reloop DSM3BT Smart Desktop Monitor System with Wireless Input Instruction Manual
- June 6, 2024
- reloop
Table of Contents
- SAFETY INSTRUCTIONS
- APPLICATION IN ACCORDANCE WITH REGULATIONS
- MAINTENANCE
- REAR SIDE
- LABELS
- FRONT SIDE
- LABELS
- ACCESSORIES
- INSTALLATION
- CLOSE-RANGE INSTALLATION
- MID-RANGE INSTALLATION
- CONNECTIONS
- OPERATION
- TONE CONTROL
- TECHNICAL DATA
- SUPPORT
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Smart Desktop Monitor System with Wireless Input
Instruction Manual
CAUTION!
For your own safety, please read this operation manual carefully before the
initial operation! All persons involved in the installation, setting-up,
operation, maintenance, and service of this device must be appropriately
qualified and observe this operation manual in detail. This product complies
with the requirements of the applicable European and national regulations.
Conformity has been proven. The respective statements and documents are
deposited at the manufacturer.
Please remove the Reloop DSM-3 BT from its packaging. Check before the initial
operation to make sure that the device has not been visibly damaged during
transport. If you detect any damage to the power cable or the casing, do not
operate the device. Contact your specialized dealer.
SAFETY INSTRUCTIONS
CAUTION!
Please exercise particular caution when handling AC 100 – 240 V, 50/60Hz power
voltage. This voltage rating may lead to a critical electrical shock! Any
damage caused by the non-observance of this operation manual excludes any
warranty claims. The manufacturer is not liable for any damage to property or
for personal injury caused by improper handling or non-observance of the
safety instructions.
WARNING!
To prevent fire or avoid an electric shock do not expose the device to water
or fluids! Never open the housing!
– This device left the factory in perfect condition. To maintain this
condition and to ensure a risk-free operation the user must observe the safety
instructions and warnings contained in this operation manual.
– For reasons of safety and certification (CE) the unauthorized conversion
and/or modification of the device is prohibited. Please note that in the event
of damage caused by the manual modification to this device any warranty claims
are excluded.
– The inside of the device does not contain any parts which require
maintenance, with the exception of wear parts that can be exchanged from the
outside. Qualified staff must carry out maintenance, otherwise, the warranty
does not apply!
– The fuse must exclusively be exchanged against fuses of the same class, with
the same trigger features and nominal current rating.
– Ensure that the power will only be supplied after the device has been fully
set up.
– Only use cables that comply with regulations. Observe that all jacks and
bushes are tightened and correctly hooked up. Refer to your dealer, if you
have any questions.
– Ensure that when setting up the product, the mains cable is not squashed or
damaged by sharp edges.
– Prevent the mains cable from coming into contact with other cables! Exercise
great care when handling main cables and connections. Never touch these parts
with wet hands!
– Connect the power cable exclusively to appropriate shock-proof outlets. The
only supply point to be used is a supply outlet in accordance with the
specifications of the public supply network.
– Disconnect the device from the supply outlet when not in use and before
cleaning! Be sure to hold the mains plug by the body. Never pull the main
cord!
– Position the device on a horizontal and stable low-flame base.
– Avoid any concussions or violent impact when installing or operating the
device.
– When selecting the location of installation, make sure that the device is
not exposed to excessive heat, humidity, and dust. Be sure that no cables lie
around openly. You will endanger your own safety and that of others!
– Do not rest any containers filled with liquid that could easily spill onto
the device or in its immediate vicinity. If, however, fluids should access the
inside of the device, immediately disconnect the mains plug. Has the device
been checked by a qualified service technician before re-use? Damage caused by
fluids inside the device is excluded from the warranty.
– Do not operate the device under extremely hot (in excess of 35° C) or
extremely cold (below 5° C) conditions.
Keep the device away from direct exposure to the sun and heat sources such as
radiators, ovens, etc. (even during transport in a closed vehicle). Always
ensure sufficient ventilation.
– The device must not be operated after being taken from a cold environment
into a warm environment. The condensation caused hereby may destroy your
device. Do not switch on or operate the device until it has reached ambient
temperature!
– Controls and switches should never be treated with spray-on cleaning agents
and lubricants. This device should only be cleaned with a damp cloth. Never
use solvents or cleaning fluids with a petroleum base for cleaning.
– When relocating, the device should be transported in its original packaging.
– To begin, the volume control on your Reloop DSM-3 BT monitors must be set to
„Minimum“ and the device must be switched off. Wait for 8 to 10 seconds before
increasing the volume to prevent damage to the speakers.
– Devices supplied by voltage should not be left in the hands of children.
Please exercise particular care when in the presence of children.
– At commercial facilities, the regulations for the prevention of accidents as
stipulated by the organization of professional associations must be observed.
– At schools, training facilities, hobbies, and self-help workshops the
operation of the device must be monitored with responsibility by trained
staff.
– Keep this operation manual in a safe place for later reference in the event
of questions or problems.
APPLICATION IN ACCORDANCE WITH REGULATIONS
– This device is a professional 2-channel active monitor system with Bluetooth
that you can use to listen to audio signals. To do so, the device can also be
connected to a computer, tablet, or smartphone via Bluetooth.
– If the device is used for any other purposes than those described in the
operation manual, damage can be caused to the product, leading to the
exclusion of warranty rights. Moreover, any other application that does not
comply with the specified purpose harbors risks such as short circuit, fire,
electric shock, etc.
– The serial number determined by the manufacturer must never be removed to
uphold the warranty rights.
MAINTENANCE
– Check the technical safety of the device regularly for damage to the mains
line or the casing, as well as for wear of wear parts such as rotary and
sliding switches.
– If it is to be assumed that the safe operation is no longer feasible, then
the device must be disconnected and secured against accidental use. Always
disconnect the mains plug from the outlet!
– It must be assumed that a safe operation is no longer feasible, if the
device bears visible defects, if the device no longer functions, following
longer storage under unfavorable conditions, or after major transport stress.
REAR SIDE
LABELS
MONITOR 1
-
Terminal connection for speaker 2
-
Signal input connector (cinch)
-
Subwoofer out (optional/3.5 mm jack)
-
Power cable connection
-
On/Off switch
MONITOR 2 -
Terminal connection for speaker 1
FRONT SIDE
LABELS
MONITOR 1
7. Bluetooth pairing button
8. Bluetooth pairing LED
9. Headphones output (3.5 mm jack)
10. Bass control dial
11. Treble control dial
12. Output volume control dial
ACCESSORIES
– Speaker cable (for left/right channel connection)
– Power cable
– Cinch to jack (3.5 mm) adapter cable
– Rubber pads
– Instruction Manual
INSTALLATION
- Please stick 4 of the rubber pads provided to the base of each of your DSM-3 BT monitors to protect them from vibrations and slipping.
- For optimum audibility of the high frequencies we recommend installing the tweeter of the studio monitors at face level; if necessary use an appropriate speaker stand. Be sure to use an even, stable underground; if necessary, use sound cushioning material.
- These speakers are near-field monitors which can be set up at a short distance to the listener.
- To avoid reflection from walls that are too close (e.g. room corners), turn the speakers slightly towards you. To optimize your ambiance acoustics, you may use sound-absorbing plates.
CLOSE-RANGE INSTALLATION
In studios, monitor speakers are usually positioned on the studio console (at head height). The monitors and the position of the listener should also form an isosceles triangle; in other words, place them at an angle of 60° to the listening position.
MID-RANGE INSTALLATION
The mid-range installation arrangement should be similar to the close-range installation setup. This variant is usually selected for larger monitors where they are too large or too heavy to be placed on the studio console. This set- up provides a larger „listening position“ and creates better acoustic conditions in the room. With mid-range installation, the bass for the monitors should be positioned above the studio console.
CONNECTIONS
- Connect both speakers using the speaker cable provided and the appropriate terminals (1)/(6). Insert the center wires into the sockets by pressing the terminal on the speaker jack.
- Now connect your signal source using the signal input connector (2) (cinch). You can connect an external subwoofer using the subwoofer out (3) if required.
- Connect the power cable supplied to the power cable connection (4) and plug it into your power socket.
OPERATION
-
ENSURE THE VOLUME CONTROL IS AT THE MINIMUM POSITION
Turn the volume control dial (12) to the Minimum position (turn controller left) before you switch the device on. -
TURN ON THE POWER
Once everything is connected, turn the device on using the On/Off switch (5). -
ADJUST THE VOLUME
Adjust the volume using the volume control dial (12). -
SELECT SIGNAL INPUT
You have the choice of 2 possible signal input sources:
Cinch (2)
Bluetooth (7)
To connect a playback device via cinch, connect the cinch cable of your
playback unit using the cinch socket (2) on the DSM-3 BT monitor 1.
NOTE
Please ensure that the signal strength of your chosen playback device is
sufficient. Many playback devices, for example, various record players may
require an additional preamplifier for direct connection to achieve sufficient
signal strength.
When the DSM-3 BT is turned on, the Bluetooth pairing LED (8) glows white. To
use a Bluetooth playback device, first, enable Bluetooth on the chosen
playback device and then press the Bluetooth pairing button (7) on your DSM3
BT monitor1.
When the DSM-3 BT appears on your Bluetooth device, press „Connect“. While in
pairing mode, the Bluetooth pairing LED (8) will flash blue and white
alternately. Once the connection is established, the Bluetooth pairing LED (8)
will glow blue. To connect to a different Bluetooth device, press the
Bluetooth pairing button (7) again to cancel the active Bluetooth connection
and return to pairing mode. Repeat the process described above.
TONE CONTROL
You can raise or lower the bass and treble using the bass controller (10) and treble controller (11). The ideal setting will depend on the particular features of the room. A room with excellent sound insulation will need the higher frequencies increasing. Conversely, higher frequencies need lowering in rooms with reverberation.
TECHNICAL DATA
– Type: 2-channel bass reflex, active monitor speaker system
– Tweeter: 0.5“ tweeter (1.30 cm)
– Woofer: 3.5“ bass (8.89 cm)
– Housing dimensions: 140 x 222 x 152.5 mm
– Weight: 2.8kg (pair)
– Frequency range: 80-20,000 Hz
– Amplifier power: class A/B amplifier: 2 x 20 W RMS
– Magnetic shielding
– Inputs: 1 x line (RCA), 1 x wireless Bluetooth ®
– Outputs: 1 x headphone monitor (3.5 mm jack), 1 x subwoofer (3.5 mm jack)
SUPPORT
If you require further help or have technical questions, please see our Reloop
FAQs or contact our support team: https://www.reloop.com/faqs.html
https://www.reloop.com/support-ticket-request
In compliance with international safety certification requirements (e.g. CE,
UKCA, FCC), all necessary documents are held by our official Importer. You can
find our current importer for your territory listed as Distributor in the
‘Where To Buy section’ of our website: https://www.reloop.com/dealer-area
WARNING!
To prevent fire or avoid an electric shock do not expose the device to water
or fluids! Never open the housing!
Keep information for further reference!
www.reloop.com
Reloop Trademark
Global Distribution GmbH & Co. KG
Schuckertstr. 28
48153 Muenster / Germany
© 2021
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>