esp Colour Video Door Entry System User Manual

June 7, 2024
ESP

APKIT Manual.qxp_Layout 1 28/01/2016 11:46 Page 1

aperta logo

APKIT | COLOUR VIDEO DOOR ENTRY SYSTEM

esp Colour Video Door Entry System 1

USER MANUAL

esp logo

www.espuk.com

Page 2

System Cabling

All system cabling (excluding mains 240vAC supply) has been tested with Cat5E UTP PVC cable.

ELAND CABLES

Part Number – ASNFORCESEUTP
Find this product online:
elandcables.com | Cables & Accessories | LAN Cable | Cat 5E UTP PVC Cable

Page 3

System Components

Door Station 1  Monitor 1  System Power Supply
1

APDSSW        APMONW           APPOWSWDR
Door Station     Monitor              System Power Supply

Optional Accessories

Lock Power Supply 1                          EV-EXIT Push to release
1

EVBPSBB                              EV-EXIT
Lock Power Supply                Push To Release

                            Elctro-magnetic Lock 1

EV-EBG                                EV-ML-250/500XT
Emergency Release                Electro-magnetic Lock

Elctric Lock 1

ENTERD
Electric Lock

Page 4

Installation

Door Station 1

Site the door station a recommended 1.5 meters from the ground, or to suit application.

Fix device according the sunlight 1

The camera needs to point in the direction of where a visitor will stand during operation.

Fix device according the sunlight 2

Avoid areas of high sunlight and noise levels.

Installation angle 1

Surface mount the sunshield of the door station and connect the system cabling. Mount the camera to the sunshield by fixing with the supplied hex screw.

Monitor 1

Site the indoor monitor to suit application.MonitorMonitor, Monitor Mounting Bracket, 1-Gang Mount Box (if required, not supplied)

Surface mount the bracket of the monitor or if required onto a 1-gang mount box (not supplied).
Make the system connections to the back of the monitor and then slide the monitor onto the bracket using the hooks to hold firmly in place.

Page 5

System Connections Example 1

System Connection Example 1

Dip switch 6 set to ON when device is at the end of system line.
Dip switch 7 set to OFF to select monitor as the ‘Master’
Only one monitor on the system can be the ‘Master’

Ensure the Address ID switches are both set to OFF

Total cable run should not exceed 150 meters between door station and monitor

Power supply to be with-in 100 meters of monitor

No cable or connection polarity

Page 6

System Connections Example 2

The system power supply can support up to 5 devices

Total cable run should not exceed 150 meters between door station and monitor

Power supply to be with-in 100 meters of monitor

No cable or connection polarity

1. Only one monitor is set as the MASTER:
MASTER=

2. All other monitors set as SLAVE:
SLAVE= SLAVE

3. Last monitor on system line has dip switch 6 set to ON
END OF LINE= END OF LINE

4. When using different style monitors on the same system, please refer to supplied instruction to configure Master, Slave and End of line position.

System Connection Example A

A The dipswitches are accessable on the rear of the door station

B When using multiple door stations ensure that each unit has a seperate Address ID

Page 7

Lock Connections Example 1

Lock Connection Example 1Electro-magnetic lock | Electronic lock, Lock -release time, N.C for Electra-magnetic lock

Page 8

Lock Connections Example 2

  • The jumpers on the rear of the door station offer different types of release modes for alternative applications dependent on the jumper link settings. LOCK1 options;

Door Station 1          N.O Volt-free

Image of jumper link    N.C Volt-free

 N.O MAX

  • The door station has a secondary switch. LOCK2 options;

Door Station 1          N.O Volt-free

Image of jumper link    N.C Volt-free

 N.O MAX

  • Jumper 1 gives the option to set the release time;

5 Sec. Jumper  3 Sec. Jumper

  • Please refer to the operation guide for release instructions

Page 9

User Guide

Door Station 2 - user guideCall Button

Preview

Preview
Press once to view door station image

Lock

Lock Sign
Press once to release lock

Gate

Gate Sign
Press once to release lock 2

Talk

Talk Sign
Press once to talk to visitor

Monitor 2 - user guide

A Chime Volume: Slide switch for High, Medium and Low setting
B Chime Selection: Press button to select chime melody
C Monitor Brightness: Adjustment for brightness levels
D Monitor Chroma: Adjustment for the intensity of colour
E Talking Volume: Adjust the volume level of the monitor

A.  Door Station 3 - user guide The visitor presses the call button
B. A chime will sound
C. Monitor 1 The visitor’s image will appear on the monitor
D. Talk Sign Press the ‘Talk’ button and begin conversation
E. Then choose between the 3 options below

1. Talk Sign Press the ‘Talk’ button to end call
2. Lock Sign Press the ‘Lock’ button to release lock and press ‘Talk’ to end call
3. Gate Sign Press the ‘Gate’ button to release lock 2 and press ‘Talk’ to end call

Page 10

Installer’s Guide

Master / Slave Setting

When using multiple monitors on 1 system;
Only the 1 handset set as the MASTER will display an image when the door station is activated.
All other monitors will ring, and will display the image once the ‘Talk’ button is pressed.

In the event of no video or audio signals coming from the monitor, or if the call button or audio cannot be activated on the door station, check the following;

A That the system is powered sufficiently.
B Each monitor needs to be set to a MASTER or SLAVE position
C All system cabling is secured and properly connected.
D All system cabling is clear of breaks or short circuits.
E Bench test the system if the issue cannot be found.

In the event of a lock release issue, check the following;

A The user instructions and operation of the monitor has been understood.
B That the lock is powered sufficiently.
C All system cabling is secured and properly connected.
D All system cabling is clear of breaks or short circuits.
E On the rear of the door station, ensure the lock output is switching when activated by the monitor.

Page 11

Page 12

Elite Security Products Telephone: 01527 51 51 50
Unit 7, Target Park, Shawbank Rd        Fax: 01527 51 51 43
Lakeside, Redditch B98 8YN                email: info@espuk.com

E&OE – Errors and omissions excepted.D17

esp logo

www.espuk.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals