reloop Portable Performance Controller for Serato Instruction Manual
- June 7, 2024
- reloop
Table of Contents
Instruction Manual
CAUTION!
For your own safety, please read this operation manual carefully before the
initial operation! All persons involved in the installation, setting-up,
operation, maintenance, and service of this device must be appropriately
qualified and observe this operation manual in detail. This product complies
with the requirements of the applicable European and national regulations.
Conformity has been proven. The respective statements and documents are
deposited at the manufacturer.
Please remove the Reloop Ready from its packaging. Check before the initial
operation to make sure that the device has not been visibly damaged during
transport. If you detect any damage to the power cable or the casing, do not
operate the device. Contact your specialized dealer.
SAFETY INSTRUCTIONS
CAUTION!
Please exercise particular caution when handling AC 100 – 240 V, 50/60Hz power
voltage. This voltage rating may lead to a critical electrical shock! Any
damage caused by the non-observance of this operation manual excludes any
warranty claims. The manufacturer is not liable for any damage to property or
for personal injury caused by improper handling or non-observance of the
safety instructions.
WARNING!
To prevent fire or avoid an electric shock do not expose the device to water
or fluids! Never open the housing!
– This device left the factory in perfect condition. To maintain this
condition and to ensure a risk-free operation the user must observe the safety
instructions and warnings contained in this operation manual.
– For reasons of safety and certification (CE) the unauthorized conversion
and/or modification of the device is prohibited. Please note that in the event
of damage caused by the manual modification to this device any warranty claims
are excluded.
– The inside of the device does not contain any parts which require
maintenance, with the exception of wear parts that can be exchanged from the
outside. Qualified staff must carry out maintenance, otherwise, the warranty
does not apply!
– The fuse must exclusively be exchanged against fuses of the same class, with
the same trigger features and nominal current rating.
– Ensure that the power will only be supplied after the device has been fully
set up.
– Only use cables that comply with regulations. Observe that all jacks and
bushes are tightened and correctly hooked up. Refer to your dealer, if Do you
have any questions.
– Ensure that when setting up the product, the mains cable is not squashed or
damaged by sharp edges.
– Prevent the mains cable from coming into contact with other cables! Exercise
great care when handling mains cables and connections. Never touch these parts
with wet hands!
– Connect the power cable exclusively to appropriate shock-proof outlets. The
only supply point to be used is a supply outlet in accordance with the
specifications of the public supply network.
– Disconnect the device from the supply outlet when not in use and before
cleaning! Be sure to hold the mains plug by the body. Never pull the mains
cord!
– Position the device on a horizontal and stable low-flame base.
– Avoid any concussions or violent impact when installing or operating the
device.
– When selecting the location of installation, make sure that the device is
not exposed to excessive heat, humidity, and dust. Be sure that no cables lie
around openly. You will endanger your own safety and that of others!
– Do not rest any containers filled with liquid that could easily spill onto
the device or in its immediate vicinity. If, however, fluids should access the
inside of the device, immediately disconnect the mains plug. Has the device
been checked by a qualified service technician before re-use? Damage caused by
fluids inside the device is excluded from the warranty.
– Do not operate the device under extremely hot (in excess of 35° C) or
extremely cold (below 5° C) conditions. Keep the device away from direct
exposure to the sun and heat sources such as radiators, ovens, etc. (even
during transport in a closed vehicle). Always ensure sufficient ventilation.
– The device must not be operated after being taken from a cold environment
into a warm environment. The condensation caused hereby may destroy your
device. Do not switch on or operate the device until it has reached ambient
temperature!
– Controls and switches should never be treated with spray-on cleaning agents
and lubricants. This device should only be cleaned with a damp cloth. Never
use solvents or cleaning fluids with a petroleum base for cleaning.
– When relocating, the device should be transported in its original packaging.
– When starting operation, the crossfaders and volume controls of your
amplifier must be set to a minimum level. Bring the loudspeaker switches into
the “OFF” position. Wait between 8 to 10 seconds before increasing the volume
to avoid damage to loudspeakers.
– Devices supplied by voltage should not be left in the hands of children.
Please exercise particular care when in the presence of children.
– At commercial facilities the regulations for the prevention of accidents as
stipulated by the organization of professional associations must be observed.
– At schools, training facilities, hobbies, and self-help workshops the
operation of the device must be monitored with responsibility by trained
staff.
– Keep this operation manual in a safe place for later reference in the event
of questions or problems.
APPLICATION IN ACCORDANCE WITH REGULATIONS
– This device is a 2-channel DJ controller, which can regulate and mix audio
signals. The device needs to be connected to a tablet or computer and an audio
amplifier or active speakers.
– If the device is used for any other purposes than those described in the
operation manual, damage can be caused to the product, leading to the
exclusion of warranty rights. Moreover, any other application that does not
comply with the specified purpose harbors risks such as short circuit, fire,
electric shock, etc.
– The serial number determined by the manufacturer must never be removed to
uphold the warranty rights.
MAINTENANCE
– Check the technical safety of the device regularly for damage to the mains
line or the casing, as well as for wear of wear parts such as rotary and
sliding switches.
– If it is to be assumed that the safe operation is no longer feasible, then
the device must be disconnected and secured against accidental use.
Always disconnect the mains plug from the outlet!
– It must be assumed that a safe operation is no longer feasible, if the
device bears visible defects, if the device no longer functions, following
longer storage under unfavorable conditions, or after major transport stress.
CONTROLS
RIGHT PANEL
LEFT PANEL
DESIGNATIONS:
1. Gain
2. Equalizer (2-band)
3. Browse Encoder
4. Track Load Button
5. Filter
6. Headphones/Cue Buttons
7. SHIFT
8. Pitch Fader
9. Linefader
10. Crossfader
11. Jog Wheel
12. Performance Pads
13. Vinyl
14. Key Lock
15. Parameter Button
16. Loop Encoder| 17. FX ON Button
18. FX Control
19. MODE
20. SYNC
21. CUE
22. PLAY/PAUSE
23. Master Out (RCA)
24. Master Volume
25. Headphones/Cue Mix
26. Headphones/Cue Volume
27. Headphones Out (3,5mm Jack)
28. USB-A-iOS-Port
29. USB Source Switch
30. USB-B PC/Power Port
31. Kensington Lock
---|---
SCOPE OF DELIVERY:
– Reloop Ready
– RCA Cable
– USB Cable
– Instruction Manual
CONNECTING THE RELOOP READY:
MASTER OUT
Connect your main system (e.g. active speakers) to Master Out (RCA) -23-.
HEADPHONES/CUE OUT
Connect your headphones to Headphones Out -27-.
USB CONNECTION
If you want to use your Reloop Ready with a computer, connect it to the USB-B
PC/Power Port -30- and set the USB Source Switch -29- to PC.
NOTE!
If you want to use the day app with an iOS/iPadOS device, connect your Reloop
Ready to the USB-A iOS Port -28-, as well as a USB-power supply (5V, 2A) to
the USB-B Port -30- and select iOS via the USB Source Switch -29-.
SOFTWARE INSTALLATION & CONNECTION
SERATO DJ LITE INSTALLATION MAC OS X
– Go to www.serato.com click on products and select the download for “Serato
DJ Lite”.
– If you are not already logged in to www.serato.com, please create an
account.
– After you have logged in and clicked on Products ¬ Serato DJ Lite, you will
see the latest Serato DJ Lite version and a download banner on the right-hand
side.
– Click to download the installation file.
– Once the download is complete, you can start the installation.
– Read the terms and conditions and click „Agree“ when you are finished.
– Follow the different steps until the installation is complete.
– Afterwards, you will find your Serato DJ Lite software in the Applications
folder.
NOTE!
If you are running macOS High Sierra or higher, you may have to enable
Serato access in your security settings.
SERATO DJ LITE INSTALLATION WINDOWS
– Go to Serato.com click on products and select the download for “Serato DJ
Lite”.
– If you are not already logged in to Serato.com, please create an account.
– You will see the latest Serato DJ Lite version and a download banner on the
right-hand side.
– Click to download the installation file.
– The Serato DJ Lite Windows Installer appears as an ‚archived‘ zip file,
which can be opened with Windows Explorer. Alternatively, you can use your
favorite archive managers, such as Winzip or 7zip.
– Once the download is complete, you can start the installation.
– If you are using Windows Explorer, you can double-click on the downloaded
file and you will see the Serato DJ Lite executable.
– If you are using a third-party archive manager, such as Winzip or 7zip, you
can right-click on the context-sensitive menu and select „Extract Here“, which
will extract the Serato DJ Lite file and place it in the location you selected
to save the original file.
– Double-click the resulting Serato DJ Lite Exe file from the archive after
opening or extracting the archive to start the Serato DJ setup. You will now
see the license terms. Check the „I agree to the license terms and conditions“
box and then click „Install“.
NOTE!
When using Windows, it is necessary to install an ASIO driver!
Go to:
https://www.reloop.com/reloop-ready#headingproduct_view_panel_features to
download the ASIO driver, execute the downloaded driver file
and follow the installation steps.
DJAY IPAD/IPHONE INSTALLATION & CONNECTION:
You can download the day app from the App Store.
– Download the djay app from the App Store.
– Set the USB source switch -29- to “iOS”.
– Connect your existing Lightning or USB-C cable to the Reloop Ready‘s USB-A
“iOS” Port -28-, as well as to your “iOS” device.
– Open the previously downloaded day app.
Your Reloop Ready will be recognized automatically and can now be operated.
Attention!
Computer and “iOS” devices cannot be used simultaneously.
Always connect the supplied USB cable to the USB-B PC/Power Port -30- and connect it to a USB power supply. Please only use the original power cable of your tablet/smartphone or use an appropriate power supply unit (5V, 2A) to ensure a sufficient power supply. Alternatively, you can purchase the following USB power supply as a spare part: Item No.: 243382.
OPERATION SERATO DJ LITE:
-
GAIN
Use the Gain Control -1- to adjust the channel volume. -
EQUALIZER
With the 2-band Equalizer -2- you can adjust the treble and bass for channels 1 & 2. -
BROWSE ENCODER
Use the Browse Encoder -3- to navigate through your music libraries. Press the Browse Encoder -3- to confirm your selection.
SHIFT: To go back to one menu item, press SHIFT -7- + Browse Encoder -3-. -
TRACK LOAD
Press the Track Load button -4- to load a track to the desired deck. -
FILTER
Channel 1 & 2 have an individual Filter -5-. In the 12 o‘clock position the filter is switched off. Turning Filter -5- clockwise creates a high-pass effect,
turning it counter-clockwise creates a low-pass effect. -
HEADPHONES/CUE BUTTONS
With the Headphones/Cue Buttons -6- you can monitor the respective audio signal of channels 1 & 2. -
SHIFT
Pressing SHIFT -7- + a selected button activates the respective functions of the 2nd level, according to the labeling of the device.
NOTE!
Some functions of the 2nd level can only be executed with the
Serato DJ Pro version, these can be recognized by the additional PRO labeling. -
PITCH FADER
The Pitch Fader -8- determines the tempo of the track. -
LINEFADER
With the Linefader -9- you can adjust the output volume for channels 1 & 2. -
CROSSFADER
The Crossfader -10- switches between the left and right channels. -
JOG WHEEL
The Jog Wheel -11- is active by default in pitch bend mode. The surface is touch-sensitive and reacts to body tension. Turning the outer rim -11- can
be used to perform a pitch bend.
SHIFT: By pressing SHIFT -7- + turning the Jog Wheel -11- at the same time, you can perform the SKIP/quick search function (fast scroll through track). -
PERFORMANCE PADS
The Performance Pads -12- are color-coded drum pads that control the selected performance mode. The different performance modes can be
activated by holding the MODE Button -19- and pressing the subsequently selected Performance Pad mode -12-.
THE FOLLOWING PERFORMANCE MODES ARE AVAILABLE:
Hot Cue Mode = Triggers the 4 available cue points per deck and the pad colors light up in the corresponding colors.
– SHIFT: By pressing SHIFT -7- and the respective Cue Pad, the selected Cue Point will be deleted.
– PRO: In Serato DJ Pro you are able to set up 8 hot cues per deck.
Auto Loop Mode = Each of the 4 Performance Pads in the first row has a different loop length. Pressing it will activate it immediately according to the length, pressing it again will deactivate the Auto Loop. The 4 pre- assigned loop sizes on the Drum Pads can be changed via the Parameter Buttons -15-.
The Performance Pads in the second row (5-8) are assigned as follows:
– Pad 5: Move the selected loop backward in the track
– Pad 6: Adjust the reduction parameter to move the selected loop within the track
– Pad 7: Adjust the enlargement parameter to move the selected loop within the track
– Pad 8: Move the selected loop forward in the track
PRO: In Serato DJ Pro you can also half or double the selected loop by using the Parameter Buttons -15-.
Manual Loop Mode = The 4 Performance Pads in the first row are assigned to the following functions:
– Pad 1: Set Loop In
– Pad 2: Set Loop Out
– Pad 3: Loop On/Off
– Pad 4: Jump to activated Loop In, pressing Pad 4 again deactivates loop
PRO: In Serato DJ Pro the pads in the second row are assigned as follows:
– Pad 5: Upward Scrolling through loops
– Pad 6: Downwards Scrolling through loops
– Pad 6: Save activated loop to empty loop slot
– Pad 8: Not assigned
Sampler Mode = Triggers the respective sample in the sample bank using the 4 drum pads -12-.
SHIFT: Pressing SHIFT -7 + the active sample drum pad will stop playback of the sample.
PRO: In Serato DJ Pro you are able to load 8 samples to the Sample Bank.
NOTE!
In Serato DJ Lite, you only have access to the 4 Performance Modes listed above. With the exception of Auto Loop Mode, the Performance
Pads in the second row (5-8) are assigned with the same function in each DJ Lite Performance Mode, as follows:
– Pad 5: Reverse On/Off
– Pad 6: Hold to rewind the track
– Pad 7: Hold to forward the track
– Pad 8: Playback from temporarily set Cue point, if the Cue is not set, the start Cue is automatically set to the beginning of the track and will start playing immediately (CUP – Cue and Play)
If you are a Serato DJ Pro user, you will have access to 4 additional DJ Pro Performance Modes in the second row of the Performance Pad section -12-.
PRO P’n’T: Pitch Play Mode = In combination with the Pitch‘n’Time Expansion Pack you can play your cues in different keys via the Performance Pads -12-. There are 3 scales available. To switch between the scales, press the left or right Parameter Button -15- of the respective channel. The pad with the keynote is always lit white and the cue point is played in the regular pitch.
SHIFT: To select another hot cue point, hold down the SHIFT Button -7- and press the desired Performance Pad -12- (Hot Cue) at the same time.
PRO: Scratch Bank Mode = In Scratch Bank Mode you can assign 8 audio files from your Serato DJ Pro library to each of the 8 Performance Pads.
When a pad is pressed, the respective file is loaded onto the deck. The pads on the left will be loaded to deck 1 and the pads on the right will be loaded to deck 2. To set up your Scratch Bank files, click on the Scratch Bank icon in the top toolbar of Serato DJ Pro to display the Scratch Bank panel. In this panel, you can load or eject audio files to the respective scratch banks and select the desired settings. These settings include the starting point, repeat on/off and key lock on/off. By clicking on the button in the upper left corner of the Scratch Bank panel, you can switch between advanced and simple views.
SHIFT: Hold down SHIFT -7- and click on any Scratch Bank Pad to unload the currently loaded file and reload the title that was last loaded on this deck.
PRO: Loop Roll-Mode = Each Performance Pad in the first row (1-4) enables/disables a loop roll when the pad is held. Each Pad is assigned a specific
loop length of 1/8 – 1.
The Pads in the second row (5-8) control the Beat Jump function.
– Pad 5: Beat Jump backward
– Pad 6: Adjust the reduction parameter of the Beat Jump
– Pad 7: Adjust the enlargement parameter of the Beat Jump
– Pad 8: Beat Jump forward
PRO: Beat Grid Mode = In Beat Grid mode you can adjust the grid and track timing to the selected song. The pads in the first row (1-4) will adjust the grid of the track and the pads in the second row (5-8) will adjust the timing of the track. -
VINYL
Vinyl -13- switches from Pitch Bend Mode to Vinyl Mode, where you can use the Jog Wheels -11- to perform the scratch function.
PRO SHIFT: By pressing SHIFT -7- + Vinyl -13- you activate/deactivate Slip Mode. If slip mode is active, you can perform various actions (cue points or scratches) and the playing track will continue at exactly the position, where the track would be if, you had not performed any actions. -
KEYLOCK
Key Lock -14- activates/deactivates the Key Lock function.
PRO P’n’T SHIFT: In combination with the Pitch‘n’Time Expansion Pack, pressing SHIFT -7- + Key Lock activates/deactivates the Key Sync function.
This allows you to match the key of the current track to the key of the track on the other deck. -
PARAMETER BUTTONS (PRO PARAMETERS)
The Parameter Buttons -15- control the parameter functions for each deck, depending on the selected mode (e.g. FX parameter setting).
PRO SHIFT: By pressing SHIFT -7- + Parameter Buttons -15- you can control the parameter functions of the 2nd level, depending on the selected mode. -
LOOP ENCODER
By turning the Loop Encoder -16- you can select the loop length (1/32-32 bars). Pressing the Loop Encoder -16- activates the previously selected loop length, pressing it again deactivates the loop.
SHIFT: By holding down SHIFT -7- and rotating the respective Loop Encoder -16-, you can set the Beats Multiplier value for the software effects of the respective channel.
SHIFT: By holding down SHIFT -7- and pressing the loop encoder -16- to the beat, you can manually enter the timing of the software effects. -
FX ON BUTTONS
Use the FX ON Buttons -17- to activate/deactivate the 3 selected software effects in your effect bank.
SHIFT: Holding SHIFT -7- and pressing the FX ON Keys -17-, you can select the desired software effect for the respective effect bank. -
FX CONTROL
With FX Control -18- you can adjust the effect intensity (depth) of the effects activated in the effects bank. -
MODE
Holding the MODE button -19- + pressing a Pad Mode activates the selected Performance Mode (see: 12. Performance Pads).
PRO SHIFT: Holding down SHIFT -7- and pressing the MODE button -19- enters User Mode. Here you can assign the Performance Pads -12- according to your personal preferences. -
SYNC
SYNC -20- automatically synchronizes the BPM value of one track to the other deck.
SHIFT: Pressing SHIFT -7- + SYNC -20- will deactivate SYNC mode. -
CUE
Use the CUE Buttons -21- to create and trigger a temporary cue point. This is represented by a white cue marker. If the CUE Button -21- is pressed during playback, it automatically stops and jumps back to the set cue point (CUE play mode). If you pause playback and press the CUE Button -21-, a new cue point is created at the current track position (CUE pause mode). -
PLAY/PAUSE
PLAY/PAUSE -22- starts/pauses playback of the respective deck. -
MASTER OUT (CINCH)
Your main system (e.g. active speakers) is connected to the Master Out (RCA) -23- and controlled by the Master Volume control -24-. -
MASTER VOLUME
The Master Volume Control -24- is used to adjust the master volume output. -
HEADPHONES/CUE MIX
The Headphones/Cue Mix Control -25- mixes the volume balance between the channel and master signal in the headphones.
– LEFT = CUE
– CENTER = 50/50 Ratio
– RIGHT = Master -
HEADPHONES VOLUME
Use the Headphones/Cue Volume Control -26- to adjust the volume of your headphones signal. -
HEADPHONES/CUE OUT
The Headphones/Cue Output -27- is used to connect your headphones to your Reloop Ready. -
USB-A “OS PORT
The USB-A iOS Port -28- is used to connect an iOS device.
Please additionally connect a USB power supply to the USB-B PC/Power Port -30-.
NOTE!
If you want to use an iOS device, make sure that the USB Source Switch -29- is set to iOS. -
USB SOURCE SWITCH
Use the USB Source Switch -29- to switch between your desired USB mode (computer- or iOS-operation). -
USB-B PC/POWER PORT
Use the USB-B PC/Power Port -30- to connect a computer, as well as a USB power cable to charge your iOS device via the Reloop Ready.
NOTE!
If you want to use a computer, make sure that the USB Source Switch -29- is set to PC. -
KENSINGTON LOCK
The Kensington Lock -31- serves to secure your Reloop Ready from being stolen.
NOTE
PRO: Requires the Serato DJ Pro Version to unlock the Pro features & Performance Modes.
P’n’T: Requires the Serato Pitch’n’Time Expansion Pack.
MINIMUM SYSTEM REQUIREMENTS:
You can check the current Serato DJ Lite / Serato DJ Pro system requirements
for Mac or Windows at serato.com.
You can check the current day system requirements for „iOS“/“iPadOS“, Android,
Mac, or Windows at algoriddim.com.
TECHNICAL DATA:
Sound Card Resolution: ……………………………… 24bit / 48kHz
Frequency Response: ………………………………….20Hz-20kHz
Signal to Noise Ratio:………………………………….95DB (USB)
Total Harmonic Distortion: ………………………….<0.1%
Master Out: …………………………………………………RCA
Headphone Out: ………………………………………….3,5mm (1/8 Jack)
Power: …………………………………………………………DC-5V / 2A USB-B
Power Consumption iOS connection: ………….DC-5V / 2A USB-B
Power Consumption PC connection: …………..DC-5V / 500mA USB-B
Dimensions: …………………………………………………325mm x 48mm x 220mm
Weight: ……………………………………………………….. 1,143 kg
iPhone, iPad, iPod touch, iTunes, Mac, and Mac OS have registered trademarks
of Apple Inc. in the U.S. and other countries.
App Store is a service mark of Apple Inc.
iOS is a trademark containing Cisco trademark signs in the U.S. and other
countries.
Windows is a registered trademark of Microsoft Corporation in the United
States and other countries.
Serato DJ Lite, Serato DJ Intro, Serato DJ Pro, Serato DJ, and Scratch Live
have registered trademarks of Serato Limited.
Beatport is a trademark of Beatport, LLC.
Soundcloud is a trademark of SoundCloud Limited.
djay is a registered trademark of Algoriddim GmbH.
Tidal is a trademark of Aspiro AB.
The best source is a trademark of Beatsource, LLC.
Android, YouTube, Google Play, and the Google Play logo are registered
trademarks of Google Inc.
WARNING!
To prevent fire or avoid an electric shock do not expose the device to water
or fluids!
Never open the housing!
Keep information for further reference!
www.reloop.com
Reloop Trademark
Global Distribution GmbH & Co. KG
Schuckertstr. 28
48153 Muenster / Germany
© 2021
References
- DJ Software and DJ Apps | Algoriddim
- Serato | The world’s best DJ and music production software
- Reloop Welcome - Reloop
- Serato | The world’s best DJ and music production software
- Reloop Ready - Reloop
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>