JBC GSFR10V03 Guide Kit for SFR Instruction Manual

JBC GSFR10V03 Guide Kit for SFR

Packing List

Guide Kit with Solder Wire Perforation
The following items are included. See Exploded View (page 8) for references.

Guide Kit without Solder Wire Perforation
The following items are included. See Exploded View (page 9) for references.

Assembly: GSFR Wheels to SFR

For this operation, disconnect the device, and take off the cover by pressing the tabs. First disassemble the guide tube (6), the nozzles (1)+(4), then the Wheels, Blade and Clamp (2)+(3). Disassemble the Counter Wheel (5). Use the Allen key and the spanner, provided with SFR.

Assembly with Solder Wire Perforation

1.  Assemble the counter wheel (1).
2.  Insert the intermediate nozzle (2) until its collar rests against the housing and tightens the screw.
3.  Assemble the inlet nozzle (3) and tighten the screw.
4.  Assemble the guide wheel (4) and tighten the screw. Attention: Always use the correct wheel set for each wire thickness.
5.  Assemble the blade first, then mount the blade clamp (5) onto the same axis and tighten the screw. Caution: handle the blade carefully to avoid injury

Assembly without Solder Wire Perforation

1.  Assemble the counter wheel (1).
2.  Insert the intermediate nozzle (2) until its collar rests against the housing and tighten the screw.
3.  Assemble the inlet nozzle (3) and tighten the screw.
4.  Assemble the support wheel (4) and tighten the screw. Attention: Always use the correct wheel set for each wire thickness.
5.  Assemble the traction wheel (5) onto the axis and tighten the screw.

Assembly: GSFR Tube to SFR and TRA

1.  Assemble SFR to TRA with the screws.
2.  Assemble GSFR Guide Tube to TRA and tighten the screw.
3.  Assemble the Outlet Nozzle onto the Dispensing Tube.
4.  Assemble GSFR Bushing into SFR hole and tighten the screw.
5.  Finally attach the Reel Support to SFR with its screw.

Solder Wire Loading

GSFR must be assembled previously.

1.  Feed the Solder Wire into the Inlet Nozzle until it reaches the wheels.
2.  Make sure the wire passes through the Intermediate Nozzle and enters into the Guide Tube.
   Important: Set the wire thickness parameter before starting to dispense the wire. To set the W-THI command see the Communication Protocol for the SFR unit at www.jbctools.com/jbcsoftware.html. Wire feeding is controlled by an external controller (Robot/PLC/Computer). To start the wire loading process use the W-SLD command. See the Communication Protocol for the SFR unit at www. jbctools. com/jbcsoftware.html

Maintenance

•  Before carrying out maintenance, always unplug the tool and the device.
•  Use a damp cloth to clean the tool. Alcohol can only be used to clean the metal parts.
•  Periodically check that the metal parts of the mechanism are clean.
•  Keep Dispensing Nozzle Tip clean to avoid solder feeding obstruction.
•  Periodically check all cables and tube connections.
•  Replace any defective or damaged parts. Use original JBC spare parts only.
•  Repairs should only be performed by a JBC-authorized technical service.

Safety

•  Do not use the device for any other purpose.
•  Be sure that the power supply is disconnected before changing any spare parts.
•  Avoid flux coming into contact with skin or eyes to prevent irritation.
•  Be careful of fumes produced while soldering.
•  Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves while handling components to avoid personal injury.
•  Utmost care must be taken with liquid tin waste which can cause burns.

Exploded View

References

• JBC Soldering Stations, Irons and Rework equipment for electronics
• JBC Software
• Warranty Extension

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>