SALUS EP110/EP210/EP310 Electronic Programmable Timer Installation Guide

**SALUS EP110/EP210/EP310 Electronic Programmable Timer Installation Guide

**

Introduction

A programmable controller is used to switch the heating system and/or the hot water in your home on and off as needed. It works by controlling the central heating and/or the hot water with programmed settings that take effect at different times of the day.
Go to www.salus-manuals.com for the full PDF version of the manual.

Product Compliance

EU Directives: 2014/30/EU, 2014/35/EU and 2011/65/EU. Please check www.saluslegal.com for the full information.

Safety Information

Use in accordance with the EU and national regulations.
For indoor use only.
Keep your device completely dry.
This product must be installed by a competent person and in accordance with all the EU and national regulations.

Difference between EP110/EP210/EP310

EP110|
CH or HW|
---|---
EP210
CH and HW|
EP310
2x CH and 1x HW|

The EP line will offer you the possibility to customize your central heating system and hot water system as desired.
EP110 is recommended for users that want to control only the Central Heating or the Hot Water system.
EP210 is designed to give you a full control with only one device of both your Central Heating and Hot Water system.
EP310 is the most versatile product of this line and lets you manage two different Central Heating zones and the Hot Water with only one controller.

• Input: 230V, 50Hz
• Output: 3A/ switch terminal

Installation

EP110 Volt Free application only

Note: Please remove red link wire for this application

/SALUS-EP110EP210EP310-Electronic-Programmable-Timer-Installation-Guide-5.png)

L| Mains Live
1| Not Used
2| Not Used
3| Volt Free Connection
4| Volt Free Connection
| Earth Parking (no electrical connection)

EP110 – 230V Application Only

EP210 – 230V Application

L| Mains Live
1| Hot Water Off
2| Central Heating Off
3| Hot Water On
4| Central Heating On
| Earth Parking

(no electrical connection)

EP310 – 230V Application

/SALUS-EP110EP210EP310-Electronic-Programmable-Timer-Installation- Guide-10.png)

L| Mains Live
1| Hot Water Off
2| Central Heating Off
3| Hot Water On
4| Central Heating 1 On
5| Central Heating 2 On
6| Central Heating 2 Off
 | Earth Parking

(no electrical connection)

Jumper Settings

Changes to the jumpers settings should only be made by the Engineer carrying out the installation or other qualified person. The installer should select the jumper positions required if changes need to be made to the factory default settings.
These jumpers are found on the rear of the controller.

• **EP110/EP310

**

• EP210
  
  

EP110/ EP210/ EP310 Switching Bridges

Switch| Feature| EP110/310 Settings| EP210 Settings
System| Fully pumped system(P) or gravity-fed hot water system(G)| NA| NA| P| G

Program| 5-2 days programme or 24h programme| 5-2| 24H| 5-2
| 24H
Memory Backup| Disable/enable the internal backup battery| OFF| ON| OFF| ON

• P – Fully pumped system for independent Central Heating and Hot Water.
• G – Gravity Hot Water system with Pumped Central Heating

First Power Up

• EP110
  
  

• EP210
  
  

• EP310
  
  

Button Function

Backlight/ Holiday
|

1. Turn on the LCD backlight
2. Press for 3 sec to activate Holiday mode

---|---
Mode
| Select operating mode (ON, ONCE, AUTO, ADV, OFF)
+1Hr
| Activate/deactivate Boost function
Down
| Decreases the selected setting
Up
| Increases the selected setting
Select
| Select a clock or programme setting
Set
| Sets a clock or programme setting
Reset
| Reset to Factory settings

Setting date and time

Operating Modes

All three models have the following five Operating modes. You can select them by pressing the MODE button.

selecting Advance (ADV). This will move the unit into the next program. When the ADV function ends the device will return to normal program.
OFF| Continuously off

Note: In ONCE or AUTO mode, by long pressing the MODE button, the controller will switch automatically to ADV. You can cancel the ADV by long pressing the MODE key. The device will then return to ONCE or AUTO mode.

Programming the EP110; EP210; EP310

You can create personalized programmes for your controller. You have the option to choose between a 5-2 days programmes or a daily one by using the jumpers.

5-2 Days Programme

EP110 (1 Channel)| EP210 (2 Channels)| EP310 (3 Channels)
Weekdays
3 sets of time/channel Weekends
3 sets of time/channel| Weekdays
3 sets of time/channel Weekends
3 sets of time/channel| Weekdays
3 sets of time/channel Weekends
3 sets of time/channel
Total: 6 settings/week| Total: 12 settings/week| Total: 18 settings/week

EP110

Please repeat the procedure for all the programmes and channels that are available for this model.

EP210

Please repeat the procedure for all the programmes and channels that are available for this model.

EP310

Please repeat the procedure for all the programmes and channels that are available for this model.

Individual days programme

EP110 (1 Channel)| EP210 (2 Channels)| EP310 (3 Channels)
1 Day
3 sets of time/channel
Total: 21 settings/week| 1 Day
3 sets of time/channel
Total: 42 settings/week| 1 Day
3 sets of time/channel
Total: 63 settings/week

Note: Don’t forget to move the jumpers to 24h in order to have the individual programme active. After that please follow the same instructions as for the 5-2 days programme.

he circle will be rotating for EP110 and for EP210/EP310 will remain steady when the relay output is ON. For EP210 and EP310 the and  / or icon will be visible on the screen.

Change the channels for EP210/ EP310

For changing the channel of your device (CH and/or HW) press the Mode button with the desired channel. The procedure is the same for EP210/EP310.

Other Functions

1. +Hr Program Override (Boost)
   This function is available in ONCE/AUTO/ADV/OFF. After pressing the button, the function will be immediately applied. You can override the program for maximum 9 hours. For cancelling the Boost function, press the  button repeatedly until the +8 hours disappears.

2. BL/Holiday function
   Press the button once and the backlight will be turned on.
   Press and hold the  button for 3 seconds to activate the Holiday Mode.
   Press  or  to select the number of days for the Holiday Mode and  to confirm your choice.
   Press and hold the button for 3 seconds to cancel the Holiday Mode.

3. Factory Reset
   If you want to return to the factory settings please press the Reset button once (use a pin for this action)

Customer Support

E: tech@salus-tech.com
T: +44 (0) 1226 323961

References

• salus-manuals.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>