reLOOP Flux 6X6 In-Out USB-C DVS Interface for Serato DJ Pro User Manual

Flux 6X6 In-Out USB-C DVS

Interface for Serrate DJ Pro
User Manual

Flux 6X6 In-Out USB-C DVS Interface for Serato DJ Pro

WARNING!
To prevent fire or avoid an electric shock do not expose the device to water or fluids!
Never open the housing!

ATTENTION! For your own safety, please read this operation manual carefully before the initial operation! All persons involved in the installation, setting-up, operation,  maintenance and service of this device must be appropriately qualified and observe this operation manual in detail. This product complies with the requirements of the  applicable European and national regulations. Conformity has been proven. The respective statements and documents are deposited at the manufacturer.
Before operating this equipment we ask you to carefully study and observe all instructions. Please remove the FLUX from its packaging. Check before an initial operation to  make sure that the device has not been visibly damaged during transport. If you detect any damage to the USB cable or the casing, do not operate the device. Contact your  specialized dealer.

SAFETY INSTRUCTIONS

CAUTION! Please exercise particular caution when handling power voltage. This voltage rating may lead to a critical electrical shock! Any damage caused by the non- observance of this operation manual excludes any warranty claims. The manufacturer is not liable for any damage to property or for personal injury caused by improper handling or non-observance of the safety instructions.

• This device left the factory in perfect condition. To maintain this condition and to ensure a risk-free operation the user must observe the safety instructions and warnings contained in this operation manual.

• For reasons of safety and certification (CE) the unauthorized conversion and/or modification of the device is prohibited.
  Please note that in the event of damage caused by the manual modification to this device, any warranty claims are excluded.

• The inside of the device does not contain any parts which require maintenance, with the exception of worn parts that can be exchanged from the outside. Qualified staff  must carry out maintenance, otherwise, the warranty does not apply!

• Ensure that the power will only be supplied after the device has been fully set up. Always plug in the USB plug last.

• Only use cables that comply with regulations. Observe that all jacks and bushes are tightened and correctly hooked up. Refer to your dealer if you have any questions.

• Ensure that when setting up the product the USB cable is not squashed or damaged by sharp edges.

• Exercise great care when handling USB cables and connections. Never touch these parts with wet hands!

• Disconnect the device when not in use and before cleaning! Be sure to hold the USB plug by the body. Never pull the USB cord!

• Position the device on a horizontal and stable base.

• Avoid any concussions or violent impact when installing or operating the device.

• When selecting the location of installation make sure that the device is not exposed to excessive heat, humidity, and dust. Be sure that no cables lie around openly. You will endanger your own safety and that of others!

• Do not rest any containers filled with liquid that could easily spill onto the device or its immediate vicinity. If, however, fluids should access the inside of the device,  immediately disconnect the USB plug. Have the device checked by a qualified service technician before reuse. Damage caused by fluids inside the device is excluded from the warranty.

• Do not operate the device under extremely hot (in excess of 35° C) or extremely cold (below 5° C) conditions. Keep the device away from direct exposure to the sun and heat sources such as radiators, ovens, etc. (even during transport in a closed vehicle). Never cover the cooling fan or vents. Always ensure sufficient ventilation.

• The device must not be operated after being taken from a cold environment into a warm environment. The condensation caused at this moment may destroy your  device. Do not switch on or operate the device until it has reached ambient temperature!

• Controls and switches should never be treated with spray-on cleaning agents and lubricants. This device should only be cleaned with a damp cloth. Never use solvents or  cleaning fluids with a petroleum base for cleaning.

• When relocating, the device should be transported in its original packaging.

• Devices supplied by voltage should not be left in the hands of children. Please exercise particular care when in the presence of children.

• At commercial facilities, the regulations for the prevention of accidents as stipulated by the organization of professional associations must be observed.

• At schools, training facilities, hobby and self-help workshops the operation of the device must be monitored with responsibility by trained staff.

• Keep this operation manual in a safe place for later reference in the event of questions or problems.

APPLICATION IN ACCORDANCE WITH REGULATIONS

• This device is a professional USB-C DVS interface. The FLUX interface converts the control signal coming from each deck into digital audio, to be sent via USB to the  Serato DJ software, which decodes that signal into a stream of information based on what the DJ is doing with the control disc. A virtual “deck” replicates the  movements of the control disc. Audio files loaded onto the virtual decks are then played back through the outputs of the hardware, with any manipulation of the control  disc reproduced on the audio, effectively emulating vinyl control of the files loaded into the software.
• If the device is used for other purposes than those described in the operation manual, damage can be caused to the product, leading to the exclusion of warranty rights.  Moreover, any other application that does not comply with the specified purpose harbors risks such as short circuits, fires, electrical shocks, etc.

MAINTENANCE

• Check the technical safety of the device regularly for damage to the USB cable or the casing, as well as for wear out of wear parts such as buttons and switches.
• If it is to be assumed that a safe operation is no longer feasible then the device must be disconnected and secured against accidental use. Always disconnect the USB  cable from the outlet!
• Disconnect the USB cable from your computer.
• It must be assumed that a safe operation is no longer feasible if the device bears visible defects, if the device no longer functions, following longer storage under unfavorable conditions or after major transport stress.

CONTROLS

FRONT

REAR

DESCRIPTION

1. Output Status LED (Deck 1 – Deck 3)
2. Input Status LED (Deck 1 – Deck 3)
3. Thru Button (Deck 1 / Deck 2)
4. Thru Button Status LED (Deck 1 / Deck 2)
5. USB-Hub Status LED
6. PD Status LED (Power Delivery)
7. USB/DC Status LED
8. Output RCA (Deck 1 – Deck 3/AUX)
9. Active USB Hub (x2)
10. USB-C PD (Power Delivery)
11. USB-C DC In
12. Input RCA (Deck 1 – Deck 3/AUX)
13. Earth Terminal
14. Phono/Line Source Switches

FUNCTIONS

1. The Output Status LED -1- and Input Status LED -2- will show the Output and Input signal levels:
   1.1 Output Signal
   – OFF: when less than -24 dBV (LINE).
   – FULLY LIT: when more than +2 dBV (LINE).
   – FLASHING: when more than +14 dBV (LINE) – indicating clipping.
   1.2 Input Signal
   – OFF: when less than -28 dBV (LINE) / -60 dBV (PHONO).
   – FULLY LIT: when more than -2 dBV (LINE) / -34 dBV (PHONO).
   – FLASHING: when more than +10 dBV (LINE) / -22 dBV (PHONO) – indicating clipping.

2. If the Thru Buttons -3- are enabled, the audio signal will be sent straight from the input to the output. This function is used in setups where no software is used (e.g.  vinyl) and the signal does not need to be sent to a computer. The Thru Button Status LED -4- will light up if Thru-mode is active.

3. USB Hub Status LED -5-:
   – OFF: when the FLUX is connected in the USB-C to PC port via USB-C to USB-A cable – USB Hub is in passive mode.
   – DIMMED: when a USB-A external power supply is connected to the USB-C DC IN port – USB Hub is in active mode (less than 0.8 A per port).
   – FULLY LIT: when a power source is supplied via either a USB-C computer or a USB-C external power supply (min 15 W) – USB Hub is in active mode (0.8 A per port).

4. The PD Status LED -6- lights up when a connected USB-C PD power supply is detected.

5. USB/DC Status LED -7-:
   – FLASHING BRIEFLY ON POWER-UP: warning. Power may be insufficient (below or equal to 500 mA) for high power consumption USB Hub connections.
   – DIMMED: FLUX is powered by a USB-A computer port or a USB-A external power supply (USB Hub may not be able to deliver full output power).
   – FULLY LIT: 15 W or more available either from a USB-C computer port or a USB-C power supply (USB Hub delivers maximum output power).

6. The Outputs -8- and Inputs -12- will be connected to your mixer and playback device (turntable/CD player).

7. Two active USB Hubs -9- for connecting accessories such as MIDI devices, etc.

8. The USB-C PD-Port -10- connects the FLUX to your computer.

9. The USB-C DC In -11- connects the FLUX to an external power supply.

10. Switch the source between Phono/Line signal with the Phono/Line Source Switches -14-.

CONNECTIONS

To integrate the FLUX into a typical DJ setup, connect it to your turntables (or CD players) and mixer as follows (¬ Page 7):

1. INPUTS
   Connect your turntables or CD players to the Deck Inputs -12- on the FLUX. If you are using turntables, connect their earth wires to the earth terminal -13- on either  the FLUX or your mixer.

2. INPUT LEVEL SELECTION
   Set each input to the correct input level using the Phono/Line switches -14-. Set the switches to UP for Phono (turntables) or DOWN for Line (CD players).

3. OUTPUTS
   Connect the Outputs -8- on the FLUX to the Line Inputs on your mixer.

4. CONNECT THE FLUX TO YOUR COMPUTER
   Using the provided USB cable, connect the USB-C PD port -10- on the FLUX to an available USB-C or USB-A port on your computer. Make sure you connect it directly to your computer, not through a hub or splitter.

POWER SUPPLY

If the FLUX is connected to external power via the USB-C DC IN -11-, it is self-powered and does not use power from the USB-C PD port. If no external power is supplied, the FLUX will draw power from the USB port on your computer. If your computer is powered via USB-C, you can power it with the FLUX by connecting the FLUX to external power via the USB-C DC IN -11-.

You must connect an external power supply to use the Thru Outputs without a computer. Thrus are turned on and off via the buttons on the interface.

If your computer is connected and you  activate the Thru Outputs, the signal will be sent straight from the Inputs to the Outputs, bypassing the signal flow to the computer.

SERATO DJ PRO & SERATO DVS

The FLUX includes a built-in Serato DJ Pro and Serato DVS license.
Download Serato DJ Pro from here: https://serato.com/dj/pro/downloads
Please see the recommended specifications on the download page.
After Serato DJ Pro has been installed on your computer, the software will activate itself when the FLUX is connected.
You can log in with an existing Serato account or create a new one. If you are using Windows, Serato DJ Pro will prompt you to install the required ASIO driver. Click  “Install” to proceed. If this does not work, you can also manually download and install the driver from here:
FLUX ASIO driver (Windows only): www.reloop.com/reloop- flux
If you have needle tracking issues, please see the following article on the Serato website: https://support.serato.com/hc/en-us/articles/202552220 -Diagnosing-the-Scope-Views

FIRMWARE UPDATE

!! Please check for any available firmware updates on www.reloop.com/reloop- flux !!
UPDATE INSTRUCTIONS FOR MACOS AND WINDOWS
Before proceeding, please make sure you have installed the latest Java Runtime Environment (JRE). You can download and install Java from the following link: https://www.java.com/en/download/
Note: If you are using Microsoft EDGE, you may be unable to download the Java (JRE) application. If so, please use a different browser for the download.

AFTER INSTALLING JAVA (JRE), PERFORM THE FOLLOWING STEPS:

1. Please make sure Serato DJ Pro or any other application is closed before performing the update.
2. Connect the FLUX to your computer via USB.
3. Launch the Relook Firmware Update App application*, click “Open” and select the “FLUX_V***.bin” firmware file from the download package. You will see the  currently installed firmware version and the new version displayed inside the updater.
4. Click “Start” and wait for the update (takes approximately 3~5 minutes).
5. Once finished, click “Close”.

The device‘s firmware has now been updated successfully and the FLUX is ready to use.
Note: In case of an issue or if the update takes longer than 20 minutes, disconnect the device and repeat the instructions above.

*: If you receive a warning message on macOS, proceed as follows:

1. Go into your system preferences by clicking on the Apple icon and select “System Preferences”.
2. Select “Security & Privacy” and make sure the “General” tab is selected.
3. Click “Allow”.

The updater application should now open. If not, double-click the Relook Firmware Update App application.

TECHNICAL SPECIFICATIONS

POWER:

• USB bus powered: Yes
• Recommended power: 2 A or higher
• Minimum power: 400 mA
• Maximum USB-PD throughput: 60 W
• Maximum USB Hub power output: 2 x 0.8 A = 8 W
• Supported external USB (type A or C) power supply: 5 V/1 A – 20 V/3 A
• Power supply priority: FLUX self-power -> USB Hub -> PD (to PC)

AUDIO:

• S/N Ratio (output reference level 1 kHz, +4 dB):
• Deck In (LINE signal input: 0 dBV): More than 83 dB
• Deck In (PHONO signal input: -32 dBV): More than 73 dB
• THD + N:
• LINE signal input: -4 dBV @1K / Less than 0.03% (1 kHz,+0 dB)
• PHONO signal input: -36 dBV @1K / Less than 0.05% (1 kHz,+0 dB,Inverse RIAA)
• Maximum Gain:
• Deck In (LINE): +4 dB ± 2 dB
• Deck In (PHONO): +36 dB ± 2 dB
• Maximum Input (1 kHz, THD=1%):
• Deck In (LINE): More than +7 dBV
• Deck In (PHONO): More than -25 dBV
• Maximum Output (1 kHz, THD=1%):
• Deck Output: More than +11 dBV

USB:

• USB audio interface with 24 bit/44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
• USB 2.0 high-speed (480 Mbit/s)
• Class-compliant
• USB Power Delivery Protocol 3.0

GENERAL:

• Dimensions (WxDxH): 160 x 120 x 34 mm
• Weight: 0.85 kg

ACCESSORIES:

• User Manual
• 1x USB type C/C cable
• 1x USB type C/A cable
• 2x RCA cables

SERVICE AND SUPPORT

For technical questions or issues, please check our FAQ or request a support ticket: https://www.reloop.com/faqs/

LEARN MORE ABOUT THE FULL

RELOOP PRODUCT RANGE

Relook Distribution
Global Distribution GmbH & Co. KG,
Schuckertstrasse 28, 48153 Muenster / Germany
Fax: +49.251.6099368
Subject to alterations.
Illustrations similar to original product.
Misprints excepted.

ASIO is a trademark of Steinberg Media Technologies GmbH.
Other trademarks and trade names are the property of their respective owners.
Other product, technology and company names, etc. mentioned herein are the trade names or registered trademarks of their respective owners.

References

• Reloop Welcome - Reloop
• Reloop Welcome - Reloop
• Download - Serato DJ - DJ Software
• java.com/de/download/
• Support - Reloop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>