY, REAR DISPOSE FQE| 1
1064182| HARNESS, OIL RETURN JUMPER 28″ W/ 3/16”| 1
8090412| SCREW, #10-1/2| 6
8090417| NUT, FLNG 1/4-20 SERR| 4
8090237| 4-40 KEPS| 4
8090131| BOLT, 1/4-20 X 3/4 HX| 4
1089575| HARNESS ASSY, OIL RTN JUMPER FPRE80| 1
8158000| LOCTITE 567 TUBE 6ML| 1
8101668| ADAPTER, MALE 5/8″O.D. X 1/2″| 1
8198045| RE80 REAR DISPOSE INSTRUCTIONS| 1

Instruction Sheet
Follow these instructions to install a rear dispose kit in the RE80 fryers.

Disconnect power from the electrical power supply.
Remove the fryer from the hood to gain access to the rear of the fryer.
3. Remove filter pan.
Remove filter pan lid.
Remove the upper back from the fryer to ease assembly.
Ensure all dispose assembly hoses and fittings are tight before inserting assembly into the fryer.
The dispose assembly will be installed to the left of the filter motor. Check to see that the dispose assembly bracket holes match up with the holes in the filter pump motor bridge, if not, the bridge will need to be rotated 180 degrees (see Figure 1).
Remove the plate from the bottom of the dispose assembly.
Insert the dispose assembly into the fryer on the far-left cabinet as shown (see Figure 2).
Line up the three (3) holes in the assembly with the holes on the filter motor bridge.
Insert a ¼” 20×5/8 bolt from the bottom into the assembly (see Figure 3 Figures 3 & 4) and attach with a nut on the top side. Insert the other two (2) bolts and attach nuts. Ensure all three bolts/nuts are securely fastened.
Place the clevis hook over the dispose valve assembly handle. Insert the handle assembly rod through the clevis clip, through the handle into the dispose assembly. Rotate the clip over the rod and snap into place as shown (see Figure 5).
Align the front handle assembly so the rod is aligned directly parallel to the contactor box. Attach the handle assembly to the front cross brace using existing holes and secure with 8090412 5/16” cabinet screws (see Figure 6). Pull the handle completely forward away from the fryer and push back towards the fryer. Ensure the handle moves freely.
Align the waste dispose port on the rear fryer brace, mark and drill two 1/8” pilot holes to attach the rear dispose port (see Figure 7).
Attach with 8090412 5/16” cabinet screws (see Figure 8).
There are two Figure 9 plugged ports on the left side of the rear manifold as viewed from the front of the fryer. Remove the right plug using a 3/8” drive wrench (see Figure 9).
. Attach the 8101668 adaptor to the open port in the oil manifold, from the previous step, using Loctite® (see Figure 10).
Attach the flexline from the dispose assembly to the fitting in the previous step (see Figure 11).
Attach the orange and blue wires from one end of the harness to the rear switch on the dispose assembly. Ensure the wires are attached to the two rear terminals on the switch as shown (see Figure 12).
Remove the two (2) nuts attaching the return switch cover under the second (2nd) vat. The switch is located under the rear side of the vat attached to the return valve (see Figure 13).
Disconnect the existing harnesses attached to the switch (see Figures 14 & 15). DO NOT REMOVE the unused insulated connector from the switch.
Remove the blue and orange wires from the switch. Attach the pigtail from the new harness from the dispose assembly to pigtail on the old harnesses (blue wires to blue wires and orange wires to orange wires) (see Figure 16).
Reattach the pigtails to the two (2) terminals on the switch (see Figure 17).
Reattach the switch cover removed in step 20.
Test the dispose kit by connecting the fryer to power. Pull on the dispose handle to ensure the switch activates the pump motor.
Reverse steps 2-5 to reassemble and return to operation.