POOLCANDY Splash runner Motorized Luxury Pool Lounger Instruction Manual
- June 7, 2024
- POOLCANDY
Table of Contents
SPLASHRUNNER
MOTORIZED LUXURY POOL LOUNGER
INSTRUCTION MANUAL
Congratulations on your purchase of the Splash Runner® Motorized Pool Lounger
from PoolCandy. You and your friends will enjoy hours of outdoor fun with this
innovative product. Your Splash Runner features two propellers that enable you
to drive and turn in all directions!
The Splash Runner is easy to use, but be sure to use it safely. Before
starting, please read this manual thoroughly, especially noting the safety and
care. Keep this manual for reference. Your Splash Runner requires some
assembly. This package includes one pool lounger. For each side of the pool
lounger, it includes a battery case, a battery cover and handle, a control arm
sleeve, and a motor assembly that encloses the propeller. Your Splash Runner
also includes a repair kit, and this instruction manual.
For easy to follow video instructions, go to www.poolcandy.net/pages/support and click on Support or scan the QR code below:
http://www.poolcandy.net/pages/support
INFLATION
Your Splash Runner has three separate air chambers to inflate. The nozzles for
the air chambers are located on the underside of the backrest, behind the
headrest, and at the bottom of the lounger near the feet. The Splash Runner
can be inflated by mouth, with a foot pump, or with an electric pump.
To inflate, the Splash Runner with an electric pump, insert the pump nozzle
into the air valve. The valves include a flap to prevent air from flowing back
out of the chamber, so make sure to push the pump nozzle past the flap, to
ensure that air flows freely. Be careful not to over-inflate.
Be sure to securely close each valve cover after completing each section.
ASSEMBLY
Once the lounger has been inflated, repeat the following steps on both sides of your Motorized Pool Lounger. Be sure to assemble it on a raised surface to prevent the motor assembly from being damaged.
Step 1.
Insert the control arm sleeves into the openings in the armrest on the
inflatable. Be sure to push the sleeve in until the top area is level with the
top of the inflated armrest.
Step 2.
Slide the battery assembly into the control arm sleeve. Be careful not to
damage the wire inside the battery assembly when sliding it into the sleeve.
Step 3.
Unscrew the cap from the battery assembly and to open the battery compartment.
Insert 6 D-cell batteries (not included) into the compartment, making sure to
follow the polarity (+/-) as marked inside the compartment. When all batteries
are inserted, replace the cover on the battery compartment, and secure the
cover with the cap by pressing down and tightening clockwise.
Note : Make sure the cover is properly aligned with the battery compartment as you close the compartment. The cover and compartment are designed with notches to ensure correct alignment. Rotate the cover until the notches in the cover fit into the notches in the compartment itself
Step 4.
Connect the wires from the bottom of the battery compartment (which should now
be underneath your inflatable) to the propeller assembly by inserting the male
power plug from the battery into the female outlet on the propeller. Be
careful not to damage the wires.
Step 5.
Align the tabs on the propeller assembly with the openings in the download of
the battery compartment. Slide the top stem from the propeller into the
battery compartment downrod. Squeeze the tabs on the sides of the top stem of
the propeller to allow the steam to fully insert. The propeller assembly and
the battery compartment assembly should ‘click’ into place.
Step 6.
Repeat the steps above on the other side of the raft. Be careful not to damage
the propeller when moving your Splash Runner during assembly.
TESTING the SPLASH RUNNER
After completing the previous assembly steps, press the button on the handle to test the propeller. If the propeller doesn’t move, check to make sure that all electrical connections are complete, and that the battery cover is correctly aligned and completely closed.
HOW to USE YOUR SPLASH RUNNER
CONTROLLING the SPLASH RUNNER
Your Splash Runner is perfect for your backyard pool or a small lake. Because it contains propellers on either side, it enables you to move in all directions.
- To move, press the buttons on both handles. These buttons will operate your propellers.
- To drive forward, turn both handles so they are facing forward and press both buttons at the same time.
- To drive in reverse, turn both handles so they are facing backward and press both buttons.
- To turn right, turn either handle to the right. The angle of your turn will depend on how much you turn the handles to the right.
- To turn left, turn either handle to the left. The angle of your turn will depend on how much you turn the handles to the left.
- To move laterally towards the right, turn both handles right and press both buttons.
- To move laterally towards the left, turn both handles left and press both buttons.
- To rotate in a circle, face one propeller forward and the other backward and press the buttons.
DISASSEMBLY
To disassemble your Splash Runner, please follow these instructions: First,
unscrew the cap from the battery compartment and remove the cover. Remove all
batteries. It is a good idea to immediately replace the battery cover and cap
so that you don’t lose them. Next, separate the propeller from the battery
compartment assembly by squeezing the tabs where they are connected. Squeeze
both tabs and pull the propeller down. Be careful not to pull the propeller
out too fast or far, as this may damage the electrical wires.
Finally, separate the electrical connection between the propeller and the
wires from the battery compartment by pressing the small tab on the male plug
and pulling it away from the female connection. Once the propeller is
disconnected from the wiring on the battery compartment assembly, you can
remove all parts from the inflatable.
Note : Be sure to disconnect the electrical by pulling the plastic plugs,
not the wires themselves. Pulling on the wires can damage the assembly.
REPAIRING the SPLASH RUNNER
Rough surfaces may puncture the Splash Runner. If the lounger gets punctured, use the glue and PVC from the repair kit to seal the punctured surface. Apply the glue on the damaged area and apply the supplementary PVC sheet. Wait approximately one minute after applying the PVC sheet for the glue to dry before handling your Splash Runner. You should wait 24 hours before using the Splash Runner in the water again.
WARNING
Please read the User’s Guide carefully before operating the product.
- Children under 14 years of age should not operate this product without parental supervision.
- This product is designed for pool and lake use only. It may be used in ponds or small lakes only within the range of the user’s comfortable ability to swim to shore. Do not use in areas where there are strong currents, waves, or watercraft present which could create wakes. Do not use in any other body of water or saltwater.
- This product is designed to hold one person not exceeding 300 lbs/135 kg.
- Keep hands, hair, and loose objects such as clothing away from the propeller.
- If an object becomes lodged in the propeller, make sure that this product is turned off before attempting to dislodge it.
- Always inspect the pool area before use to ensure it is free of hazards and/or obstacles, such as pool toys and swimmers.
- Never ride into or over swimmers.
- Keep this product away from hot or sharp objects.
- Always use caution and common sense.
- Never jump or dive off this product.
SPECIAL CARE & HANDLING
- Avoid rough handling such as bumping or dropping.
- Avoid extreme temperatures. For best results use between the temperatures of 39° F and 120° F (4° C and 38° C).
- Clean using only a slightly damp cloth. Do not use cleaners with chemical agents.
BATTERY INFORMATION
- Your Motorized Pool Lounger uses 12 D batteries (6 per propeller), not included.
- Do not mix alkaline, standard (carbon-zinc) or rechargeable nickel-cadmium) batteries.
- Do not mix old and new batteries.
- Do not use rechargeable batteries.
- Remove exhausted batteries from the unit.
- Do not short circuit battery terminals.
- Remove batteries and store them in a cool, dry place when not in use.
- To avoid explosion or leakage, do not dispose of batteries in a fire or attempt to recharge alkaline or other non-rechargeable batteries.
If you have any questions or would like additional information on PoolCandy products, please contact us at service@banddgroup.com.
THE MOTORIZED POOL LOUNGER IS NEITHER A PERSONAL-FLOTATION NOR A LIFESAVING
DEVICE. ALL USERS SHOULD KNOW HOW TO SWIM.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
CONTENTS :
•ONE INFLATABLE POOL LOUNGER
• 2 x BATTERY-OPERATED MOTORS
• PATCH KIT
• INSTRUCTION MANUAL
Model No. PC4000SR
WARNING THIS IS NOT A LIFESAVING DEVICE.DO NOT LEAVE CHILD UNATTENDED WHILE DEVICE IS IN USE.
Made in china DISTRIBUTED BY B &D GROUP,LLC MIAMI,FL33186