dormakaba Assist 360 Adaptable Low Energy Drive System Instructions
- June 7, 2024
- dormakaba
Table of Contents
dormakaba Assist 360 Adaptable Low Energy Drive System
Product Information
Specifications
- Voltage Requirements: Line Breaker 10 Amps
- Frequency: 50/60 Hz
- Max Door Width and Height: The Maximum Enclosure Size allowable by ANSI 156.27 is 17′-0. When you add the diameter and the door opening height together, it shall be 17′-0 or less
- Certifications: Designed to comply with ANSI/BHMA A156.27-2019. The drive system must be commissioned based on door size, door weight, and prevailing conditions at the opening to ensure compliance
- Requires a 20 Amp circuit at 110 VAC-120 VAC
- Requires a 15 Amp circuit at 220VAC -230VAC
Product Usage Instructions
Traditional Operation Modes
In manual mode, push the door wing through the rotation. In power assist
mode, manually set the door in motion, and the drive system will partially
rotate the door for egress.
Touch-Free Operation
In Low Energy Automatic mode, the drive system rotates at low energy speed
for touch-free operation. Activate the drive system using touchless wave plate
actuators or set the door for continuous rotation.
FAQ
-
Q: What are the voltage requirements for the Motion Assist 360 Drive System?
A: The voltage requirements are Line Breaker 10 Amps with a frequency of 50/60 Hz. -
Q: How do I activate the low-energy drive system in touch-free mode?
A: You can activate the drive system using touchless wave plate actuators or set the door for continuous rotation. -
Q: What certifications does the product hold?
A: The product is designed to comply with ANSI/BHMA A156.27-2019 standards. -
Q: What is the maximum allowable size for the door enclosure?
A: The Maximum Enclosure Size allowable by ANSI 156.27 is 17′-0 when you add the diameter and the door opening height together.
For further assistance, contact dormakaba USA Inc. at 800 523 8483.
A Continuous Advantage
- Crane revolving doors set the standard for timeless design aesthetics. The introduction of our Crane Motion Assist 360 allows building ownersto realize touch free entrance into their buildings, making it easier and safer for pedestrians to use manual revolving doors. This new, lowenergy, state-of-the-art drive system provides an intuitive experience while preserving the architectural vision for the building.
- Classified as a manual revolving door, Crane Motion Assist 360 offers three (3) different modes of operation, allowing you to choose the best operation method for your building. Depending on the traffic flow of your building, a simple turn of the key can change the operation mode from
- Manual to Power Assist or to Low Energy Automatic – providing the industry’s first touch-free manual revolving door experience.
Two Traditional Operation Modes
In manual mode, the door functions as a traditional manual revolving door with the user pushing the door wing through the rotation. In power assist mode, the drive system is initiated after the door is manually set in motion and partially rotates the door to allow egress and return the door to the home (X) position.
Touch Free Operation
- When used in Low Energy Automatic mode, the energy efficient drive system rotates at low energy speed, allowing a user to pass through the door without physical contact. There are two (2) different options for activating the low-energy drive system.
- Touchless wave plate actuators can be used to start the drive system
- The door can be set for continuous rotation
- Motion Assist 360 delivers an unsurpassed user experience in a singular solution.
Installation
- Overhead with Floor Mounted Speed Control (Requires a 4” canopy fascia height)
- Overhead Mounted Motion Assist 360 drive and Speed Control (Requires a 8” canopy fascia height)
- In Ground (Requires 32” diameter by 10-3/4” depth floor pit) Remotely mounted power supply and controller (Up to 100’ away).
Available Crane Models
- 2000 Semi-Custom
- 3000 Fully Custom (Fully Formed and Welded)
- 4000 All Glass
- Available as a retrofit to existing Crane revolving doors
- Available in a rehab kit for other manufacturers’ revolving doors
Technical Features
- Voltage Requirements 100 –240 VAC, single phase * or 220VAC -230VAC +/-10% **
- Line Breaker 10 Amps
- Frequency 50/60 Hz
- Max Door Width and Height The Maximum Enclosure Size allowable by ANSI 156.27 is 17’-0”. When you add the diameter and the door opening height together, it shall be 17’-0” or less
- Certifications Designed to comply with ANSI/BHMA A156.27-2019. The drive system must be commissioned based on door size, door weight and prevailing conditions at the opening to ensure compliance
Requires a 20 Amp circuit at 110 VAC-120 VAC
Requires a 15 Amp circuit at 220VAC -230VAC
Any questions? We would be happy to assist.
Contact us at 800 523 8483
dormakaba USA Inc. | 6161 E. 75th St. Indianapolis, IN 46250 | dormakaba.us
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>