Shark SV1100 Series Navigator Freestyle Cordless Vacuum FAQs
- June 9, 2024
- Shark
Table of Contents
- Shark SV1100 Series Navigator Freestyle Cordless Vacuum FAQs
- FAQs
- How long does it take to charge the vacuum?
- How to clean the filters?
- How to clear debris from the brush roll?
- How long is the runtime?
- Why is the Max fill line at the half point of the dust cup?
- How to clear the air hose/neck of the floor nozzle?
- Why is the light around the power button blinking?
- How to tell if the vacuum is charging?
- What are the dimensions?
- What is the weight?
- What is the Amperage?
- What is the Voltage?
- What is the Wattage?
- What is the dust cup capacity?
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Shark SV1100 Series Navigator Freestyle Cordless Vacuum FAQs
This article contains the FAQs for the SV1100 Series Shark Navigator® Freestyle. This supports the following product SKU100, SV1100, SV1100C, SV1106, SV1106BRN,SV1107,SV1110, SV1112,SV1112BRN, SV1112C, SV1112QGA, SV1112QGN, SV1112QPR, SV1112QRD,SV1112QRG,SV1115.
FAQs
How long does it take to charge the vacuum?
Charge the machine for 6 hours before your first use. After 3-to-5 charges, your charge time is only 3-6 hours. You will know when the maximum charge has been achieved when you see that both halves of the charging light are illuminated to show a complete oval.
How to clean the filters?
Remove the dust cup from your machine. You will now see the foam filter underneath. Take that filter out rinse under lukewarm water until the water runs clear. Now squeeze the excess water out of the filter and let it air dry for 24 hours before replacing them. Do NOT operate your unit with a wet filter or without the filter in place.
How to clear debris from the brush roll?
Ensure you are in a well-lit area and that the machine is turned off. Remove the power head/floor-nozzle by pressing the button on the back of the machine and pulling it the nozzle away from the rest of the machine. You may need a flashlight. Cut away any wound hair with scissors. Before replacing the head/nozzle, check the neck which connects it to the machine for any more blockages.
How long is the runtime?
A full charge can last up to 24 minutes on the bare floor setting. The carpet setting can vary depending on the carpets which are being cleaned with an average of 17 minutes.
Why is the Max fill line at the half point of the dust cup?
Some air flow is needed inside your dust container to ensure maximum suction.
How to clear the air hose/neck of the floor nozzle?
After removing your floor nozzle, flip back the connector to straighten the air passage/hose and carefully remove any hair or debris which may have built up or become logged in. Be careful to not use any sharp objects as these could damage the hose.
Why is the light around the power button blinking?
Something has jammed in your brush roll. Turn off the machine, remove the floor nozzle and inspect for any blockages to remove.
How to tell if the vacuum is charging?
Once the charger/AC Adaptor is connected and plugged into an outlet, the indicator light around the power button will turn on in a half-oval shape. When the charging cycle is complete, both halves of the oval will be illuminated.
What are the dimensions?
9.6″(L)x10.5″(W)x46″(H)
What is the weight?
7.5 lbs
What is the Amperage?
11.5 Amps
What is the Voltage?
10.8 volts
What is the Wattage?
125 Watts
What is the dust cup capacity?
0.64 quarts
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>