reloop RMX44 BT DJ Mixer Instruction Manual

reloop RMX44 BT DJ Mixer

CAUTION!
For your own safety, please read this operation manual carefully before initial operation! All persons involved in the installation, set-ting-up, operation, maintenance and service of this device must be appropriately qualifi ed and observe this operation manual in de-tail. This product complies with the requirements of the applicable European and national regulations. Conformity has been proven. The respective statements and documents are deposited at the manufacturer.

WARNING!
To prevent fi re or avoid an electric shock do not expose the device to water or fl uids!
Never open the housing!

CAUTION! For your own safety, please read this operation manual carefully before initial operation! All persons involved in the installation, setting- up, operation, maintenance and service of this device must be appropriately qualified and observe this operation manual in detail. This product complies with the requirements of the applicable European and national regulations. Conformity has been proven. The respective statements and documents are deposited at the manufacturer.

Congratulations on purchasing your Reloop RMX-44 BT mixing console. Thank you for placing your trust in our disc jockey technology. Before operating this equipment, we ask you to carefully study and observe all instructions.
Please remove the Reloop RMX-44 BT from its packaging. Check before initial operation to make sure that the device has not been visibly damaged during transport. If you detect any damage to the power cable or the casing, do not operate the device. Contact your specialised dealer.

SAFETY INSTRUCTIONS

CAUTION! Please exercise particular caution when handling AC 100 – 240 V, 50/60Hz power voltage. This voltage rating may lead to a critical electrical shock! Any damage caused by the non-observance of this operation manual excludes any warranty claims. The manufacturer is not liable for any damage to property or for personal injury caused by improper handling or non-observance of the safety instructions.

• This device left the factory in perfect condition. To maintain this condition and to ensure a risk-free operation the user must observe the safety instructions and warnings contained in this operation manual.
•  For reasons of safety and certification (CE) the unauthorised conversion and/or modification of the device is prohibited. Please note that in the event of damage caused by the manual modification to this device any warranty claims are excluded.
•  The inside of the device does not contain any parts which require maintenance, with the exception of wear parts that can be exchanged from the outside. Qualified staff must carry out maintenance, otherwise the warranty does not apply!
•  The fuse must exclusively be exchanged against fuses of the same class, with the same trigger features and nominal current rating.
•  Ensure that the power will only be supplied after the device has been fully set up. Always plug in the mains plug last. Ensure that the mains switch is in the “OFF” position when connecting the device to power.
•  Only use cables that comply with regulations. Observe that all jacks and bushes are tightened and correctly hooked up. Refer to your dealer, if you have any questions.
•  Ensure that when setting up the product, the mains cable is not squashed or damaged by sharp edges.
•  Prevent the mains cable from coming into contact with other cables! Exercise great care when handling mains cables and connections. Never touch these parts with wet hands!
•  Connect the power cable exclusively to appropriate shock-proof outlets. The only supply point to be used is a supply outlet in accordance with specifications of the public supply network.
•  Disconnect the device from the supply outlet when not in use and before cleaning! Be sure to hold the mains plug by the body. Never pull the mains cord!
•  Position the device on a horizontal and stable low-flame base.
•  Avoid any concussions or violent impact when installing or operating the device.
•  When selecting the location of installation, make sure that the device is not exposed to excessive heat, humidity and dust. Be sure that no cables lie around openly. You will endanger your own safety and that of others!
•  Do not rest any containers filled with liquid that could easily spill onto the device or in its immediate vicinity. If, however, fluids should access the inside of the device, immediately disconnect the mains plug. Have the device checked by a qualified service technician before re-use. Damage caused by fluids inside the device is excluded from warranty.
•  Do not operate the device under extremely hot (in excess of 35° C) or extremely cold (below 5° C) conditions. Keep the device away from direct exposure to the sun and heat sources such as radiators, ovens, etc. (even during transport in a closed vehicle). Always ensure sufficient ventilation.
•  The device must not be operated after being taken from a cold environment into a warm environment. The condensation caused hereby may destroy your device. Do not switch on or operate the device until it has reached ambient temperature!
•  Controls and switches should never be treated with spray-on cleaning agents and lubricants. This device should only be cleaned with a damp cloth. Never use solvents or cleaning fluids with a petroleum base for cleaning.
•  When relocating, the device should be transported in its original packaging.
•  When starting operation, the crossfaders and volume controls of your amplifier must be set to minimum level. Bring the loudspeaker switches into the “OFF” position. Wait between 8 to 10 seconds before increasing the volume to avoid damage to loudspeakers and diplexer.
• Devices supplied by voltage should not be left in the hands of children. Please exercise particular care when in the presence of children.
•  At commercial facilities the regulations for the prevention of accidents as stipulated by the organization of professional associations must be observed.
• At schools, training facilities, hobby and self-help workshops the operation of the device must be monitored with responsibility by trained staff.
• Keep this operation manual in a safe place for later reference in the event of questions or problems.

APPLICATION IN ACCORDANCE WITH REGULATIONS

•  This device is a professional mixing console which can regulate and mix low level audio signals. The device is thereby connected between a signal source and an audio amplifier or active speakers, respectively.
• This product is authorised for connection to 100 – 240 V, 50/60 Hz AC via mains adapter (included) and is designed exclusively for indoor application.
• If the device is used for any other purposes than those described in the operation manual, damage can be caused to the product, leading to the exclusion of warranty rights. Moreover, any other application that does not comply with the specified purpose harbours risks such as short circuit, fire, electric shock, etc.
•  The serial number determined by the manufacturer must never be removed to uphold the warranty rights.

MAINTENANCE

• Check the technical safety of the device regularly for damage to the mains line or the casing, as well as for wear of wear parts such as rotary and sliding switches.
•  If it is to be assumed that the safe operation is no longer feasible, then the device must be disconnected and secured against accidental use. Always disconnect the mains plug from the outlet!
•  It must be assumed that a safe operation is no longer feasible, if the device bears visible defects, if the device no longer functions, following longer storage under unfavourable conditions or after major transport stress.

IMPORTANT NOTE : (For Mobile Device Configuration)

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IC IMPORTANT NOTE : (For Mobile Device Configuration)
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

OVERVIEW

GRAPHICS USER INTERFACE

BACKSIDE

DESIGNATIONS

SIGNAL INPUT CHANNELS

1. Signal Input Select Switch

2.  Gain Dial

3. 3-Band Equalizer

4. Master LEDs

5. Filter

6. Cue Button

7.  Linefader

8.  Crossfader Assign Switch

9. Crossfader

10.  Crossfader Curve Switch
    MIC CHANNEL

11. . Mic Level

12.  Level Control LED for Mic

13. . 2-Band Equalizer for Mic

14.  Mic Switch
    HEADPHONES SECTION

15. Mono/Stereo Split Select Switch

16. Cue Mix (Cue/Master Signal Ratio)

17.  Cue Volume (Volume Control Headphones Output)
    MASTER SECTION

18. Master Volume

19. LED for Master Signal

20. Balance Dial for Master Signal

21. Booth Volume
    CONNECTIONS

22. . MIC Input

23.  Headphone Out

24.  Power Connection

25.  Master Out RCA

26.  Master Out XLR (balanced)

27.  Booth Out

28. Record Out

29.  Channel Inputs

30.  GND

31. ON/OFF Switch

32.  Bluetooth Button

CONNECTING THE RMX-44 BT

LINE SIGNALS
Connect your line sources (CD player, tape deck, controller, etc.) to the corresponding line/CD Channel Inputs for channels 1 – 4 -29-.
PHONO SIGNALS
Connect your phono sources to the corresponding Phono Channel Inputs -2- and -3-29-.
Connect your turntables’ grounding cables to the GND grounding screw -30-.
MICROPHONE SIGNAL
Connect your microphone to the Mic Input -22-.
HEADPHONES
Connect your headphone to the Headphones Out -23-.
MASTER OUTPUT
Connect your sound system to the Master Out -25- (RCA) or Master Out Balanced XLR (balanced) -26-.
MONITOR OUTPUT
Connect your monitoring system to the Booth Out -27-.
REC OUTPUT
Connect a recording device of your choice to the Record Out -28-.
The Record Output provides a steady signal, independent from master signal.
POWER SUPPLY
Connect the power cable to the Power Connection -24-.
Connect the power cable to your power outlet.

OPERATION

POWER ON
After all connections have been carried out, you can turn on the device via the ON/OFF Switch -31-.

SIGNAL INPUT SELECT
Via the Signal Input Select Switch -1- you can select between line and CD sources for channel 1, CD and phono for channel 2 – 3 and CD, Bluetooth & line sources for channel 4. Please observe the captions of the single signal input switches.
GAIN
Via the Gain Dials -2- you can adjust the input volume for channels 1 – 4. Make sure that peak signals stay within the yellow range of the Master LED indicator -4-.
Use the Mic Level Dial -11- to adjust the microphone.
Make sure that the Mic LED -12- is only lit during signal peaks.
EQUALIZER
With the 3 Band Equalizers -3- you can adjust low, mid and high frequencies for channels 1 – 4.
Via the 2-Band Equalizer -13- you can adjust low and high frequencies for the MIC Channel.
FILTER
Channels 1 – 4 dispose of an individual, bipolar filter -5-.
In the 12 o‘clock position the filter is turned off.
When turning clockwise, a highpass effect will be generated; when turning counter-clockwise a lowpass effect will be generated.
LINEFADER
The Linefaders -7- are used to adjust the output volume for channels 1 – 4.
CROSSFADER
With the Crossfader -9- it is possible to switch between the left and right crossfader channel. The crossfader‘s curve can be adjusted via the Crossfader Curve Switch -10-. By switching the Crossfader Curve Switch to the left, it becomes “sharp”, namely good for scratching. By switching it to the right, the crossfader becomes “smooth”, namely good for long mixes.
You can use the Crossfader Assign Switch -8- to assign the crossfader sides A&B to channels 1 – 4.
NOTE! In THRU position no crossfader side is assigned to the respective channel.
MIC
By using the Mic Switch -14- you can activate the microphone and, as the case may be, the talkover effect. This means the suppression of the remaining channels via the microphone signal (Active Ducking Technology).
In the OFF position the channel is turned off. ON activates the microphone‘s signal, TLKOVR activates the talkover function (-18dB).
MONITORING
With the Cue Buttons -6- you can select the input channel(s) that you wish to monitor via your headphones.
With Cue Mix -16- you can fade between the channel(s) selected via the Cue Buttons and the master signal. In the CUE position you will only hear the monitoring channels selected via the Cue Buttons; in MASTER position you will only hear the master signal.
You can mix the signals seamlessly. This way you can simulate a mix via your headphone. With the Headphone Input Volume Dial -17- you can adjust your headphone volume level. Via the Mono/Stereo Switch -15- you can select the headphone channel‘s output mode.
MASTER SECTION
By using the Master Volume Dial -18- you can adjust the master output volume.
Make sure that the Master Signal‘s LED -19- is only visible in the yellow range.
Via the Master Balance Dial -20- it is possible to select the relation of the right and left output volume level. In the middle position the volume of the two channels is equal.
Adjust the booth output volume via the Booth Volume Dial -21-.
NOTE! The Rec Output -28- is not affected by the Volume Dials‘ -18-, -21- position.
BLUETOOTH CONNECTION
The transmission of the RMX-44 BT uses an audio receiving mode only.
(without transmission mode and BLE)

After powering on the RMX-44 BT, the Bluetooth connection will enter waiting mode (LED off). Activate Bluetooth on your external playback device and shortly press the Bluetooth Button -32- to connect your RMX-44 BT wirelessly via Bluetooth to your external device. Upon successful connection, the Bluetooth Button -32- will be permanently lit.

Please refer to to the PAIRING & CONNECTION MODES section for more information about the connection.
If the RMX-44 BT is not connected to a Bluetooth device, the Bluetooth Button LED -32- will not be lit.
Please also refer to your playback device‘s manual.
(Device name will be displayed as Reloop RMX-44 BT)
BUTTON DEFINITION:

• short press: t < 1 sec
•  long press (2 sec): 2 sec < t < 10 sec
•  long press (10 sec): t > 10 sec

BLUETOOTH MODES:

• waiting: LED off
• connecting: LED on/off 0,5 sec
• pairing: LED on/off 0,2 sec
• connected: LED on
• clearing: LED on/off 0,3 sec

PAIRING & CONNECTION MODES:
Waiting Mode:
short press
…….. => enter connecting mode (if pairing records available)
…….. => enter pairing mode (if no pairing records available)

long press (2 sec)
…….. => enter pairing mode to start pairing

Pairing Mode:
short press
…….. => cancel pairing and enter waiting mode
long press (2 sec)
…….. => no function

Connecting Mode:
short press
…….. => cancel connecting and enter waiting mode
long press (2 sec)
…….. => enter pairing mode

Connected Mode:
short press
…….. => cancel connection and enter waiting mode
long press (2 sec)
…….. => enter pairing mode

NOTE! Long press (10 sec) while in any mode, will clear up all the pairing records and enter to pairing mode!
If the RMX-44 BT is not connected to a Bluetooth device for more than 3 minutes, the Bluetooth connection will be turned off automatically. In this
case the Bluetooth Button -32- will not be lit. If you would like to reactivate the Bluetooth function, shortly press (2 sec) the Bluetooth Button -32-.

TECHNICAL SPECIFICATIONS

• Type: 4 Channel Bluetooth DJ Mixer

• Power Supply: AC 100 – 240V, 50/60Hz

• Consumption: 8.5W

• Dimensions: 320mm (W) X 379.4mm (D) X 106.4mm (H)

• Weight: 5.6kg

• Inputs:
  Line/CD: 10K OHM / 0 dBV (1V)

• Phono: 47K OHM / -36 dBV (15.85mV)

• Mic: 4.7K OHM / -40 dBV(10mV) (Unbalanced)

• Bluetooth: -15 dBFs (177mV)

• Outputs:
  Nominal Limited

• Master: 1K OHM / 1.9dBV (1.2V) +/- 1dB +/- 2dB

• Balanced: 600 OHM / 1.9dBV (1.2V) +/- 1dB +/- 2dB

• Booth: 1K OHM / 1.9dBV (1.2V) +/- 1dB +/- 2dB

• Rec: 1K OHM / -0.6dBV (933mV) +/- 1dB +/-2dB

• Phones: 33 OHM / -12.5dBV (236mV) +/- 1dB +/-2dB

• S/N Ratio: (1KHz Input, Gain & Master at 12 o’clock with A-w/20KHz LPF, input short when no signal)
  Nominal Limited

• Phono: 81,6dB 78,6dB Input at -36dBV

• Line/CD: 85,6dB 81dB Input at 0dBV

• Mic: 80,6dB 77,6dB Input at -40dBV

• Bluetooth: 80,6dB 77,6dB Input at -15dBFs

Reloop
a division of Global Distribution GmbH & Co. KG
Schuckertstraße 28
48153 Muenster / Germany
Fax +49.251.6099368
Subject to alterations.
Illustrations similar to original product.
Misprints excepted.

References

• Reloop Welcome - Reloop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>