Thermostat Salus User Guide

Thermostat Salus

Thermostat Salus

Introduction

The RT510BC+ thermostat will switch your heating system on or off, as needed, in accordance with the time and temperature set by you. It can be used with the RXBC605 integral plug-in RF boiler control. The RF boiler control is a direct replacement for the basic time clock or blanking plate usually supplied with the boiler. Installing the RF boiler control takes minutes. Once installed, you will benefit from all the control features of the RT510BC+ thermostat.

Product Compliance

This product complies with the essential requirements and other relevant provisions of the following EU Directives: EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity is available on www.saluslegal.com

868.0-868.6MHz; <13dBm

Safety Information

Use in accordance with the regulations. Indoor use only. Keep your device completely dry. Disconnect your device before cleaning it with a dry cloth. This accessory must be fitted by a competent person, and installation must comply with the guidance, standards and regulations applicable to the city, country or state where the product is installed. Failure to comply with the relevant standards could lead to prosecution

Always isolate the AC Mains supply before installing or working on any components that require 230 VAC 50Hz supply.

Box content

RXBC605 Installation

1. Remove the front panel from the boiler.
2. Do not remove boiler loop.
3. Replace the front panel ensuring a good seal is made.
4. Connect the electrical plug.
5. Pull out the mechanical timer.
6. Push fit boiler control into housing.
7. Power up the boiler and check the correct operation.

RXBC605 Wiring Terminals

RXBC605 User Controls

RXBC605 Switch Position

1. AUTO mode. When the switch on the Boiler Control is in the AUTO (normal) position, the Boiler Control will automatically receive the RF signal from the transmitter and control the boiler based on the programming of the transmitter.
2. MANUAL mode. The user can also move the switch to the MANUAL position; when in this mode, the boiler will be always turned on and the LED indicator will also be lit constantly. The manual mode is only to be used as a temporary control if problems develop with the communication from the thermostat.

When the thermostat is operating in NORMAL mode, if the Boiler Control has not received a signal from the transmitter after 1 hour, the Boiler Control will turn off the boiler, and the LED indicator will flash constantly (two times every second). Once the Boiler Control receives a valid ON or OFF signal, the Boiler Control will control the heating system accordingly.

RT510BC+ (Thermostat) Button Functions

RT510BC+ (Thermostat) Dip Switch Settings

The DIP Switches can be found on the rear of your thermostat. For all plug-in boiler receiver applications ensure SW1 is set to RAD.

Test the Pairing Process

During test pairing, boiler control should flash confirming pair. If not, please follow Pairing Process.

Pairing Process

(1) Press the SYNC button for 3 seconds until LED starts flashing

(2) The LG+5V is ready to be paired with your thermostat.

(3) Begin the pairing process

(4) End the pairing process

Setting Time and Date

Press the buttons together for 3 sec

Press UP or DOWN to select the hour format and then press SELECT to confirm your option.

Press UP or DOWN to select the hour and then press SELECT to confirm your option.

Press UP or DOWN to select the minutes and then press SELECT to confirm your option.

Press SET to return to the Main Screen.

Continue with the same steps for setting the Day

Programming

You can create personalized programmed for your controller. You have the option to choose between a 5-2 days programmed or a daily one by using the parameter d04 from Installer mode

Press SET to change your programmed.

Press UP or DOWN to select Weekday/Weekend/ Day and press SELECT.

Press UP or DOWN to set the hour and press SELECT to confirm your option.

Press UP or DOWN to set the minutes and press SELECT to confirm your option.

Press UP or DOWN to set the temperature and press SELECT to confirm your option.

Follow the same procedure for the next set of time.

After you have done all the changes, please press SET to confirm all your choices and to return to the Main Screen.

Review the Setpoint (desired) temperature

Actual room temperature
Setpoint (desired) temperature

Temporary Override

Press UP or DOWN to review the setpoint temperature.

Press UP or DOWN to set the temperature

Press SET to confirm the changes

Permanent Override

Press OVERRIDE in order to activate the mode.

Press UP or DOWN to set the temperature

Press SET to confirm the changes
The Override sign will appear on the Main screen.

Boost function

Press +Hr. to activate the Boost function.

Press +Hr. to set boost hours and then press UP or DOWN to set the boost temperature
for your boost period.

Frost protection

Press the FROST button once to activate the function.

Frost Mode ON.

Press the FROST button once to deactivate the function.

Frost Mode OFF.

The Frost protection temperature can be reviewed by pressing the UP button once, but can only be changed in Installer Mode.

Holiday Mode

Press the HOLIDAY button for 3 sec

Press the UP or DOWN button to set the Holiday period.

Press the HOLIDAY button for 3 sec to exit Holiday Mode.

You can also exit Holiday Mode by setting the days to zero.

Installer Mode

Press the three buttons together simultaneously for 3 seconds.

Reset function RT510TX+

Remove the batteries without pressing any button. Wait 2 minutes and insert the batteries
again. Your device will be restarted.

NOTE:
If you do not notice the “low battery” symbol displayed on the screen in time, it will shut down. In this case, after removing the old batteries, it is necessary to wait 5 minutes before inserting the new batteries. Otherwise, it is possible that a condenser will remain partially discharged and it can prevent the thermostat from restarting.

When you want to change the batteries your device will use the internal memory to backup your settings. You have 30 seconds to change the batteries before losing your settings.

SALUS Controls plc
SALUS House
Dodworth Business Park South,
Whinby Road, Dodworth,
Barnsley S75 3SP, UK.
T: +44 (0) 1226 323961
E: sales@salus-tech.com
E: techsupport@salus-tech.com

www.salus-tech.com

SALUS Controls is a member of the Computime Group.
Maintaining a policy of continuous product development SALUS Controls plc reserve the right to e. change specification, design and materials of products listed in this brochure without prior notice

For PDF Installation guide please go to www.salus-manuals.com

Issue Date: February 2018

DOWNLOAD RESOURCES

• SALUS Thermostat Salus [pdf] User Guide Thermostat Salus
• Read more: https://manuals.plus/salus/thermostat-salus-manual#ixzz7i0qWH9G0

FAQ’S

How do I connect the thermostat to my boiler?

The RF boiler control is a direct replacement for the basic time clock or blanking plate usually supplied with the boiler. Simply remove the existing time clock and replace it with the RF boiler control.

How long will it take to install?

The RF boiler control is a direct replacement for the basic time clock or blanking plate usually supplied with the boiler. Simply remove the existing time clock and replace it with the RF boiler control.

What are the benefits of using an integrated thermostat?

An integrated thermostat will allow you to control your heating system from a single point, and can provide you with useful information about your home’s energy consumption. It will also allow you to set up a schedule so that your heating system can be programmed to switch on or off at specific times.

How do I reset my Salus wireless thermostat?

To perform a Factory Reset on the RT310RF Thermostat, simply remove the batteries without pressing any button. Wait for 2 minutes and then re-insert the batteries.

How do I know if my Salus thermostat is working?

To test that the receiver and thermostat are paired, navigate to the Pairing Menu by choosing Menu > Pairing > TEST. This will display ‘TESTING 10’ on the thermostat. If the receiver and thermostat are paired correctly, the RED and GREEN LED’s on the receiver will flash.

How do I change the battery in my Salus thermostat?

Slide down the front cover and fully remove the batteries from the device and leave for a minimum of 10.

How do I know if my thermostat battery is bad?

When the batteries are nearly depleted, a low battery indicator will appear on your thermostat’s display. Some thermostats feature a light in lieu of an on- display indicator. At this point, your batteries may have another month or two of life remaining, making it a good time to change your batteries.

How do you use Salus heating control?

Press Up/Down to set the temperature. Note: To exit the temporary override procedure, you can wait for 3 seconds until the set temperature stops flashing or you can press on the SET button once. Press Override in order to activate the mode. Press Up or Down to set the temperature.

What does the hand symbol mean on Salus?

This will put the thermostat into Manual mode and prevent any Program Schedules from running. A Hand Symbol will be displayed on the screen to show you are in Manual Mode.

How do you turn hot water on Salus?

To Activate: Press the Cog key to toggle to the hot water zone.

Why is Salus thermostat flashing?

Description : A red flashing light on your Receiver means that the communications link between your Thermostat and Receiver has been lost and your devices need pairing. Your Thermostat will be failing to control your boiler and your heating will not be working. Please follow the procedure below to resolve this issue.

How do you turn Salus off?

Press the FROST button once to deactivate the function. Press SET to confirm the changes. Press the buttons together for 3 sec.

VIDEO

Thermostat Salus
www://saluscontrols.com/

References

• salus-manuals.com
• salus-tech.com
• Legal – Salus

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>