AirFly Pro Instructions: How to Pair & Connect AirPods | User Guide
- June 7, 2024
- twelve south
Table of Contents
- twelvesouth AirFly Pro User Guide
- To Begin, Select Transmit or Receive Mode
- Charging AirFly Pro **
- Turning AirFty Pro On & Off
- Status Light Guide
- FCC Statement
- ISED Statement
- Safety Statement
- NBTC Statement
- RED
- SPECIFICATION
- FAQS
- [AirFly Pro Instructions_](https://manuals.plus/wp-
- VIDEO
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
The twelvesouth AirFly Pro User Guide provides step-by-step instructions on how to pair and connect AirPods or wireless headphones to any headphone jack. The guide includes detailed information on how to use both Transmit and Receive modes, as well as tips and tricks for troubleshooting common issues. The guide also covers how to pair a second set of headphones to AirFly Pro and how to reconnect AirPods or headphones to an iPhone. Additionally, the guide provides information on charging AirFly Pro and turning it on and off. The guide includes a helpful Status Light Guide, as well as important safety statements and compliance information. For any further questions or concerns, users can visit the twelvesouth website or contact support@twelvesouth.com.
twelvesouth AirFly Pro User Guide
twelvesouth AirFly Pro User Guide
To Begin, Select Transmit or Receive Mode
Transmit Mode: to connect AirPods or wireless headphones to any headphone
jack
Transmit Mode (TX) is used to send audio from a wired headphone jack,
such as an airplane TV or treadmill at the gym, to your AirPods or wireless
headphones.
Receive Mode: to wirelessly connect the phone to AUX-IN
Receive Mode (RX) is used to receive Bluetooth audio from a device (such as a smartphone or tablet) and send it to the AUX-IN port of a connected stereo (such as in a car, boat, etc).
Pairing AirFly Pro with AirPods (Transmit Mode)
Press and hold the Power Button for 4 seconds to turn on AirFly Pro. AirFly
flashes amber and white to indicate that it is in pairing mode.*
- If AirFly does not flash amber and white, press the Reset Button on the right side to reset to factory settings.
To enter Pairing Mode on AirPods, first place AirPods inside the charging case. With the lid open, press and hold the button on the back of the Charging Case until the light flashes white.
Once successfully connected, the light on your charging case will turn green, and AirFly Pro will illuminate in white and remain on for 10 seconds.
- This can take up to 90 seconds for initial pairing, but AirFly Pro will remember your AirPods when re-connecting in the future.
Connecting AirFly Pro to Headphone Jack (Transmit Mode)
Plug AirFly Pro into the headphone jack of your preferred entertainment
system.
Pairing AirFly Pro with Wireless Headphones (Transmit Mode)
Press and hold the Power Button for 4 seconds to turn on AirFly Pro. AirFly
flashes amber and white to indicate that it is in pairing mode.
- If AirFly does not flash amber and white, press the Reset button on the right side to reset
Put your headphones into Bluetooth Pairing Mode (refer to your headphone’s owner’s manual for more details).
Once successfully connected; AirFly Pro will illuminate in white and remain on
for 10 seconds.
“This can take up to 90 seconds for initial pairing, but AirFly Pro will
remember your headphones when reconnecting in the future.
Connecting AirFly Pro to Headphone Jack (Transmit Mode)
Plug AirFly Pro into the headphone jack of your preferred entertainment
system.
Pairing with the Second Set of Wireless Headphones
With one set of headphones paired and active, you can then pair the second set
of headphones to AirFly Pro. Double press the Power Button to enter Pairing
Mode (Note: AirFly must already be on to pair.)
Once successfully connected, AirFly Pro will illuminate in white and remain on for 10 seconds.
Reconnecting AirPods / Headphones to iPhone
Once paired, AirFly Pro will remember your AirPods / Headphones and switch to
them when the unit is turned on. To switch back to using your AirPods /
Headphones with your iPhone, first turn off AirFly Pro.
On your iPhone, open Bluetooth Settings, and select your headphones from the
list. The status will change from Not Connected to Connected once headphones
are successfully paired with your iPhone.
Using AirFly Pro with an AUX-IN Port
(Receive Mode)
Toggle AirFly Pro to Receive Mode (RX). Press and hold the Power Button to
turn on AirFly (if it is not already powered on), and AirFly will begin to
blink amber and white once in Pairing Mode.
With AirFly Pro in Pairing Mode, open up the Bluetooth settings on your smartphone. Select AirFly Pro from “other devices” to complete pairing.
Once your phone is connected, plug AirFly Pro into the AUX-IN port of the desired source.
Tips & Tricks
- If only one AirPod seems to be playing audio, turn AirFly Pro off and back on. This will re-sync AirFly Pro and should reconnect both AirPods.
- If you’re having trouble pairing your headphones, make sure that AirFly Pro is switched to Transmit (TX) mode.
- If you want to pair a new set of headphones to AirFly Pro, or clear the pairing list to factory settings, reset AirFly by pressing and holding the Reset button on the side of AirFly for 4 seconds. Once reset, AirFly will blink amber 4 times, and then will go into Pairing Mode.
Charging AirFly Pro **
**
To recharge, simply plug the included USB-C to USB-A charging cable into
AirFly Pro, and then into any powered USB port. AirFly Pro is fully
charged within 2 hours. The internal battery of AirFly Pro lasts about 16
hours.
We recommend fully charging AirFly Pro before using it for the first time. If
your AirFly Pro is low on power, it will flash amber 3 times to alert you that
it will need to be charged soon.
While charging, the AirFly Pro will illuminate in amber and stay on. Once
fully charged, the amber light will turn off.
Turning AirFty Pro On & Off
To turn on AirFty Pro, hold down the Power Button for up to 5 seconds until AirFly Pro lights up. To turn off AirFly Pro, hold down the Power Button for 5 seconds. AirFly Pro will blink amber twice and then power off.
Status Light Guide
Power On : White LED flashes twice
Pairing Mode: White & Amber LED flashes alternately
Unconnected Standby Mode: White LED flashes twice every 5 seconds
Connected Standby Mode: Solid White LED
Low Power: Amber LED flashes 3 times
Charging: Solid Amber
Fully Charged: Amber LED turns off
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used In
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
ISED Statement
This device complies contains a license-exempt transmitter that complies with Innovation Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Safety Statement
– Disposal of a battery into fire or a hot oven, or mechanically crushing or
cutting of a batter–% that can result in an explosion;
– Leaving a battery in an extremely high temperature surrounding environment
that can result in an explosion or the leakage of flammable liquid or gas;
– A battery subjected to extremely low air pressure may result in an explosion
or the leakage
NBTC Statement
This telecommunication equipment conforms to the requirements of the National Telecommunications Commission.
RED
Hereby, Twelve South, LLC, declare that the radio equipment type, Model number 12-1911, is In compliance with Directive 2014/53/EU. The full test of ELI declaration of conformity is available at our website: http://www.twelvesouth.com
Frequency range: 2402 — 2480MHz
Transmission power: 4dBm (conducted)
Have questions?
Visit twelvesouth.com or contact
support@twelvesouth.com
© 2019 Twelve South, LLC. All rights reserved.
SPECIFICATION
Product Name | twelvesouth AirFly Pro |
---|---|
Usage | Pair and connect AirPods or wireless headphones to any headphone jack |
Transmission Modes | Transmit Mode (TX) and Receive Mode (RX) |
Pairing | Pairing with AirPods or wireless headphones in Transmit Mode and |
pairing with smartphone in Receive Mode
Charging| USB-C to USB-A charging cable, fully charged within 2 hours,
internal battery lasts about 16 hours
On/Off| Hold down Power Button for up to 5 seconds to turn on/off
Status Light Guide| Power On: White LED flashes twice, Pairing Mode: White &
Amber LED flashes alternately, Unconnected Standby Mode: White LED flashes
twice every 5 seconds, Connected Standby Mode: Solid White LED, Low Power:
Amber LED flashes 3 times, Charging: Solid Amber, Fully Charged: Amber LED
turns off
FCC Statement| This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
ISED Statement| This device complies contains a license-exempt transmitter
that complies with Innovation Science and Economic Development Canada’s
license-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept
any interference, including interference that may cause undesired operation of
the device.
Safety Statement| Disposal of a battery into fire or a hot oven, or
mechanically crushing or cutting of a batter-% that can result in an
explosion; Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable liquid
or gas; A battery subjected to extremely low air pressure may result in an
explosion or the leakage
NBTC Statement| This telecommunication equipment conforms to the requirements
of the National Telecommunications Commission.
RED| Model number 12-1911, is In compliance with Directive 2014/53/EU. The
full test of ELI declaration of conformity is available at our website:
http://www.twelvesouth.com Frequency range: 2402 — 2480MHz Transmission power:
4dBm (conducted)
FAQS
does this device also talk to bluetooth speakers from Macbook computers?
If you mean using the macbook headphone jack and transmit to BT speakers, it should, but it may depend on the specific speakers. (Assuming your speakers are not supported by the macbooks’ BT natively or is too laggy for your comfort.)
How do I know if AirFly Pro is working?
A green light on the right side of AirFly Pro indicates that it is receiving power. A white light on the left side of AirFly Pro indicates that it is connected to Apple Watch via Bluetooth A red light indicates there is no audio signal being received by AirFly Pro
How do I connect my iPhone or iPad?
To begin, press and hold the Power Button for 4 seconds until you hear a beep and see a white light illuminate
Is there a way to tell how much battery is left?
No, the AirFly does not have a way to see how much battery is left. However, it can be fully charged in 2 hours and once charged, an AirFly Classic will last around 8 hours (AirFly Duo lasts 20+ hours, AirFly Pro lasts 16+ hours). When the power gets low, the light will flash 3 times.
Does this provide noise cancellation with the AirPods pro
If you’re already using noise cancelling mode – then it follows across.
Does this work on a regular TV?
If the TV has a “speaker” or “audio” out jack then the answer is yes – however, it must be a 3.5mm audio connection, not an RCA jack. I’ve used this when I travel for my wife’s wireless headsets to watch TV while I sleep – as long as there is an “AUX” or audio out 3.5mm jack and you can pair the wireless headset to the Airfly
Will this work with Beats fit pro ear buds?
This works with Bluetooth earbuds and headphones. Very easy to connect.
“airpods must be inside airpod case to enter pairing mode (#1 pairing mistake)” seems obvious that the first mistake was a design flaw?!
AirPods have to be inside the case to pair to your other devices as well so not really a design flaw. The pairing process is very quick and simple.
Will this allow me to pair 2 AirPods to my Mac book?
Yes, you will be able to connect two pairs of AirPods to an AirFly and connect to your laptop to hear audio from it.
Does this work with with other Bluetooth headphones?
Yes, it should work with any and all bluetooth headphones, but due to the vast number of bluetooth headphones out there, it has not been tested with all of them. You should not have any issue though, as long as you follow the specific instructions (PDF file) found on the Twelve South support website.
Why the volume is too low?
the volume is not controling by the Airfly, you can only adjust from the unit where you put the jack and/or from your bluetooth headset if you have a volume control.
Does it receive just audio, or can it receive video as well (see pictures on the cell on TV screen)?
The AirFly Pro receives only audio.
Extension to reach tv sound jack?
Standard part – definitely sold separately.
Can this device be pair with and transmit to a FM bluetooth transmitter?
AirFly plugs into the 3.5mm audio jack of non-Bluetooth devices (such as a television, treadmill, or airplane entertainment system) and transmits the audio to Bluetooth enabled headphones or earpods. However, it cannot go the other way (i.e. It cannot receive Bluetooth. It can only send it.)
Can multiple AirPods be connected? or just one?
Only one at a time
Do you have to re pair it every time you need to connect the AirPods?
No. It automatically pairs after manually pairing it the first time.
How do I pair AirPods with AirFly Pro in Transmit mode?
Press and hold the Power Button for 4 seconds to turn on AirFly Pro. AirFly flashes amber and white to indicate that it is in pairing mode. Place AirPods inside the charging case, with the lid open, press and hold the button on the back of the Charging Case until the light flashes white. Once successfully connected, the light on your charging case will turn green, and AirFly Pro will illuminate in white and remain on for 10 seconds.
How do I pair wireless headphones with AirFly Pro in Transmit mode?
Press and hold the Power Button for 4 seconds to turn on AirFly Pro. AirFly flashes amber and white to indicate that it is in pairing mode. Put your headphones into Bluetooth Pairing Mode (refer to your headphone’s owner’s manual for more details). Once successfully connected, AirFly Pro will illuminate in white and remain on for 10 seconds.
How do I connect AirFly Pro to a headphone jack in Transmit mode?
Plug AirFly Pro into the headphone jack of your preferred entertainment system.
How do I pair a second set of wireless headphones with AirFly Pro?
With one set of headphones paired and active, double press the Power Button to enter Pairing Mode (Note: AirFly must already be on to pair.) Once successfully connected, AirFly Pro will illuminate in white and remain on for 10 seconds.
How do I reconnect AirPods or headphones to an iPhone?
First, turn off AirFly Pro. On your iPhone, open Bluetooth Settings, and select your headphones from the list. The status will change from Not Connected to Connected once headphones are successfully paired with your iPhone.
How do I use AirFly Pro with an AUX-IN port in Receive mode?
Toggle AirFly Pro to Receive Mode (RX). Press and hold the Power Button to turn on AirFly (if it is not already powered on), and AirFly will begin to blink amber and white once in Pairing Mode. With AirFly Pro in Pairing Mode, open up the Bluetooth settings on your smartphone. Select AirFly Pro from “other devices” to complete pairing. Once your phone is connected, plug AirFly Pro into the AUX-IN port of the desired source.
How do I charge AirFly Pro?
To recharge, simply plug the included USB-C to USB-A charging cable into AirFly Pro, and then into any powered USB port. AirFly Pro is fully charged within 2 hours. The internal battery of AirFly Pro lasts about 16 hours.
How do I turn on and off AirFly Pro?
To turn on AirFty Pro, hold down the Power Button for up to 5 seconds until AirFly Pro lights up. To turn off AirFly Pro, hold down the Power Button for 5 seconds. AirFly Pro will blink amber twice and then power off.
Is there a way to tell how much battery is left?
No, there is no way to tell how much battery is left.
Does AirFly Pro provide noise cancellation with the AirPods pro?
If you’re already using noise cancelling mode – then it follows across.
Will AirFly Pro work with a regular TV?
Yes, AirFly Pro will work with a regular TV as long as it has a headphone jack.
Will AirFly Pro work with Beats fit pro ear buds?
Yes, AirFly Pro will work with Beats fit pro ear buds as long as they are wireless headphones that can be paired with Bluetooth.
[AirFly Pro Instructions_](https://manuals.plus/wp-
content/uploads/2021/07/AirFly-Pro-Instructions-How-to-Pair-Connect-AirPods- -User-Guide.pptx-1.pdf)
VIDEO
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>