SALUS HTRS-RF(30) Wireless Digital Room Thermostat User Manual

SALUS HTRS-RF(30) Wireless Digital Room Thermostat

Product Information

Specifications:

• Producer: SALUS Controls Plc

• Address: Units 8-10 Northfield Business Park
  Forge Way, Parkgate, Rotherham S60 1SD, United Kingdom

• Website: www.saluscontrols.com

• Group: SALUS Controls is a member of the Computime Group

• Issue Date: April 2019

• Version: V019

• Model: RT310iSPE HTRS-RF(30)

Product Usage Instructions

Installation Guide:

Follow the steps outlined in the installation guide provided with the product to set up the RT310iSPE HTRS-RF(30) effectively.

Operation:

To operate the product:

1. Make sure the device is properly installed and powered on.
2. Refer to the user manual for detailed instructions on setting up and using the product.
3. Follow the on-screen prompts or buttons to navigate through different functions.
4. Adjust settings as needed for optimal performance.

Maintenance:

Regular maintenance is essential for prolonging the lifespan of the RT310iSPE HTRS-RF(30). Keep the device clean and free from dust or debris. Refer to the user manual for specific maintenance guidelines.

Troubleshooting:

If you encounter any issues with the product, refer to the troubleshooting section of the user manual. Contact customer support if problems persist.

Frequently Asked Questions

• Q: Can I control multiple heating zones with the RT310iSPE HTRS-RF(30)?
  • A: Yes, the RT310iSPE HTRS-RF(30) supports multi-zone control. Refer to the user manual for instructions on setting up and managing multiple heating zones.
• Q: Is it possible to program a heating schedule with thisproduct?
  • A: Yes, the RT310iSPE HTRS-RF(30) allows for programming heating schedules. Follow the programming instructions in the user manual to set up your desired schedule.
• Q: What should I do if the device stops responding?
  • A: If the device stops responding, try resetting it by following the instructions in the user manual. If the issue persists, contact customer support for further assistance.

Introduction

HTRS-RF(30) is a wireless digital room thermostat compatible with devices that are part of the iT600 series, such as: KL08RF wiring centre, TRV10RFM thermostatic radiator valve and RX10RF boiler receiver. If you want the thermostat to control the devices via Internet (Online Mode), please use the UG600 universal gateway and connect it to the SALUS Smart Home app. You can also use the thermostat to control the devices locally without Internet connection (Offline Mode) but in this case the communication between devices must be done using the CO10RF coordinator.

Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity on www.saluslegal.com 2405-2480MHz; <14dBm

Safety Information

Use in accordance with the regulations. Indoor use only. Keep you device completely dry. Disconnect your device before cleaning it with a dry cloth.

Wiring diagram

Power supply:

• 2 x AA alkaline batteries

S1 & S2 terminals:

• external temperature sensor (air or floor)
• external switch (occupancy sensor)

Mounting:

• surface mounting (after removing the back case)

LCD icons

1. Comfort temperature
2. Standard temperature
3. Reduced temperature
4. Auto mode
5. Frost protection mode

Button functions

Button combinations

Zigbee network coordinators

1. Online: connected to the Internet using the UG600 universal gateway.
2. Offline: with the possibility of connecting to the Internet using the UG600 universal gateway.
3. Offline: without any possibility of connecting to the Internet using the CO10RF coordinator.

Select the device that is going to be controlled by the thermostat and the type of Zigbee network coordinator you want to use. Install the devices according to the instructions attached to each product.

Power up

After inserting the batteries, the thermostat will display the software version and it will power up.

After the first power-up, you can choose to pair the thermostat either with underfloor heating (UFH) or with radiators (rAd):

• KL08RF wiring centre
• TRV10RFM thermostatic radiator valve

Extended configuration

Extended configuration should be used only if you want to pair the thermostat with the boiler receiver. To do so, press the buttons shown below simultaneously until all visible icons flash once.

Choose the device type according to the screens below:

• Underfloor heating
• Radiator heating
• RX10RF in RX1 mode
• RX10RF in RX2 mode

OFFLINE

The offline pairing method should be used by non-internet users only.

WARNING! Do not use the CO10RF coordinator with UG600 simultaneously.

Pairing with the Wiring Centre

3 Open the ZigBee network

• Select the wiring center number using (max 9). Confirm your choice by pressing

• Select the group number (offline only) using . Confirm your choice by pressing

• Select the zone number using . Confirm your choice by pressing

9 Close the ZigBee network

Pairing with the TRV

WARNING! You can connect up to 6 TRVs to one thermostat

• Press and hold the button for 10 seconds. The LED will start flashing red.
• Select rad on the LCD

5 Open the ZigBee network

Press to confirm the pairing with the TRV

Press . The LED on the TRV will flash green one time and then it will turn off.

The LCD will display the number of paired devices.Press to finish

10 Close the ZigBee network

Pairing with the boiler receiver

WARNING! In a ZigBee network, you can use only one RX10RF configured as RX1 and only one RX10RF configured as RX2

In order to pair directly the thermostat with the boiler receiver, please follow the Extended configuration procedure.

3 Open the ZigBee network

6 Close the ZigBee network

ONLINE

Please use the online pairing method when you are using UG600 to configure your system. Follow the on-screen instructions to complete the setup

Go to the App

16 Once you have selected your device type, follow the onscreen instructions to complete the setup.

Identify paired devices

Go to Installer Mode, select parameter 00 and press

The LEDs on the paired devices will start to flash.

Press to exit installer mode

Change temperature setpoint

If thermostat works in AUTO mode, then the overwritten temperature (temporary override) will be maintained until next program. In manual mode and frost protection mode temperature change is permanent

Factory Reset

References

• Choose your country – Salus

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>