SALUS RT310i Smart Phone Controlled Programmable Thermostat Installation Guide
- June 3, 2024
- SALUS
Table of Contents
SALUS RT310i Smart Phone Controlled Programmable Thermostat
View all SALUS thermostat manual
Introduction
The SALUS RT310i is a Smart phone controlled programmable thermostat. The RT310i thermostat will switch your heating system on or off, as needed, in accordance with the temperature set by you, locally on the device or remotely using the dedicated app.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity on www.saluslegal.com 868.0 868.6MHz; <13dBm
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your equipment completely dry. Disconnect your equipment before cleaning it with a dry towel.
Always isolate the AC Mains supply before installing or working on any components that require 230 VAC 50Hz supply.
The thermostat is pre-set from factory in Manual Mode allowing you to set the desired temperature. This is the default working mode if not connected to the internet during installation.
Button Functions
❶ Turn on the LCD backlight
❷ Turn On/Off the Frost Mode
❸ Increase button
❹ Decrease button
❺ Test Mode/ Pairing Mode
Installation
Installation – Step 1
RXRT510
Wire up the receiver according to the diagram and switch it on before
inserting the batteries into the thermostat.
The thermostat and the receiver are pre-paired from factory.
Installation – Step 2
RT310iTX
Before inserting the batteries, please make a note of your SRT number and
register your device on the app.
Installation – Step 3
iTG310
Connect the gateway to your router. Gateway is online when the green LED is on
Pairing Process
Press the button for 3 sec. Wait 9 min or if the red light goes steady, press the pairing button again for 3 sec.
If you want to re-pair thermostat with the receiver, make sure that the device
is disconnected from the power supply and the switches on the receiver have
been set to AUTO and ON. Then connect the receiver to the power supply and
wait for the red LED to light steadily. Next switch to the OFF position and
again to ON position quickly. The red flashing LED will confirm entering the
pairing mode.
Registration
Download the RT310i App, create an account and register your device. Follow the on screen instructions to complete all the steps.
Device Settings Via the App
Features available only on the App:
- Temperature format
- Clock format
- Time zone
- Daylight Saving Time
- Heating or Cooling Mode
- Temperature accuracy
- Display tolerance
- Temperature offset
- Schedule/Manual/Off Mode
- Holiday Mode
- Location Mode
- Delay Start
Customize your settings according to your preferences. Time and date will be
set automatically once connected to the internet. Set the mode (heat/cool).
Heat Mode is used for controlling a heating boiler. Cool Mode is used for
controlling a cooling device. In Cool Mode, you can choose temperature
accuracy between ± 0.5 °C and ± 0.25 °C. In Heat Mode, you can select as well
between a lower comfort level (6 on/off cycles per hour) and a higher comfort
level (9 on/off cycles per hour). Also, in order to calibrate the temperature,
you can offset it using a ± 3 °C range.
General Operation
There are 3 program settings. 1. Schedule (7 days, 5-2 days and 24 hours), 2.
Manual and 3. Off.
Schedule Mode
| All | 5/2 | Individual |
|---|---|---|
| Set one schedule for the entire week (each day the same) | Set a schedule for | |
| the working days and for the weekend | Set a daily schedule (each day |
different)
In Manual Mode you will permanently override the schedule. Exit Manual Mode by
switching to Schedule or turning off the thermostat.
If the internet connection is lost the thermostat will follow the schedule. If
it was in Frost Mode you can disable the Frost function from the device and
continue following the schedule (see Frost Mode section of the guide).
Frost Mode
Frost protection temperature can be set between 5.0oC and 9.0oC. To turn on
Frost Mode activate Off Mode or Holiday Mode via the App
Frost Mode can also be de-activated or activated on the device, by pressing
the frost button once.
Holiday Mode
Select the period for this function. Frost Mode temperature will be activated
during this period.
After the Holiday Mode ends, the thermostat will follow the previous setting
(Schedule, Manual or Off.)
Location Mode
Location Mode is an automated task designed to change your heating settings
according to the current distance from your home
If Location Mode is enabled, you can drag the slider in order to set the
distance limit. Go to “Setting” to manage your settings.
Select your devices and the actions you want to take place when you leave and
return home. Choose “SAVE” to confirm. Your devices will be automatically
adjusted to the settings you make.
Customer Support
Head Office:
SALUS Controls plc
SALUS House
Dodworth Business Park South,
Whinby Road, Dodworth,
Barnsley S75 3SP, UK.
T: +44 (0) 1226 323961
E:sales@salus-tech.com
E:techsupport@salus-tech.com
FR/ NL / DE:
support@salus-controls.de
tel: +49 6108 8258515
SALUS Controls is a member of the Computime Group
Maintaining a policy of continuous product development SALUS Controls plc
reserve the right to change specification, design and materials of products
listed in this brochure without prior notice.
For PDF Installation guide please go to
www.salus-manuals.com
Issue date: August 2018
Version: V018
https://thermostat.guide/salus/salus-rt310i-internet-wireless-thermostat- installation-guide/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>